Xiaomi RedmiBook Pro 8 laptops have gained popularity due to their balanced performance, stylish design and affordable price. However, even such reliable devices can experience problems over time, from replacing the thermal paste to upgrading RAM or SSD. The first step in any repair is to remove the back cover - an operation that requires accuracy and knowledge of the design features of the model.
Unlike many budget laptops, the RedmiBook Pro 8 has a non-shatterable body with hidden latches and screws under rubber legs. Mistakes in dismantling the lid can lead to cracks in plastic, damage to plumes or even failure of the motherboard.
Preparation for disassembly: tools and precautions
Before you start removing the lid, make sure you have everything you need, and using the wrong tools is one of the main causes of damage to the hull.
- ✅ Plastic mediators (2-3 (a) for the purpose of gently removing the
- ✅ Cross screwdriver PH00 — for screw cover (normal) PH0 may break the slime!)
- ✅ Suction (optional) - helps to lift the cover after loosening the latches
- ✅ Antistatic bracelet – protection against static electricity
- ✅ A thin flat screwdriver - for smacking rubber legs
- ✅ Container for screws - so as not to lose small details
Pay special attention to the screws under the rubber legs — they are often forgotten to unscrew, which leads to cracks in the case when you try to remove the lid. Also recommend working on a clean, flat surface with good lighting. If you are disassembling a laptop for the first time, take a picture of each step — this will help with the reverse assembly.
⚠️ Warning: Do not use metal tools to crack the clamps! Plastic mediators minimize the risk of damage to the body. Even a small scratch on an aluminum surface can become a hotbed of corrosion.
Step-by-step: remove the back cover of RedmiBook Pro 8
The disassembly process consists of several key steps, and follow the instructions strictly in order to avoid errors:
- Turn off the power. Turn off the laptop, disconnect the charger, and remove the battery (if possible without removing the lid). In the RedmiBook Pro 8, the battery is built-in, so this step is skipped.
- Remove the rubber legs. Carefully tuck them in with a thin screwdriver, there are screws underneath. This model usually has 4 legs (2 large and 2 small).
- Spinning. There are 10 screws on the lid: 8 perimeter short and 2 long around the hinges. Use the PH00 screwdriver and don't put too much effort into it.
- Click clips. Starting at the corner near the touchpad, gently insert a plastic mediator into the gap between the lid and the body. Move around the perimeter, alternately loosening the latches.
The hardest part is the loop area, where the latches are tighter, and they're easy to break. If the lid doesn't lend itself, check again if all the screws are twisted. If you approach them correctly, you'll hear the characteristic clicks of the loosened clamps.
☑️ Check before removing the lid
⚠️ Attention: If you feel strong resistance when you crack the lid, don't use force! You probably missed the screw or the latch. In the RedmiBook Pro 8, the clamps near the vents are the most vulnerable - they are easy to break if you disassemble them sloppyly.
Common Mistakes and How to Avoid Them
Even experienced users sometimes make mistakes when disassembling the Xiaomi RedmiBook Pro 8. Here are the most common problems and ways to prevent them:
| Mistake. | Effects of consequences | How to avoid |
|---|---|---|
| Use of a metal latch screwdriver | Scratches, chips, damage to antenna cables | Use only plastic mediators |
| Missed screws under the legs | Cracks of the body when trying to remove the cover | Check all 4 legs carefully |
| Excessive force in the case of deflection | Broken clamps, deformation of the body | Move gradually, listening to clicks |
| Incorrect withdrawal sequence | Touchpad plume damage | Start at the corner near the touchpad |
The special attention is given to the track of the touchpad that runs under the lid near the left hand, which is easily damaged when removed carelessly, and if the touchpad stops working after disassembly, check the integrity of the track and the density of its connection to the motherboard.
💡
Before disassembling, try removing the lid from only one side (such as near the touchpad) and make sure all latches are loosened, which will help avoid unpleasant surprises in the form of untwisted screws.
What to do after removing the cover: further actions
When the lid is successfully removed, you will have access to the main components of the laptop. In the RedmiBook Pro 8, you will see:
- 🖥️ Motherboard with processor and chipset
- 💾 M.2 SSD (metal-coated)
- 🧊 Cooling system with heat pipes
- 🔋 Battery (built-in, 56 Wh)
- 📡 Wi-Fi module (Intel or Qualcomm)
If your goal is to replace the thermopaste, be prepared for the fact that in this model the radiator is attached to the processor through 4 screws with springs. When you reverse assemble them, it is important to twist them cross-cross to ensure uniform pressure. RAM You will need a complete dismantling - memory soldered to the motherboard.
How to check the condition of the thermal paste without disassembly
Reverse Assembly: nuances and performance check
Getting your laptop back together is often harder than disassembling it, and here are some key points to consider:
- Check the density of all the plumes (especially the touchpad and keyboard).
- Make sure that Wi-Fi antenna cables are not clamped and properly stacked.
- Write the screws in reverse sequence - first long at the loops, then short around the perimeter.
- Before final assembly, turn on the laptop with the connected power (without the cover) and check the operability of all components.
After assembly, be sure to test: Keyboard (all keys), Touchpad (gestures and clicks), Wi-Fi/Bluetooth (network connection), Sound (speakers and microphone), Ports (USB, HDMI, Type-C). If something doesn't work, disassemble the laptop again and check for the connection of the corresponding plumes.
⚠️ Attention: If the laptop doesn't turn on after assembly, check the battery connection and motherboard power.RedmiBook Pro 8 often has a problem with the battery's retractable connector - it needs to be tightly inserted before clicking.
💡
The most common reverse assembly error is compressed cables, which can cause plumes to break or short circuit, and always stack the wires as they were originally laid.
When to contact the service center
Although the dismantling of Xiaomi RedmiBook Pro 8 is quite capable of an experienced user, there are situations when it is better to trust the professionals:
- 🔧 If you have never taken a laptop before
- 💻 If you need to replace the motherboard or chip BIOS
- 🔥 If the laptop was exposed to liquid or overheating
- 🛠️ If after self-disassembly there were artifacts on the screen or problems with power
The cost of dismantling in the service center usually does not exceed 1000-1500 rubles, but you get a guarantee for the work done. If you decide to act on your own, but something went wrong, do not try to "fix" the consequences - this can aggravate the problem. For example, a damaged screen plume is often soldered at home, which in 90% of cases leads to complete inoperability of the display.