How to set up a robot vacuum cleaner Xiaomi G1 via Mi Home app: full instructions from A to Z

Xiaomi robot vacuum cleaner G1 — One of the most popular cleaning automation assistants, but it only comes with the right setup through the Mi Home app, which many users find difficult to connect to: It doesn't find the network, doesn't build a map, or ignores the cleaning areas. In this article, we'll take a look at Xiaomi's step-by-step setup instructions. G1 — from first turn on to fine calibration of parameters for perfect cleaning.

Feature of the model G1 — Laser navigation support LDS Wet cleaning functions, but without the right settings in the application, these options can work inefficiently. We will show you how to avoid typical mistakes (for example, a mismatch between the region in Mi Home and the vacuum cleaner firmware leads to failures in the construction of the map), adjust the cleaning schedule to your schedule and optimize water consumption when washing floors. And at the end of the article - answers to frequent questions and life hacks from experienced owners.

Preparing for the first run: what to do before setting up in Mi Home

Before you open the Mi Home app, make sure that all the preliminary steps are followed, which will save time and save you from connection problems.

First, charge the robot vacuum cleaner at least 30%. To do this, connect it to the charging base (included) and wait until the indicator on the case lights up in blue (blinking red is discharge, constant blue is charging, permanent green is charging Xiaomi). G1 will not turn on if the charge level is below 20%, and when connecting to the application it is recommended to have at least 50%.

Check your Wi-Fi network:

• 📶 5GHz networks are not supported – only 2.4GHz.
• 🔒 If you have a dual-band router, split up networks (e.g., create a separate network). MyWiFi_2.4G).
• 🌐 Name of the network (SSID) must not contain Cyrillic or special symbols (only Latin, numerals, hyphen/emphasis).
• 🔑 The network password should be no shorter than 8 characters (preferably 12 characters).+).

⚠️ Note: If your router uses the Smart Connect feature (automatic switching between 2.4 and 5 GHz), turn it off in the router settings. G1 It will not be able to connect to such a network.

Also prepare your smartphone:

• 📱 Install the latest version of Mi Home (App Store/Google Play).
• 📲 Turn on Bluetooth and Wi-Fi on your phone.
• 🌍 Make sure that the phone settings are China (this is important for the correct firmware operation).

Installation and configuration of the Mi Home app for Xiaomi G1

Mi Home app – Xiaomi’s central management tool G1. Its installation and initial setting take no more than 5 minutes, but the stability of further work depends on the correctness of this stage.

Download Mi Home from the official store:

• 📱 App Store for iOS (requires iOS 10.0 or later).
• 🤖 Google Play for Android (requires Android 5.0)+).

After installation, open the application and follow the following steps:

1. Sign-in: If you already have a Xiaomi account, log in with your details. If not, sign up (via email, phone number or Google account).
2. Select a region: In the upper right corner, click the flag and select China. G1 Optimized for Chinese server.
3. Adding device: Press + top-right → Add the device → Search for Mi Robot Vacuum G1 (or scan. QR-vacuum-body).

If the app does not find the device, check:

• 🔋 Charge level G1 (must have ≥30%).
• 📡 Distance between vacuum cleaner and router (no more than 5 meters at the connection stage).
• 🔄 Restart your router and smartphone if the connection fails.

💡

If after selecting the region "China" the application interface became in Chinese, go to Profile → Settings → Language and select English or Russian (if available).

Step-by-step: how to connect Xiaomi G1 Wi-Fi via Mi Home

The most important step is to connect the vacuum cleaner to your network. Follow the instructions carefully to avoid errors.

1. Turn on Xiaomi G1, press and hold the power button on the body (3 seconds) and wait for the beep and voice message in Chinese (this is normal).

2.In the Mi Home app, click Add Device → Choose Mi Robot Vacuum G1. It'll appear on screen. QR-code.

3. Hold the smartphone to the vacuum cleaner so that QR-code hits the camera's field of view G1 (It's under the lid, next to the power button. Hold the phone 10 to 15 cm away:

• 💡 Check the lighting (QR-code should be clearly visible).
• 🔄 Restart the vacuum cleaner (hold the power button for 10 seconds).
• 📱 Try using another smartphone (sometimes budget phone cameras can't handle scanning).

4. After a successful scan, the vacuum cleaner will sound and a request for Wi-Fi connection will appear on the phone screen. Select your 2.4 GHz network and enter the password.

• 🔄 Reboot the router.
• 📵 Make sure the router is offline. MAC-filter.
• 🛡️ Temporarily disable the firewall or antivirus on your phone.

QR-code-scanned|2.4 GHz network turned on|Wi-Fi password is correct|Robot vacuum cleaner charged at 30%+|Bluetooth on your phone is on-->

Set up the basic cleaning parameters in Mi Home

After connecting to Wi-Fi, the main management menu of Xiaomi will open G1. Here you can set the basic parameters that will affect the quality of cleaning.

Selection of cleaning mode:

Schedule setting: Go to the Schedule and add new tasks.

• ⏰ Start time of cleaning (for example 10:00 am).
• 📅 Days of the week (you can choose separate days or set a repetition).
• 🏠 Cleaning areas (if the map is already built).
• 💧 Wet cleaning mode (on/off).

⚠️ Warning: If you are installing cleaning during your absence, make sure there are no items in the room that could interfere with your cleaning. G1 (So, for example, hanging wires or toys on the floor, and the robot can hook up and stop cleaning.

3. Water options for wet cleaning: In the menu Cleaning settings → Wet cleaning select water supply level:

• 💧 Low - for laminate or parquet (minimum moisture).
• 💦 Medium - for tiles or linoleum.
• 🌊 High - for severe pollution (for example, after street shoes).

💡

To extend the life of wet cleaning wipes, use low or medium water levels. High mode leads to rapid wear of the fabric and can leave divorces on the floor.

Building a room map and setting up cleaning areas

One of the key advantages of Xiaomi G1 — It allows you to create an accurate map of the room, divided into rooms and zones, and it allows you to flexibly adjust cleaning, eliminating unnecessary areas or paying more attention to contaminated areas.

How to build a map:

1. Start cleaning in Full Cleaning mode (vacuum cleaner will bypass the entire room).
2. Wait until the finish (usually takes 20–40 minutes depending on the area).
3. Once completed, open the map in the Mi Home app (Map section).

If the map is not built correctly (for example, the rooms merged into one or there are no walls):

• 🔄 Restart cleaning from scratch (remove the current map in the settings).
• 🚪 Close all doors so that the vacuum cleaner does not move between rooms during the scan.
• 📏 Make sure there is enough lighting in the room (laser sensor doesn’t work well in the dark).

Division into rooms and zones:

1. In the Map section, click Edit.
2. Use the Add Room tool to circle the contours of the rooms.
3. Name the rooms (e.g., "Kitchen", "Bedroom") for convenience.
4. If necessary, add the No-go zones (such as around the animal feeder) or the Intensive Cleaning Zone (such as at the front door).

Xiaomi’s subtle settings and hidden features G1

In addition to the basic parameters, Mi Home has hidden settings that allow you to optimize the vacuum cleaner for specific conditions.

1. Sensor sensitivity settings: Go to Settings → Additionally. → Sensors and adjust:

• 🚫 Obstacle sensitivity: When high, the robot will stop at furniture more often.
• 🪟 Sensitivity to walls: if the vacuum cleaner "beats" on the boards, reduce the value.
• 🪑 Carpet Detection: Turn on if you want the robot to automatically increase power on carpeting.

Battery Optimization: To extend battery life:

• 🔋 Enable Eco Charging Mode (in battery settings) The robot will charge up to 80%, which reduces wear and tear.
• ⚡ Turn off Fast Charging if vacuum cleaner is rarely used (constant fast charging reduces battery life).

3. Voice notifications: Xiaomi G1 Supports voice prompts in Chinese, but can be disabled or replaced:

• 🔇 Turn off your voice completely in Settings → Sound. → Voice prompts.
• 🎵 Upload custom sounds (e.g. English) through third-party firmware (requires root access).

4.Integration with a smart home: G1 You can connect with other Xiaomi devices:

• 💡 Scenario: If the robot has finished cleaning, turn on the air purifier".
• 🔌 Automation: Start cleaning when everyone leaves the house (via the geofence).

To do this, go to a smart home. → Automation → Add a script.

Updating the firmware and solving typical problems

Regular firmware updates fix bugs and add new features, but an incorrect update can cause crashes.

How to update firmware:

1. Connect. G1 to the charging base and make sure the charge level ≥50%.
2. Open Mi Home, go to Device Settings → Firmware update.
3. If a new version is available, click Update and wait until it is completed (don’t interrupt the process!).

⚠️ Warning: If the vacuum cleaner behaves inadequately after the update (for example, does not build a map or ignores zones), reset the settings (hold the power button for 10 seconds) and set it up again.

Common problems and solutions:

If the problem is not solved, try:

• 🔄 Reboot the vacuum cleaner (hold the power button for 10 seconds).
• 📱 Reinstall the Mi Home app.
• 📧 Contact Xiaomi Support (attach error log from Settings) → Journal).

FAQ: Answers to Frequent Questions about Xiaomi G1