Connecting a robot vacuum cleaner Xiaomi to Wi-Fi via Android: instructions 2026

Xiaomi’s robot vacuum cleaners have long been an integral part of the smart home, but they can’t work without a stable Wi-Fi connection. Without them, you can’t control your device through the Mi Home app (or Dreamehome for Dreame models), set up a cleaning schedule or receive status notifications. However, many users face difficulties when they first connect: a vacuum cleaner “can’t see” the network, an application gives an error, or the process gets stuck in the interface phase.

In this article, we will look at all the possible ways to connect Xiaomi’s robot vacuum cleaner to Wi-Fi via an Android smartphone, including Mi Robot Vacuum, Dreame, Viomi, and others. We will focus on common errors (such as Error 1006 or Connection failed) and how to fix them. If you have tried to connect but failed, check the section with alternative methods, which describes the workarounds for stubborn devices.

Note: the instructions are relevant for firmware in 2022-2026. If your vacuum cleaner is released before 2018 (for example, Mi Robot Vacuum 1), some steps may differ - see the section for outdated models.

1.Preparation: What to check before connecting

Before you start setting up, make sure that all conditions are met, which will save time and eliminate most errors.

✅ Requirements for Wi-Fi network:

• 📶 Frequency 2.4 GHz: Xiaomi robots do not support networks 5 GHz (even if your router is dual-band) If the router's settings enable Auto mode (2.4G/5G), temporarily 5 GHz or create a separate network for 2.4 GHz.
• 🔒 Type of encryption - only WPA2-PSK (AES). Networks with WEP, WPA3 Open (without password) is not supported.
• 📵 Absence of “black” characters – Wi-Fi password should not contain Cyrillic, spaces, signs!@#$% Or emoji. Use Latin and numbers.
• 🌐 Router Region – If you are in Russia, make sure that your router settings are Russia or Europe.Some Chinese vacuum cleaners block connections to China outside of China.

✅ Requirements for a smartphone:

• 📱 Android version - not lower than 6.0 (for stable operation Mi Home recommended 8.0)+).
• 📲 Permissions – Mi Home (or Dreamehome) must be granted rights to Geodata, Wi-Fi, and Bluetooth.
• 🔄 Turn it off. VPN — Some Xiaomi servers are blocking connections due to geo-restrictions.

⚠️ Note: If you use a guest or customer-isolated network (such as a hotel), the vacuum cleaner will not be able to connect. MAC-filter or filter by device.

2. Step-by-step instruction: connection via Mi Home

This method is suitable for most Xiaomi models, including Mi Robot Vacuum-Mop 2 Pro, Dreame D9 viomi V3. If you have a Dreame brand vacuum cleaner, use the Dreamehome app – the algorithm is similar.

🔹 Step 1: Installation of the application

1. Download Mi Home from Google Play (or APKPure if the app is not available in your area).
2. Sign up or sign in through your Xiaomi account (if not, create a link).
3. Select the region of Russia (or Europe) in the profile settings.

🔹 Step 2: Adding a device

1. Click + → Add the device in the upper right corner.
2. Select the category Robot vacuum cleaner.
3. Find your model in the list (e.g. Mi Robot Vacuum-Mop 2 Lite). If there is no model, choose Another.

🔹 Step 3: Vacuum-to-vacuum coupling

1. Make sure the vacuum cleaner is on and near the smartphone (up to 1 meter away).
2. Press the Wi-Fi (or Reset) button on the vacuum cleaner for 3-5 seconds until you hear an audible signal (usually a voice message "Waiting for connection").
3. In the application, click Next and wait until the vacuum cleaner emits a second signal (confirmation of readiness for connection).

🔹 Step 4: Connect to Wi-Fi

1. Select your 2.4GHz network from the list.
2. Enter your password (check the register!).
3. Click Connect and wait until the process is complete (may take up to 2 minutes).

✅ If everything goes well, the vacuum cleaner will issue a voice message (for example, "Wi-Fi connected"), and the application will appear his card with the status of Online.

3. Typical errors and their solutions

Even with the right setup, the connection can end in error, and let's look at the most common error codes and how to fix them.

⚠️ Warning: If after several attempts the vacuum cleaner has stopped responding to buttons or emits a constant beep, reset to factory settings. To do this, press the power and Wi-Fi buttons simultaneously for 10-15 seconds until you hear a double beep.

💡

If your router supports a guest network, try connecting a vacuum cleaner to it – sometimes this solves problems with locking devices with the main network.

4. Alternative methods of connection

If the standard method didn't work, try one of the alternative methods.

• 🔄 Mi Home app doesn't see vacuum cleaner.
• 📵 Vacuum cleaner emits Error 1006 error despite correct password.
• 🌍 You are in a restricted region (e.g. China, where a Chinese account is required).

🔹 Method 1: Connect via the access point (Hotspot)

If the router blocks the vacuum cleaner, create an access point on your smartphone:

1. On Android go to Settings → The Internet and the Internet → Access Point and modem.
2. Enable Wi-Fi Access Point and set a password (Latin only) + figure).
3. Connect the vacuum cleaner to this network via Mi Home.
4. After a successful connection, return to the main network (in the app, select Change Wi-Fi network).

🔹 Method 2: Manual addition through IP-address

For experienced users:

1. Connect your smartphone to the same 2.4GHz network you want to connect the vacuum cleaner to.
2. Find out. IP-vacuum cleaner address (usually it communicates it by voice when turned on or it can be found in the router in the list of connected devices).
3. In the smartphone browser enter http://[IP-vacuum address] (e.g, http://192.168.1.100).
4. In the control panel that opens, select Wi-Fi Settings and enter network data manually.

🔹 Method 3: Use of third-party applications

If Mi Home is not working, try:

• Mi Home Lite is a simplified version of the official app.

5.Configure after connection

After a successful Wi-Fi connection, it is recommended to perform a basic vacuum cleaner setup to avoid problems in the future.

🔹 Firmware update

Outdated firmware can cause connection errors.

1. Open the vacuum cleaner card in Mi Home.
2. Go to Settings → Update firmware.
3. If a new version is available, click Update and wait until it is completed (don’t turn off the vacuum cleaner!).

🔹 Room binding

For the correct operation of the cleaning card:

1. Go to Settings. → Map.
2. Select Add a floor plan and follow the instructions (the vacuum cleaner must drive around the perimeter of the room).
3. Save the map and mark the cleaning areas.

🔹 Scheduling

To clean the vacuum cleaner automatically:

1. In the device card, select the Schedule.
2. Add a new task, specifying the days of the week and time.
3. Choose the type of cleaning (dry, wet or full).

⚠️ Note: If you use multiple routers on the same network (e.g., a Mesh system), make sure the vacuum cleaner is connected to the main router. Some Xiaomi models lose communication when switching between Mesh nodes.

💡

After the first connection, be sure to check the server region in the vacuum cleaner settings (in Mi Home).If China is specified, change to Russia or Europe, otherwise some of the functions may not be available.

6. Connecting legacy models (until 2018)

Xiaomi vacuum cleaners of the first generation (for example, Mi Robot Vacuum 1 or Mi Robot Vacuum) 1S) You may need additional action due to outdated firmware.

🔹 Features of connection:

• 🔌 These models do not support networks with encryption WPA3 — only WPA2-PSK.
• 📡 There may be problems with routers that are enabled 802.11n Only - try to switch the mode to 802.11b/g/n.
• 🌍 For Chinese versions of vacuum cleaners (CN In the model name, you may need a Xiaomi account with the region of China.

🔹 Instructions for Mi Robot Vacuum 1:

1. Download the old version of Mi Home (e.g. 5.6.41) from APKPure.
2. Register a Xiaomi account with the region of China (use your phone number) +86).
3. When you add a device, select China as the server region.
4. If the vacuum cleaner doesn’t connect, try using the developer mode (press the Home button for 5 seconds until the indicator blinks).

🔹 Firmware through Valetudo (for advanced ones)

If the official methods do not work, you can install an alternative firmware:

1. Unlock the vacuum cleaner through SSH (Root access to router required to intercept token).
2. Install Valetudo according to the instructions.
3. Once installed, the vacuum cleaner will work without Xiaomi’s cloud, but will lose some of the features (such as voice control).

7. Frequent questions and answers