How to tie Xiaomi headphones to each other: full instructions

Modern wireless headsets from Xiaomi and the sub-brand Redmi have gained popularity due to their affordable price and compact size, but they have a specific feature in their work. Users often face a situation where one earphone stops seeing the second one, and sound is played in only one ear or on different devices at a time. This is not a breakdown of electronics, but a failure of logical communication between modules that requires manual intervention to restore.

The process of how to tie shaomi headphones together is technically called mating. TWS-Unlike traditional Bluetooth devices, the right and left channels first connect to form a single network, and then act as a single device for a smartphone.

In this article, we will analyze the algorithms of actions for various models, from classic AirDots to new Buds. We will consider methods of software cleaning of the headset memory, hardware reset through touch panels and the nuances of working with the Mi Wear application. Proper execution of the sequence of actions guarantees stable operation of the stereo pair.

Why the headphones stop working in pairs

The main reason for desynchronization is the break of communication during discharge or extraction from the case. When you put the headset in the charging box, it goes into standby mode, but if one of the modules is discharged faster or contact with the charging pins was broken, the second headphone can “forget” the partner. MAC-search-place.

Another common problem is Bluetooth signal conflicts: If there are many active devices in sight, or if the previous gadget that the headphones were connected to tries to restore communication, this can bring down connection priorities, and a software glitch in the firmware of the earpiece itself, which is solved only by a complete reboot of the logic of the work, also affects.

Physical factors play a role, too, and oxidation of contacts, moisture or sulfur in touch areas can lead to false positives or, conversely, blocking functions, which is why you need to make sure that the device is clean before you start restoring procedures.

⚠️ Note: If one of the headphones is completely discharged (0%), it will not be able to participate in the mating process.

Often users confuse desynchronization with a break in the speaker. To check this, just put both earphones in the case, close the lid and wait 10 seconds, then pull them out at the same time. If the problem persists, then forced re-teaming is required.

Preparation for the synchronization procedure

Before you start the technical part of the process, you need to prepare the environment and the device itself. The first step is to clear the list of paired devices on your smartphone. Find your model name (e.g. Redmi AirDots or Mi True Wireless Earbuds) in your Bluetooth settings and click on the "Forget the device" or "Disable" button, which will remove the old encryption keys that may interfere with the new setup.

Next, make sure that the Bluetooth on the phone is temporarily disabled, which will prevent automatic connection during the setup process, and it is also recommended to close background applications that use audio, such as navigators or messengers, to free up the resources of the Bluetooth module of the smartphone.

It's important to check the case charge. If the charger doesn't light up when you put the headphones inside, maybe the contact problem is, wipe the metal pads on the headphones and inside the case with a dry lilaless wipe, and the cleanliness of the contacts is key to successful charging and correct determination of the status of the device.

• 🔌 Make sure the case is charged at least 30-40% for stable operation.
• 📱 Turn off Bluetooth on your smartphone before starting the reset procedure.
• 🧼 Wipe the touch areas and charging contacts with dry cloth.
• 🚫 Remove the headphone profile from the phone’s memory (“Forget the device»).

Reset method through touch panels (TWS-model)

The most common way to tie your shaomi headphones together for AirDots, Redmi AirDots and early Mi True Wireless is to use touch buttons, which do not require a physical button on the case and run directly on the modules themselves.

Take both of the headphones out of the case. If they're on and blinking, you need to turn them off. To do this, press the touch areas on both of the headphones simultaneously and hold them for about 5 to 7 seconds until the lights go out. Now, when the devices are off, start clamping the sensors again. This time, hold them for much longer -- about 20 to 30 seconds -- you'll see the lights light up red, then flash white, and at some point they'll flash red several times in a row. This is a signal that there's been a reset on the internal memory and a cleanup.

Once the lights are gone, put the headphones back in the case. Wait 5-10 seconds for them to lock into the charging contacts. Then pull them out again. Now they have to go into pairing mode. Usually one headphone (most often the right one) will flash white quickly, and the second will flash slowly or not at all, waiting for a connection. When they find each other, the blinking will stop or become rare (once in a few seconds).

⚠️ Warning: During prolonged clamping (20-30 seconds), do not release your finger, even if the earphone vibrates or sounds.

In some modifications, such as AirDots 2 or Essential, the algorithm may be slightly different: after shutting down, you need to pinch the sensors and hold them until a double or triple red flash. The key here is to patiently wait for a series of signals to confirm the cleanup.

Synchronization of models with a button on the case

Newer models, such as the Mi True Wireless Earphones 2, 2S, 2 Basic and Air 2, feature a physical button on the charger case, which makes it much easier to tie the headphones together, since it does not require complex manipulation of the timing of the presses on the headphones themselves.

Place both earbuds in the charge case and leave the lid open. Find a round button on the case (usually located between the headphone compartments or on the end). Press and hold this button for 7-10 seconds. The indicator on the case (usually white or orange) will flash quickly, signaling the transition to pairing mode.

Once you release the button, the headphones inside the case can flash. Close the lid and wait a few seconds, then open it again. If the headphones flash in sync or are on even light (depending on the model), then they are paired. You can now turn on Bluetooth on your phone and search for the device.

For the Air 2 Pro or 3 Pro series, the procedure is similar but may require the Mi Wear app to be fully calibrated, but the basic pairing of the left and right channel is always done through a button on the case.

💡

If the button on the case is pressed too easily and doesn't have a characteristic click, it may have caught fire. Carefully press it several times in a row to develop a mechanism.

Use the Mi Wear app to customize

For Android and iOS smartphone owners, the official Mi Wear app (formerly Mi True Wireless) is an excellent diagnostic tool, which allows not only to manage settings, but also to force a reconnection or update the firmware, which often solves the problem of desynchronization at the software level.

Once you have resetted with one of the methods described above, connect the headphones to your phone as a new device. Then open the Mi Wear app. If the headphones are correctly identified, you will see their image and the charge level of each channel separately. The settings menu often has a "Find Headphones" or "Connection Check" option, which helps make sure that the left and right channels see each other.

One of the key features of the app is to update firmware. If an available update is displayed on the list of devices, be sure to install it. Manufacturers often release patches that fix Bluetooth protocol errors, which cause communication between modules to break, the update process takes several minutes, during which time the headphones must be near the phone.

You can also reset your settings to factory settings through the software menu if the physical buttons don't work. Go to the device settings (three dots or a gear) and select Reset or Unpair, which will send a command to clear the memory of the headphones.

💡

The Mi Wear app is the only way to check each headphone’s firmware version separately and update them, which often solves the problem of desynchronization.

Typical problems and ways to solve them

Even if you follow all the instructions, you can get complicated. One of the common problems is phantom connectivity. The phone sees two devices with the same name (like two Mi AirDots), in which case you need to remove both devices from the Bluetooth list, turn off the Bluetooth on the phone, put the headphones in the case, reset, and then turn on the search again.

If you only have sound in one headphone, check the balance of sound in the phone settings. Sometimes after you reconnect, the system balance shifts one way. The way to check is: Settings → Sound and vibration → Balance. Make sure the slider is strictly in the center.

In the case when the headphones are not in pairing mode (do not blink), try discharging the case completely, and then charging it to 100%.This can restart the power controller inside the case, which controls the logic of charging and resetting.

• 🔊 Check the channel balance in the smartphone sound settings.
• 🔄 Remove all old “Mi AirDots” profiles from your phone’s memory.
• 🔋 Completely discharge and charge the case to reset the controller.
• 📶 Keep your phone at a distance of no more than 1 meter during setting up.

⚠️ Warning: Don't try to connect your headphones if they're connected to different audio sources. Make sure both modules are free from communication with other gadgets.

FAQ: Frequently Asked Questions