How to carefully remove the back cover Xiaomi Redmi 7A: tools, risks and step-by-step analysis

Removing the back cover of the Xiaomi Redmi 7A smartphone is a challenge that owners face when replacing the battery, repairing the speaker or cleaning from dust. Despite its apparent simplicity, the procedure requires caution: plastic latches are fragile, and improper exposure can lead to cracks in the case or damage to the plumes. This instruction will help disassemble the device without consequences, even if you have no experience in repairing equipment.

The Redmi 7A, codenamed pine, was released in 2019 and is a low-end model, so it doesn't have easy access to its insides. Unlike the magnetically attached flagships, it's only a plastic latch that loses its elasticity over time. If you've never taken your smartphone apart, start with preparation, and it saves you time and nerves.

In this article, you'll find not only a step-by-step algorithm, but also a list of tools you need, common errors, and tips for handling adhesives (if any), and a separate look at what to do if the lid fails or the latches break, and for clarity, a comparative table of alternative methods and risks for each of them.

Preparing for the removal of the lid: tools and safety

Before you start disassembling, make sure you have everything you need. Lack of the right tools is the main cause of damage to the hull. Redmi 7A will require:

• 🔧 Plastic blade (or mediator) - to disconnect latches without scratches.
• 🔥 Dryer or thermo-air station - if the lid is glued (occurring in some batches).
• 🧲 Suction (optional) - helps to separate the lid from the body with a strong fit.
• 🔍 Loop or magnifying glass to see small latches.
• 📦 Container for screws - if you plan to withdraw the fee (in Redmi) 7A Small screws, easily lost).

Important: Don't use metal screwdrivers or knives, they leave traces and can break latches, and if you don't have a plastic blade, you can replace it with a credit card (preferably expired), but you need to be very careful.

⚠️ Warning: Before disassembling, turn off your smartphone and remove it SIM-A memory card, and heating the body with a hairdryer when the device is on, can cause battery damage or even fire.

If you remove the battery cover, pre-order the original 4,000 mAh battery (MB-J10B) and fakes are often smaller and can swell in a few months.

Step-by-step: how to remove the cover without damage

The Redmi 7A’s lid removal algorithm differs from other Xiaomi models due to the design features.

1. Heat the case (if the lid is glued). Turn the dryer on to minimum power and warm up the edges of the smartphone for 1-2 minutes. Keep the hair dryer at a distance of 10-15 cm to avoid melting the plastic. Temperatures above 60 °C can damage the display and battery.
2. Separate the lid. Put the plastic blade in the gap between the lid and the body at the charging connector (the weakest point). Carefully drive the blade along the edge, alternately snapping the mounts. Don't try to separate the lid immediately, this will cause the latch to break.
3. Trail check. Once you remove the lid, you'll see a flexible fingerprint scanner plume (if you have one in your version). Don't pull it, first disconnect the connector on the motherboard.

If the lid doesn't lend itself, don't put too much effort into it. You may have missed one of the latches. Check the case for hidden mounts -- in Redmi 7A, they're next to the volume buttons and the camera.

Check availability of all tools |

Turn off the smartphone and remove SIM-map|

Warm up the edges of the body with a hairdryer (if necessary)|

Start the separation of the cover from the charging connector |

Disconnect the plumes before complete removal-->

What to do if the latches break: repairs and alternatives

Broken latches are a common problem when disassembling the Redmi 7A. If you hear a characteristic crack, don't panic: the lid can be locked in alternative ways. Here are the possible solutions:

• 🔧 Clay. B-7000 — It's transparent, it's elastic, it doesn't damage the plastic, it's applied point-by-point to the mounting.
• 🧲 Double-sided Scotch – suitable for temporary fixation, but can leave traces.
• 🔨 3D-Print new latches – if you have access to 3D-printer, you can restore the mounts on the template.

If the latches broke the first time you removed the lid, you probably used the wrong tools or made an effort in the wrong place. Service centers charge 500 to 1,500 rubles to replace the latches, but with a neat adhesive repair, you can do without it.

⚠️ Warning: If you find the battery swelling after removing the lid, stop working immediately! The bloated battery may ignite if punctured or deformed.

💡

If you often disassemble a smartphone, buy a set of plastic blades with different thicknesses. For the Redmi 7A, a 0.5 mm blade is optimal - it penetrates into the gap without damaging the body.

Disassembly of further components: what can be done after removing the lid

After successfully removing the lid, you get access to the main components of the Redmi 7A. Here’s what you can do next:

• 🔋 Battery replacement is the most common cause of disassembly, and the new battery will bring autonomy back to level. 1.5-2 daytime with moderate use.
• 📞 Clean speaker and microphone - dust and dirt reduce sound quality. Use a soft brush or compressed air.
• 📶 Replacement of antenna module – if the network signal deteriorates, the problem may be oxidized contacts.
• 🔧 Trail check – rubbed or torn plumes cause problems with the display or buttons.

If you are planning to replace the display module, note that in the Redmi 7A it is glued to the frame. The separation will require a special additive tool and heating to 80-90 ° C. Without experience, it is better to entrust this to professionals - an error will lead to a broken touchscreen.

When working with internal components, watch for antistatic discharge. Touching the motherboard with your bare hands can damage the chips. Use an antistatic bracelet or periodically touch a grounded metal object.

Frequent Mistakes and How to Avoid Them

Even experienced users make mistakes when disassembling the Redmi 7A. Here are the most common of them and ways to prevent:

• 🔥 Overheating of the case — if you heat it with a hair dryer for too long, the plastic will deform. Use a thermometer to control the temperature.
• 🔧 Too deep penetration of the shoulder blade, you can damage the flexible plumes. 15-20°.
• 📱 Sloppy handling of the battery - don't bend it or put it on metal surfaces.
• 🔩 Loss of screws at Redmi 7A They use screws of different lengths. Take a picture of their location before extraction.

Another common problem is damage to the sealing gum (if any). Redmi 7A does not have official water protection, but some modifications have a sealing gasket. If it breaks, the smartphone will become more vulnerable to moisture, in which case, after assembly, it is recommended to apply a hydrophobic coating (for example, Nano-Coating) on the board.

💡

If you are not sure of your abilities, it is better to contact the service. The cost of dismantling the Redmi 7A in the workshops starts from 300 rubles, which is cheaper than repairing damaged components.

Smartphone Assembly: How to Close the Cover

Building a Redmi 7A after disassembly is as important as disassembling it. Incorrect assembly can lead to a poor fit of the lid, creaking or even damage to the internal components.

1. Check all the plumes. Make sure the fingerprint connectors, speaker and cameras are tightly connected, without any distortion.
2. Line the lid. Start at the top (where the camera is) and press it gently against the body as you move down. The latches should be in place with a slight click.
3. Check the buttons. After assembly, press the volume and power buttons -- they should run smoothly, without jamming.

If the lid doesn't sit tight, don't force it. One of the latches probably didn't fit. Take the lid off carefully and repeat the process. In some cases, a slight tapping of the edges with your palm helps, which helps to help the latches get into the grooves.

After assembly, turn on the smartphone and check:

• Touch screen operation.
• Charging (connect the cable).
• Sound quality in the speaker and microphone.
• Network signal and Wi-Fi.

⚠️ Warning: If the smartphone doesn't turn on after assembly, check the battery connection. Often the reason is a departed power connector on the motherboard.

Alternative methods of removing the lid: pros and cons

In addition to the standard method with a shoulder blade, there are alternative ways to remove the cover of the Redmi 7A. They are suitable for different situations, but have their own risks.

The fishing line is particularly popular among craftsmen, as it allows you to carefully separate the lid without the risk of breaking the latches. This requires a line with a thickness of 0.3-0.5 mm and patience: the process can take up to 20-30 minutes.

If you decide to use an oven, watch the temperature! Exceeding 70°C can melt plastic elements or damage the display. This method is only suitable for advanced users.

FAQ: Answers to Frequent Questions