Wireless speakers often face a situation where one of the ears stops working or devices lose communication with each other, a common problem for the entire True Wireless Stereo line, which is solved by software resetting. Understanding how to reconnect the Xiaomi Mi True headphones will allow them to restore functionality in a few minutes without contacting the service.
The process of restoring communication depends on a particular model, whether it is Mi True Wireless Earbuds Basic, AirDots or more advanced versions of Air 2. In most cases, it is enough to perform a forced reset to erase the old pairing data from the memory of the gadgets, after which they will go back to search mode and can connect to the smartphone as new devices.
Below we will discuss in detail all the preparation steps, reset methods for different modifications and how to eliminate typical synchronization errors. It is important to carefully monitor the indication, since it is the blinking of LEDs that indicates the current status of the operation. Proper execution of the sequence of actions ensures the successful recovery of your acoustics.
Preparation for reconnection and discharge
Before any manipulations are initiated, make sure that the device’s battery packs are at least 30-40% charged. Low charge can cause the reset process to be interrupted halfway, causing a software failure of the Bluetooth controller. Put both ears in a charging case and leave them there for 15-20 minutes, even if the indicators indicate the presence of power.
Clean the charging contacts on the headphones themselves and inside the case with a dry cotton swab. Oxidation or dust can prevent the correct transfer of energy and synchronization signals between modules. Clean contacts are the basic condition for stable operation of any TWS-A product that users often forget about.
It is also recommended to remove the old device from the Bluetooth list on your smartphone. Go to the wireless network settings, find the name of your model (for example, Mi True Wireless EBs). Basic_R) and select "Forget" or "Cancel pairing" to eliminate address conflicts when reconnecting.
⚠️ Warning: Do not try to reset if one of the ears is completely discharged. First, provide stable power to both modules, otherwise synchronization between the left and right channel will not occur.
☑️ Preparation for discharge
Universal method of resetting through touch panels
The most common method, which is relevant for most models, including the Redmi AirDots and the basic versions of Mi True, involves using touch zones. You need to remove both earphones from the charging case. Make sure they are on (usually they turn on automatically when removed).
Press and hold the touchpads on both headphones simultaneously. Hold for about 5-7 seconds until the indicators start flashing red. Once red light comes on, release your fingers and press the sensors again, holding them for about 20 seconds, at which point the indicators should flash white several times, signaling a successful reset.
After a successful operation, the devices will shut down. Put them back in the case, close the lid and wait 10 seconds. Then remove them again - they should automatically enter pairing mode, and the indicators will flash quickly white, waiting for a connection to the phone.
- 🔹 Remove both modules from the case at the same time.
- 🔹 Hold the sensors on. 5-7 second-light.
- 🔹 Release and again press for 20 seconds before white blinking.
- 🔹 Put it in the case to reboot the system.
💡
If you don’t work out the first time, try pinching the sensors with a little more effort, but without fanaticism, to ensure tight contact between your finger and the sensory area.
Specificity of reset for models with a button on the case
More advanced models, such as the Mi True Wireless Earphones 2, Air 2S or Air 2 Pro, feature a physical control button on the charging case itself. This simplifies the process significantly, as it does not require precise hitting on the sensors on the ears. First, place both earbuds inside the case and leave the lid open.
Find a circular button on the case (usually located on the end or front panel). Press and hold it for 15 seconds. The status indicator on the case will flash white, signaling the transition to reset mode. Release the button when the blinking becomes intense or changes color, depending on the specific modification.
Then close the case cover for 5-10 seconds, and then open it again. The headphones should go into pairing standby mode. The name of your headset will appear on the smartphone screen in the list of available devices. Click on it to complete the communication.
What to do if the button does not respond?
It's important to note that when using this method, the synchronization between the left and right channel is inside the case, so it's critical that both devices are inside and have contact with the charging contacts at the time of pressing the button.
Standby mode and search for a smartphone device
After the reset procedure, your Mi True headphones go into a state ready for a new acquaintance, at which point they look for any device with active Bluetooth, open the settings on your phone and enable wireless data transfer.
The list of available devices should show the name of your headset if you see two identical names (e.g. Mi True Wireless EBs). Basic_L and... R), which means that the headphones are not synchronized with each other, in which case you need to repeat the reset procedure, paying special attention to simultaneously pressing the sensors.
If you connect successfully, only one device name will remain on the list. Click on it. The communication process usually takes no more than 5-10 seconds. Once connected, the voice assistant will inform you of the status (for example, Connected or Right Channel), and the music track can automatically start.
| Model headphones | Type of management | Indication of discharge | Retention time |
|---|---|---|---|
| Mi True Earbuds Basic | Sensor on the ear | Red -> White | 5 sec + 20 sec |
| Redmi AirDots | Sensor on the ear | Red -> White | 5 sec + 20 sec |
| Mi True Wireless 2 | The button on the case | White flashing | 15 seconds. |
| Mi Air 2S | The button on the case | White flashing | 15 seconds. |
Problem Solving: Only one ear works
When sound comes from only one earbud, it is the most common reason users are looking for reconnection information. TWS-True Wireless Stereo, and phones perceive ears as two independent mono-devices instead of one stereo pair.
To correct this error, you need to completely reset the memory of both modules. First remove the device from the phone's Bluetooth menu. Then place both earphones in the case, close the lid and wait 10 seconds. After that, complete the reset according to the instructions for your model (sensors or case button).
Key point: Don't be in a hurry to connect to your phone after the reset. Give the devices 5-10 seconds to stand in the air (outside the case) so they can find each other and create an internal network. Only when one of the ears stops flashing (or blinks less often) and the second continues to search quickly, you can turn on Bluetooth on your smartphone.
⚠️ Note: If two devices with the same name appear in the Bluetooth list after reset, do not connect to either. repeat the reset as the stereo pair has not formed.
Sometimes, serial connectivity helps: connect to one device on the list first, wait for the connection, and then try to connect the second one. However, for Xiaomi models, it is better to get one name to appear in the list through a reset.
Using the Mi Earbuds app for diagnostics
For owners of Xiaomi and Redmi smartphones with a shell MIUI or HyperOS, advanced functionality is available through the system menu. When you connect compatible headphones on the screen, a window with animations and the charge level of each ear often pops up on the screen. This is a built-in analogue of the Mi Earbuds application.
If the standard connection doesn't work, you can try to find the Mi Earbuds app in GetApps or Google Play, which not only tracks your charge, but also checks for firmware updates. Often, the connection problems are solved by installing the current version of firmware.
The app also has headphone search and control settings. If the reconnection is successful but the sound is quiet or interrupted, check in the app if the Low Latency mode is activated, which can consume more resource and cause interference in congested air.
💡
The most reliable way to fix the desynchronization of the left and right channel is a complete reset, followed by deleting the device from the phone’s memory before re-pairing.