Xiaomi’s modern humidifiers are not just appliances, but full-fledged elements of the smart home ecosystem. Xiaomi Smart Anti-Dry Humidifier 2 (often referred to simply as Humidifier 2) features advanced functionality, including the ability to remotely control via a smartphone. Properly configured the device opens access to scenario automation, water flow monitoring and fine-tuning the humidity level in the room.
The initial activation process may seem complicated only at first glance, especially if you have not previously encountered a brand product. However, following a clear algorithm of actions, you can integrate the device into the Wi-Fi network in minutes. It is important to understand that the stability of the gadget depends on the quality of the configuration at the initial stage.
In this article, we will take a closer look at all the steps of connection, from unpacking to fine-tuning through the Mi Home app, and learn how to avoid common errors related to wireless network frequency and how to reset the module settings correctly if the device loses communication with the server.
Preparation for setup and network requirements
Before starting the procedure, you need to make sure that your mobile device and the humidifier itself are in the zone of confident reception of the router signal. The wireless frequency is critical: the Wi-Fi module in Xiaomi humidifiers operates exclusively in the 2.4 GHz band. 5 GHz networks are not supported, and trying to connect to them will lead to an error during the search phase of the device.
⚠️ Note: If your router broadcasts a single network with a common name (SSID) For both frequency bands, the application may not correctly identify the device, in which case it is recommended to temporarily separate the networks in the router settings or turn on the guest network with only the 2.4 GHz protocol for the time of setting up.
If you plan to use voice control via Google Assistant or Amazon Alexa, make sure that the regions of the accounts are the same or correctly connected. Geolocation services (GPS) must be enabled to work on all functions on the smartphone, as the Android and iOS operating systems require this for scanning devices.
Don’t forget to check the package: in the box with Xiaomi Humidifier 2 should be a power cable, instruction and the tank itself. Before connecting to the power grid, be sure to remove all transport films and packaging from the internal elements, especially from the float and water level sensors.
Installation and configuration of the Mi Home application
The control center of your humidifier will be the official Mi Home app (or Xiaomi Home), you can download it from the official App Store or Google Play stores. After installation, you must undergo the registration or authorization procedure.
In the upper right corner of the app's home screen is a region icon. Devices purchased in China often require a "China" region, while global versions (Global Version) are better suited for "Russia", "Germany" or "Singapore", and the wrong choice of region can lead to the device simply not appearing on the list available for addition.
After authorization, go to the Devices tab and click the Add a new gadget button (usually this is an icon «+» The app will run the scan. QR-And you can find the bluetooth devices in range, and make sure that the Bluetooth on the phone is on, and that's going to speed up the detection process.
💡
Use the same region in the Mi Home app and in your Mi Account profile. Changing the region in the app settings resets the list of devices and scripts.
Step-by-step instructions for connecting the humidifier
When the prep phase is complete, you can go to direct pairing. Take the power cable that comes with the kit and plug it into the connector on the back of the device and then into the socket. Once the power is turned on, the humidifier will go into standby mode, and the mode indicator will flash or burn in orange, signaling readiness for setting.
Open the Mi Home app and wait for a pop-up to suggest adding a new device. If automatic detection fails, click "+", select the Humidifiers category and search the Xiaomi Smart Anti-Dry Humidifier 2 list (the model may be labeled zhimi.humidifier.ca4 or similar).
☑️ Checklist before connection
Follow the instructions on the screen: the app will ask you to confirm that the indicator on the device is flashing. If so, click "Yes." Then you will need to enter the password from your Wi-Fi network. Be careful when entering the password, since the keyboard can automatically switch to capital letters.
As you set up, the phone will transmit network data to the humidifier, at which point the smartphone screen may go out or a message will appear about connecting to the device's network - do not interrupt the process. Once the data is successfully transmitted, the humidifier will emit an audible signal, and a window will appear in the application with the name and room.
⚠️ Note: During the transmission of data about Wi-Fi, keep the smartphone at a distance of no more 1-2 Interrupting communication at this point can lead to a configuration error, and the procedure will have to start again.
Table of indicators and operating modes
Once connected, it is important to learn how to read the status of the device by indicators. Xiaomi Humidifier 2 is equipped with an informative LED panel that reports on the current mode, water level and communication status.
| Indicator/Color | Mode of work | Description of the state |
|---|---|---|
| Green (constantly) | Normal work. | The humidity level corresponds to the given, the water is normal. |
| Orange (constantly) | Standby regime | The device is on but not working (sleep or manual stop) |
| Red (flashing) | Low water level | Water must be added to the tank. |
| Blue (blinks) | Interconnection mode | The device is ready to connect to the Wi-Fi network |
| yellow | Sterilization regimen | Activated water treatment mode (if supported by the model) |
Understanding color indications allows you to quickly diagnose problems without having to open an application, for example, if you see a flashing red light, it is an unambiguous signal of maintenance, ignoring which can lead to a failure of the pump.
💡
The green color of the indicator is the normal mode of operation. Orange or red require your intervention or checking the settings in the application.
Setting up scenarios and automation
The main advantage of a smart humidifier is that it can work without human intervention. In the Mi Home app, go to your device settings and select Automation or Scenarios, and you can create rules where the humidifier will turn on or off.
The most useful scenario is to bundle with a humidity sensor (if it is built into the model or bought separately), you can ask the condition: "If the humidity is below 40%, turn on the humidifier", and "If the humidity is above 60%, turn off" This allows you to maintain the perfect microclimate and save energy.
Scheduling is also available, for example, you can program your device to work only at night with a reduced fan speed to run silently, using the Timer feature or creating a time-based script.
⚠️ Warning: Do not set your humidity target below 30% or above 70%. Too low humidity is not effective for health, and too high can lead to condensation on windows and mold in the corners of the room.
For advanced users, integration with other devices is available, such as setting a scenario: "When the smart lock opens (I came home) and below-normal humidity, turn on the humidifier for 15 minutes," which makes running the house really smart.
Secret functions in the engineering menu
Solution and resetting of settings
In the process of operation, you can experience situations when the humidifier stops responding to commands or disappears from the network, most often this is due to a change in the parameters of the router or updating the firmware. The first step should always be to restart the device: disconnect it from the network for 10-15 seconds and turn it on again.
If the device does not connect to Wi-Fi, check whether the router is not enabled filtering by MAC-Also try to temporarily disconnect. VPN on a smartphone, as Xiaomi servers can block requests from regions when the tunnel is active.
To completely reset the network settings, the Xiaomi Humidifier 2 housing has a reset button (usually combined with the on button or located separately). Press and hold this button for 5-7 seconds until the Wi-Fi indicator flashes quickly.
If the problem persists, check for firmware updates in the app. Manufacturers regularly release patches that fix connection stability errors. Go to your device settings, click three dots in the corner, and select "Verify Updates."