Log in to the menu of the Xiaomi router via your computer: full instructions with error solutions

Introduction: why you need access to a router through a PC

Xiaomi routers are among the most popular devices for home networking due to the combination of affordable prices, stable operation and extensive customization. However, many users face difficulties when first logging into a web management interface via a computer. Unlike the Mi Wi-Fi mobile application, the web panel allows you to fine-tune network settings, monitor connected devices and update firmware without a smartphone.

In this article, you will find step-by-step instructions for logging into the menu of the Xiaomi router from a Windows, macOS or Linux PC, learn the standard data for authorization, and learn how to solve typical problems - from the "Page is not available" error to the forgotten password. 4A/4C/4Q, AX3600 and AX6000, The instructions are also valid for other versions.

Before you start, make sure your computer is connected to the router via Ethernet cable (recommended) or Wi-Fi, which will eliminate connection problems during the login phase.

Preparation for the entrance: what will be needed

To successfully go to the settings of the Xiaomi router, prepare:

• 🖥️ Computer or laptop with any browser (Chrome, Firefox, Edge) Do not use mobile browsers - some panel features may not display correctly.
• 🔌 Ethernet cable (optional but recommended for stability) If you connect over Wi-Fi, make sure the signal is stable.
• 📝 Authorization data: standard login/password or personal if you have changed them. Most Xiaomi models use a combination of the same. admin/admin.
• 🔄 IP-router address: usually 192.168.31.1 or 192.168.0.1, but may vary depending on the firmware.

If you have previously changed the network settings of the router (for example, disabled) DHCP), IP-The address may have changed. In this case, check it through the command line:

ipconfig (for Windows)


ifconfig (for macOS/Linux)

Look for the Default Gateway line – this is the current IP of your router.

Standard login data: login and password

The manufacturer sets universal credentials for all Xiaomi router models, unless the user has manually modified them.

On AX series routers (such as the AX3600), the default password is on the sticker underneath the device. If the sticker is erased, try the admin/admin combination or reset.

If you forget your personal password, you can only reset it through a hardware reset (Reset button on the case), and more on this in the problem solving section.

💡

Take a picture of the sticker with the router data (usually on the bottom panel) before you first log in, which will help avoid login problems in the future.

Step-by-step instructions: how to go to the settings of the router

Follow this algorithm to open the web management interface:

1. Connect your computer to the router with an Ethernet cable (LAN port) or Wi-Fi. For stability, it is better to use a wired connection.
2. Open the browser and enter in the address bar IP-router address (such as 192.168.31.1) or miwifi.com domain.
3. Wait for the login page to load. If the site doesn't open, check the connection or try another browser.
4. Enter your login and password (standard or personal).
5. Check out the main panel. This shows the basic network settings: connected devices, Internet speed, firmware version.

If you see an error instead of a control panel ERR_CONNECTION_REFUSED or the Site is not available, go to the Troubleshooting section.

Is an Ethernet cable connected to a LAN (not a WAN) port?

Is VPN/proxy disabled in the browser?

Is it properly administered? IP-address http://)?

Have you tried a different browser (e.g. Chrome)?-->

Problem Solving: What to do if you can’t get in

Let’s look at common mistakes and ways to eliminate them:

1. Page does not open (connection error)

• 🔌 Check the physical connection of the cable. Try another port. LAN router.
• 🌐 Make sure you enter the correct one. IP. For Xiaomi, it’s almost always 192.168.31.1, but if you changed your network settings, the address might have changed.
• 🔄 Restart the router (power button or remove the plug from the socket for 30 seconds).
• 🛡️ Disable Windows Firewall or Antivirus – They Can Block Access.

Incorrect login/password

• 🔑 Try the standard combinations: admin/admin or admin/12345678.
• 📝 Check the sticker on the router – sometimes the password is listed there.
• 🔄 If you forget your password, reset your settings (see below).

3.The router does not respond after changing settings

If you've changed before IP-router address or shut down DHCP, Access can be returned through:

• 🔧 Reset to factory settings (reset button for 10 seconds).
• 🔍 Finding a new IP via the command line (arp command) -a).

⚠️ Warning: Resetting will remove all of your personal settings, including your Wi-Fi name, network password, and firewall rules.

Navigation on the web interface: the main sections

After a successful login, you will see the main control panel, and consider the key sections (the name may vary slightly depending on the model and firmware):

• 📊 Status – information about current Internet connection, IP-addresses, working hours.
• 📶 Wi-Fi – setting up the network name (SSID), password, channel, mode of operation (2.4/5 GHz).
• 🔒 Safety – firewall control, filtration MAC-addresses, parental control.
• 🔄 System - firmware update, backup / restore settings, change of admin password.
• 📡 In addition, setting up DMZ, Port forwarding (port forwarding), VPN.

For beginners, it’s helpful to start with the Wi-Fi section, where you can change your network name and password, and enable guest access. Power users often use Port Redirects to set up remote access to cameras or servers.

💡

Always update your router firmware in System → Update, which fixes security vulnerabilities and improves stability.

Additional ways to manage the Xiaomi router

In addition to the web interface, you can manage the router through:

• 📱 Mobile application Mi Wi-Fi – convenient for quick actions (reboot, lock devices), but the functionality is limited compared to the PC version.
• 🖥️ Telnet/SSH — for power users. Requires access enabled in router settings (System) → Remote control).

If you prefer a mobile app, keep in mind that the initial setup will still require a computer login — for example, to enable remote access.

⚠️ Attention: Enable access to Telnet/SSH This method only works when necessary and disables access after completion of work.

FAQ: Answers to Frequent Questions