How to remove film from the TV Xiaomi: 3 proven ways without divorce

The factory protective film on Xiaomi Mi TV, Redmi Smart TV or Xiaomi TV A Pro is a temporary coating that the manufacturer applies to protect the matrix from scratches during transportation and first unpacking. However, many users face problems when removing it: sticky traces remain, divorces appear, and sometimes the film breaks off in pieces, leaving hard-to-removal glue on the screen. In this article, we will discuss three safe methods of film removal, explain what errors lead to damage to the screen, and give recommendations for further care of the TV.

The feature of the films on Xiaomi is their two-layer structure: the top layer (smooth) is easily separated, and the bottom (glue) often remains on the matrix. If you do not act correctly, you can damage the anti-reflective coating or leave micro scratches. We tested all methods on the models of Mi TV 4S 55, Redmi Smart TV X50 and Xiaomi TV Q2 65" - the results are summarized in the comparison table below.

Before you start, check that your film is exactly factory-made, not decorative (like on a TV frame). Decorative stickers don't have to be removed - they're part of the design. How do you tell the difference? Factory film always covers the entire screen, including the perimeter frame, and has microscopic air bubbles under the surface.

1.Preparation: What will be required to safely remove the film

Don't try to take the film dry, which is the most common mistake that causes tears and sticky marks.

• 🧴 Screen cleaning tool (no alcohol!): Xiaomi Screen Cleaner or any water-based spray for monitors is fine. Alcohol solutions destroy the anti-reflective coating.
• 🧻 Microfiber wipe (2-3 pieces): one for wetting, one for dry polishing. Do not use paper towels or conventional rags!
• 📏 Plastic scraper or bank card: for tweaking the edge of the film. Metal objects (knives, blades) are strictly prohibited.
• 💧 Distilled water (optional): if there is no special spray, you can dilute 1 drop of dishwashing products in 100 ml of water.

The room temperature should be 18-25°C. At lower temperatures, the adhesive layer becomes brittle and breaks off in pieces. If the TV has just been brought in from the cold, let it warm up for 1-2 hours.

⚠️ Attention: Never take the film off the TV on! The matrix heats up and the glue becomes stickier. All manipulations are done when the power is off, disconnecting the cord from the socket.

If the film has already partially moved around the edges, do not pull it, so you will tear the main layer. Better gently tuck the edge with a plastic scraper and moisten it with a cleaner, as described in the next section.

Method 1: Film removal with a wet wipe (for new TV sets)

This method is suitable if the film has not yet "stick" to the screen (usually in the first 1-2 weeks after purchase).

1. Apply the screen cleaner to a microfiber wipe (not the TV itself!).
2. Gently wipe the edge of the film around the perimeter of the screen, paying attention to the corners - there the glue is held stronger.
3. Wait 30 to 60 seconds until the liquid softens the adhesive layer.
4. Tap the edge of the film with a plastic scraper and slowly pull parallel to the screen (not up!).
5. If the film breaks, stop and repeat wetting.

Important nuance: pull the film at an angle of 15-30° If you pull it perpendicularly, the glue may remain on the matrix. If you remove it, you have small sticky areas, wipe it with a dry microfiber in circular motions.

Napkins and cleaner prepared |Television off and cooled |Film edge treated with liquid |Film shot parallel to screen |Glue residue removed with dry napkin-->

On Xiaomi TV models with a glossy matrix (for example, Xiaomi TV Q2), never use isopropyl alcohol - it leaves murky wiggles that cannot be removed without professional polishing.

Method 2: Steam method (for "old" film)

If the film has been on the screen for more than a month, the glue has time to crystallize, in which case hot steam will help, it softens the adhesive layer without mechanical action.

• 🚿 Steam generator or iron with steaming function (alternative - pot with boiling water).
• 🧽 Rubber gloves: so as not to burn and leave fingerprints on the screen.
• 📏 Plastic spatula (e.g., guitar mediator).

Step-by-step:

1. Heat the water in the steam generator or pour boiling water into the container.
2. Hold the steam source 10-15 cm from the screen for no longer than 5 seconds in one area, so as not to overheat the matrix.
3. Now, you put a plastic blade on the edge of the film and pull it, and the steam softens the glue, and the film is taken off with a whole piece.
4. Repeat the procedure for each corner if the film has not moved away completely.

The advantage of the method is that the steam penetrates the film and dissolves the glue, minimizing the risk of tearing. However, be careful with the Xiaomi TV A2 and Redmi TV X65 models - their matrices have a thin anti-reflective coating that can become cloudy from high temperatures.

⚠️ Note: Do not direct the steam stream to IR-The receiver (usually located down the center) can disable the remote control.

After filming, allow the screen to cool for 10-15 minutes before turning on. If there are white divorces, wipe them with a napkin dipped in distilled water (not in the cleaner!).

Method 3: Use of specialized tools (for complex cases)

If the film is taken in pieces, leaving sticky marks, you need professional formulations.

How to use:

1. Apply the product to the edge of the film with a cotton swab.
2. Wait until the time is set (do not exceed!).
3. Carefully tuck the tape and pull it. If it doesn't respond, repeat the application.
4. After removal, wipe the screen with a dry microfiber, then a wet wipe with a cleaner.

The 3M Adhesive Remover performed better on tests but has a pungent odor - use it in a ventilated room.WD-40 is faster acting but can leave greasy traces that are difficult to remove from glossy screens.

5. Common Mistakes and How to Avoid Them

Even experienced users sometimes make mistakes that damage the screen, and here are the most common ones:

• 🔪 Sharp objects: knives, blades, or scissors scratch the anti-reflective coating, and replacing the matrix will cost 30 to 70 percent of the cost of a TV.
• 🧴 Alcohol solutions: they destroy oleophobic coating, which causes the screen to quickly get dirty.
• ☀️ Direct sunlight: if you shoot the film in the sun, the glue hardens faster than you can remove it.
• 💦 Excess liquid: If a cleaner gets inside the TV through the vents, it can cause a short circuit.

Another common problem is the rainbow effect after film is taken, which occurs when there are microscopic glue particles on the matrix that refract light, and to avoid that, after filming, light the screen at a 45° angle with a flashlight, which is how you see all the contamination.

⚠️ Attention: On Xiaomi TVs OLED (for example, Xiaomi TV Master OLED) Never use abrasives. Their matrices have a super-thin coating that can easily be damaged even with a soft wipe with dust particles.

If after all the manipulations on the screen there are divorces, try polishing:

1. Purchased in optics polished paste for glasses (for example, Zeiss Lens Cleaner) apply to dry microfiber.
2. Circular movements with minimal pressure treat problem areas.
3. Remove the leftovers of the paste with a clean napkin.

💡

If the film is not removed well, try to heat it with a hair dryer at a minimum power (distance 20 cm, temperature up to 50 ° C).

6. Screen care after filming

Once the film is removed, the screen becomes vulnerable to dust, fingerprints and scratches, to keep it in perfect condition:

• 🧹 Regular cleaning: wipe the screen with a dry microfiber 1 time per week. Use Xiaomi Screen Cleaner spray to remove greasy spots MJXJSQ01ZM).
• 🛡️ Protective glass: for models under 55" you can order anti-reflective glass (for example, from Spigen). On large TVs, it degrades brightness, so it is not recommended.
• 🌡️ Humidity control: In a room with humidity above 60%, condensation can form on the screen.
• 🎮 Protection from children and animals: if there are small children in the house, set the TV at a height of 1.2-1.5 m from the floor and fasten the bracket.

For models with a Quantum Dot matrix (e.g. Xiaomi TV Q1), avoid long-term static images (channel logos, game menus). This can cause pixels to burn out.

Settings → Picture → Additional settings → Pixel Shift (Incl.)

If you notice that after filming the screen became less bright, check the settings Picture Mode, maybe the Power Saving mode or Movie mode, which reduces the backlight, Optimal settings for home viewing:

Mode: Standard


Brightness: 80-90%




Contrast: 70-80%




Color temperature: Warm (6500K)

💡

After film removal, never use household chemicals (such as Mr. Proper or Cif) to clean the screen. It contains alkalis that destroy the anti-reflective coating in 1-2 cleanings.

7. When to contact the service center

In some cases, self-removal of the film can lead to permanent damage. Contact an authorized Xiaomi service if:

• 🔧 The film was removed, but white spots remained on the screen (this is a sign of damage to the matrix).
• 🖥️ After the removal appeared vertical or horizontal stripes (possibly damaged plumes).
• 💡 The screen became dull or iridescent divorces appeared when turned on.
• 🔌 The TV stopped turning on after the procedure (possibly the liquid got on the board).

The service center uses ultrasonic cleaning and professional polishing pastes that can't be used at home.

If the TV is guaranteed, do not remove the film yourself - this can be regarded as mechanical damage, and the warranty will be canceled. In the instructions to Xiaomi TV, the user must remove the film within 7 days after purchase. If you do not have time, contact the store where you bought the TV for free removal.

To check the warranty status, go to the Xiaomi Warranty Check website and enter the serial number of the TV (located on the box or in the Settings → About TV menu).

FAQ: Frequent questions about film removal from Xiaomi TV