How to connect Xiaomi True Wireless headphones with each other

Owning modern wireless gadgets from Xiaomi gives freedom of movement and eliminates tangled wires, but sometimes users are faced with the unpleasant situation when devices stop working as a single system. Instead of stereo, you hear music on one side only, or the phone sees two different devices instead of the same headset. This is a classic sign of dissynchronization, when the right and left channels lose communication with each other.

Fortunately, most of the time, the problem is solved by software without having to visit a service center. The process of reconnecting between modules requires precise sequence execution, since the pairing algorithm can vary depending on the model and version of the firmware. Ignoring the order often leads to gadgets remaining in mono-operability mode.

In this guide, we will take a look at all the known ways to re-unite modules into a single stereo system. We will look at standard procedures for different series, forced reset methods and the nuances of working with the Mi True Wireless Earbuds application. A careful study of the material will help you return to the full sound of your favorite music in just a few minutes.

Reasons for the desynchronization of the right and left earphone

Before we start to actively restore communication, we need to understand what may have caused the malfunction of the electronics, most often the problem lies in the banal mismatch of Bluetooth communication channels, when one module “forgets” the partner, this can happen after connecting to a third-party device that intercepted control, or after the full discharge of the battery of one of the channels.

Another common cause is software errors in the smartphone operating system or the firmware headset itself, and sometimes the accumulated connection cache causes addressing conflicts, which makes the TWS (True Wireless Stereo) protocol unable to correctly prioritize the master device, in which case the system perceives the left and right sides as independent mono-devices.

Physical factors, such as oxidation of contacts on charging saws inside the case, should not be excluded, if one of the modules did not recharge due to poor contact, it could turn off prematurely and exit the pairing mode, and interference from other Wi-Fi routers or microwave ovens can in rare cases break the bridge between the channels.

• 🔋 Complete discharge of one of the modules and loss of memory about (conjugation).
• 📱 Bluetooth profile conflict after switching between different smartphones.
• 📡 Microcode software failure requiring system restart.
• ⚡ Oxidation of contact sites leading to uneven charge.

⚠️ Attention: If one of the headphones emits intermittent cracking or no signs of life at all even after a long charge, the problem may be hardware.

Preparation for the re-establishment procedure

The success of the channel reconnection operation depends on proper preparation, and the first step is to completely disable Bluetooth on all devices that have previously been used with this headset, which will prevent automatic reconnection during the setup process, which often knocks down the synchronization algorithm.

Next, visually inspect the charging contacts, which should be free of dust, pile or oxides, wipe the contacts with dry lilaless cloth or cotton swab slightly soaked in alcohol, make sure that both modules sit tightly in the case and the indicators are on, signaling the charging process.

It is also important to clear the list of stored devices in your smartphone. Find your model in your Bluetooth settings, click on the gear or information icon, and select the option “Forget device” or “Delete” This is a critical step, since old profiles may contain erroneous configuration data of the stereo pair.

After doing this, leave the headset in a closed case for 10-15 minutes, which will allow the power management system to stabilize and prepare for the next initialization cycle, and then you can move on to the direct process of combining.

Universal method of pairing for all models

There is a basic algorithm that works for the vast majority of Redmi AirDots, Mi True Wireless Earbuds and Xiaomi Buds models. It is based on manually starting the mode (pairing) simultaneously on both modules. First remove both devices from the charging case.

Wait for the lights to light up. They usually flash white or red to signal readiness, and at this point, it's important not to try to connect them to your phone. Your job is to get them to "find" each other, and you need to touch the touch areas on both headphones at the same time and hold your fingers for about 5-7 seconds.

At the moment of retention, the indicators should go out, and then start flashing quickly, often changing the color or frequency of the flashes. This means that the partner search mode is started. Once one of the modules (usually the right one) becomes a master device, the display on it becomes rare, and on the second one it will go out or flash slowly.

Sequence of action:


1. Remove both modules.




2. Turn off Bluetooth on your phone.




3. Hold the sensors for 5-7 seconds before changing the blinking mode.




4. Turn on Bluetooth and perform a search.

Specifics of setting up different Xiaomi and Redmi series

Despite the common platform, different product lines may have unique pairing features. For example, the Redmi AirDots series often requires longer sensor retention (up to 10-12 seconds) to activate TWS-pairing. At the same time, the flagship Mi True Wireless Earbuds Basic 2 can sync automatically immediately after being pulled from the case if they have previously been paired.

Active noise cancelling models such as the Xiaomi Buds 3 Pro or Buds 4 often use more complex algorithms, and it is critical that at least 20-30% of the charge remain in the case, otherwise the system may not start the recovery procedure, in which case it is recommended to connect the case to charging before starting manipulation.

Below is a table that systematizes the features of popular models, which will help you choose the right tactics.

Understanding the specifics of your model avoids unnecessary repetition and achieves the desired result faster. If standard methods do not work, you should refer to the manual of a particular series.

Use of Mi Home and Xiaomi Earbuds

For owners of the Xiaomi ecosystem, a powerful diagnostic and customization tool is specialized software. The Xiaomi Earbuds app (or integration via Mi Home) allows not only to manage functions, but also to forcefully initiate a reconnection or firmware update, which often solves the problem of desynchronization.

Once you have at least one headphone on your smartphone, open the app. If the system sees both devices but they don't work in stereo, try to find firmware Update. Even if the version is up to date, the re-routing firmware can overwrite the configuration files that communicate between channels.

Some models have a feature called "Settings Reset" or "Factory Reset" that does the same thing as manual sensor clamping, but more reliably, and you can check the channel balance through the app to make sure that the sound has not migrated completely to one speaker due to a software error.

• 📲 Download the official Xiaomi Earbuds app from Google Play or App Store.
• 🔌 Connect your headphones to your phone in mono mode (at least one channel).
• 🔄 Check for firmware updates in the device menu.
• ⚙️ Use the built-in resetting feature if available.

⚠️ Note: During the update of the firmware through the application, it is strictly impossible to remove the headphones from the case or remove the smartphone. Interrupting the data recording process can lead to complete inoperability of the device ("bricking»).

Forced reset (Hard Reset) of headphones

If the soft methods didn't work, the last and most powerful argument is a full reset to the factory settings (Hard Reset), which erases all memory of previous connections and returns the logic of the controller to its original state.

Make sure the case cover is open and the devices are charging (indicators are on fire). Find a function button on the case case case (if any) or prepare for long-term sensor retention on the ears themselves. If there is no button on the case, press the sensors on both headphones simultaneously and hold for about 20-30 seconds, even if they turn off.

The indicators should flash several times (usually 3-5 times) or change color to orange/red, then go out. This is a signal that the configuration memory is cleared. Then close the case, wait 10 seconds, open again and try to re-do the standard pairing procedure.

💡

Hard Reset is a radical, but often the only way to fix deep software bugs that block your work. TWS-protocol.

After reset, be sure to remove the old device from the phone’s Bluetooth menu before the new connection to avoid encryption key conflicts.

Frequently Asked Questions (FAQ)

💡

To extend the battery life, try not to keep the headphones in a discharged state for a long time. Lithium polymer batteries degrade faster if the voltage drops below a critical level.