Step-by-step connection of the robot vacuum cleaner Xiaomi G1 to the phone on Android: instructions with pictures and tips

The Xiaomi G1 robot vacuum cleaner is a smart device that makes cleaning your home much easier, but it only works when you sync it properly with your smartphone. Many users have difficulty connecting: the app doesn't see the vacuum cleaner, the Wi-Fi doesn't connect, authentication errors occur. This article will help you avoid typical problems and perform the setup the first time.

We will discuss the connection process in stages, from the preparation of the phone to the final setting of the cleaning schedule. Particular attention will be paid to common errors (for example, why the Mi Home does not find the device) and how to fix them. The instructions are relevant for all versions of the Xiaomi G1, including versions that support Mi Home and Xiaomi Home (formerly Mi Home). If you have a different model of the Xiaomi robot vacuum cleaner, some steps may differ, check compatibility in the documentation.

Before you start, make sure your smartphone meets the minimum requirements: Android 6.0 or later, having a Wi-Fi module (2.4 GHz) and at least 500 MB of free memory to install the app. Also check that the robot vacuum cleaner is at least 30% charged - this is critical for the first turn on.

1. Preparing the phone and robot vacuum cleaner for connection

Before synchronization, several preliminary steps must be performed, and neglecting them often leads to application failures or the inability to detect the device.

First, update your smartphone firmware: go to Settings → System → Software Update and install the latest patches. This is important, as older versions of Android can conflict with the Xiaomi Home app. Then check the permissions for the app: it must have access to geodata, Wi-Fi and notifications. Without these permissions, connection will be impossible.

Next, prepare the robot vacuum cleaner:

• 🔋 Charging: Connect the device to the base and wait until the charge indicator lights up green (minimum 30% charge.
• 📡 Wi-Fi: Make sure your router supports 2.4GHz. - Xiaomi robot vacuum cleaner G1 Does not work with 5 GHz or 6 GHz networks.
• 🔄 Reset: If the vacuum cleaner has been used before, reset to the factory settings. To do this, press the power button for 10 seconds until the beep sounds.

⚠️ Note: If your router has the same network name for both bands (2.4 and 5 GHz), temporarily divide the networks in the router settings.

We also recommend disabling VPNs and ad blockers on your phone, which can prevent communication with Xiaomi servers. If you use Mi Account from China, create a new account in the region of Russia or Europe - this will make it easier to set up.

2. Installation and configuration of the Xiaomi Home app

The official robot vacuum cleaner control app is Xiaomi Home (formerly Mi Home), which can be downloaded from Google Play or Xiaomi's official website. Avoid third-party sources: fake versions of the app may contain viruses or may not support the latest device models.

After installation, follow the following steps:

1. Open the app and select the region of Russia (or Europe if Russia is not available).
2. Sign in with Mi Account or create a new account if you don't have one. Use a valid email and it will receive a confirmation email.
3. In the main menu, click Add Device (+) and select the Vacuum Category.
4. In the list of models, find the Xiaomi Mi Robot Vacuum G1 (or Xiaomi Robot Vacuum G1 – the name may vary depending on the version of the application).

If your model isn’t listed, upgrade to the latest version of the app or try connecting via another device. → Manual search. In rare cases, scanning may be required. QR-code that is on the bottom of the vacuum cleaner or in the documentation.

3. Connecting a robot vacuum cleaner to Wi-Fi

This is the most critical stage where users are most likely to encounter errors.The Xiaomi G1 robot vacuum cleaner supports only 2.4 GHz networks with 802.11 b/g/n standards. If your router is running in 802.11ac or Wi-Fi 6 mode, temporarily disable these features.

Instructions for connection:

1. In the Xiaomi Home app, click Add Device and select the Xiaomi G1.
2. Make sure the vacuum cleaner is on and near the phone (no more than 1 meter away).
3. The application will offer to connect to the temporary network of the vacuum cleaner (the name will begin with the Xiaomi_Vacuum_). Get her on.
4. Go back to the app and select your 2.4GHz home network from the list. Enter your Wi-Fi password.
5. Wait until the process is complete (it can take up to 2 minutes) and a successful connection will confirm the vacuum cleaner's audible signal and the notification in the application.

If the connection is suspended during the “Connect to the device” step, try the following steps:

• 🔄 Restart router and vacuum cleaner (hold power button for 5 seconds).
• 📵 Turn off your mobile data – sometimes it interferes with the connection.
• 🔐 Make sure that the Wi-Fi password does not contain Cyrillic characters or spaces.

Vacuum charged at 30%+

The router supports 2.4 GHz

Password from Wi-Fi without Cyrillic

VPNs and ad blockers disabled

The phone is connected to the same 2.4 GHz network-->

⚠️ Warning: If after several attempts the vacuum cleaner has not connected, check the region in Mi Account. Accounts with China region can block the connection of devices for other countries. Change region to Russia in the profile settings.

4.Tune the robot vacuum cleaner after connecting

After successful synchronization with Wi-Fi, the vacuum cleaner control panel will open, and you can configure the basic parameters of operation here:

Pay special attention to the mapping of the room.

1. Place the vacuum cleaner on the base and click the Map in the app.
2. Select Create a map and start cleaning in Full mode.
3. After cleaning is complete, save the map and mark out the rooms (bedroom, kitchen, corridor, etc.).

If the vacuum cleaner doesn't build a map or gets lost indoors, check the lighting: in dark rooms, the sensors may not work properly. Also make sure there are no mirrors or glossy surfaces on the floor - they knock down the laser rangefinder.

5. Common errors and their elimination

Even with the correct following of the instructions, there can be failures. Let's consider the typical problems and ways to solve them:

Error: "I was unable to connect to the device"

• 🔌 Check that the vacuum cleaner is on and near the phone.
• 📶 Make sure your phone is connected to a 2.4 GHz network (not 5 GHz!).
• 🔄 Restart router and vacuum cleaner (hold power button for 10 seconds).

Error: "Offline device"

• 🔋 Check the charge of the vacuum cleaner - at a discharge below 15%, it disconnects from the network.
• 📡 Reconnect the vacuum cleaner to Wi-Fi via the app (Device Settings) → Wi-Fi network).
• 🔄 Update the vacuum cleaner firmware in the Settings section → Update of the PO.

Error: "Incorrect Wi-Fi password"

• 🔐 Make sure the password is entered without errors (registration is important!).
• 📵 Turn off Network Hiding in router settings (vacuum cleaner does not see hidden ones) SSID).
• 🔄 Restart your router and try to connect again.

6 Additional functions and integrations

The Xiaomi G1 robot vacuum cleaner supports advanced features that make it even more convenient:

Voice control:

• 🎤 Alice (Yandex): Connect the vacuum cleaner through the Yandex application using the command "Find my devices".
• 🤖 Google Assistant: Add your Mi Home account to Google Home in Smart Home.
• 🍎 Siri (iOS): Requires a HomeKit application and a bridge for integration (e.g. Home Assistant).

Automation:

In the Xiaomi Home application, you can create scenarios, for example:

• 🕒 Start cleaning when leaving home (by geolocation).
• 🌡️ Cleaning with increasing humidity (if connected hygrometer Xiaomi).
• 🔋 Return to base at under 20%.

Firmware update:

Regular updates improve the vacuum cleaner, to check the relevance of the software:

1. Open the Xiaomi Home app and select your vacuum cleaner.
2. Go to Settings. → Update of the PO.
3. If a new version is available, click Update and wait until it is completed (don’t turn off the vacuum cleaner!).

💡

If the vacuum cleaner after the update began to work worse (for example, builds a map worse), roll back the firmware. To do this, in the Xiaomi Home application, go to Settings → About the program and press 10 times on the software version. A hidden menu with a rollback option will appear.

7. Security and confidentiality

Xiaomi smart devices collect data about your home, so it’s important to set up privacy:

What the vacuum cleaner collects:

• 📍 Map of the room: Saved in the cloud Xiaomi (can be turned off in the settings).
• 📊 Cleaning statistics: Working hours, area, errors.
• 🔧 Device Logs: Information about firmware and connections.

To limit data collection:

1. In the Xiaomi Home app, go to Profile → Settings → Privacy.
2. Turn off the options Send Diagnostics and Improve Maps.
3. Delete the saved room maps in the Map Management section.

We also recommend:

• 🔐 Use a complex password for your Mi Account (at least 12 characters).
• 📵 Disable automatic connection of the vacuum cleaner to public Wi-Fi networks.
• 🔄 Regularly update firmware – new versions close vulnerabilities.

💡

For maximum security, disable remote access to the vacuum cleaner in the application settings, which will prevent the device from being controlled over the Internet, but saves the work on the local network.

FAQ: Frequent questions about Xiaomi G1 connectivity