The Xiaomi Robot Vacuum V10 series of robotic vacuum cleaners have proven to be reliable helpers in keeping the house clean, but even the most advanced appliances require regular maintenance. Many owners wonder whether it is possible to wash the machine whole, and often make critical mistakes that lead to breakdowns of electronics. It is important to understand that a full wash under the faucet is strictly forbidden, since inside the case there are batteries and a motherboard.
Proper care of the Xiaomi V10 involves disassembling into separate components, each with its own cleaning procedure. Some parts, such as the dust collector and filters, allow contact with water, while the main unit with engines and sensors needs only dry cleaning. In this article, we will discuss in detail the maintenance process of each node to extend the life of your device.
Regularly removing dust and wool from internal machinery not only improves cleaning quality, but also prevents engine overheating. Ignoring gadget hygiene can lead to loss of suction power and unpleasant smell in the apartment. Let's look at a step-by-step algorithm of actions.
Preparation for cleaning and necessary tools
Before you start water treatments, you need to properly prepare the workplace and the robot vacuum cleaner itself. The best option is to use a sink or a large basin where you can freely manipulate the parts without the risk of dropping them. You need a few simple tools that are sure to be found in every house.
For quality cleaning Xiaomi V10 stock up on a soft brush, microfiber and possibly tweezers to remove hair from hard-to-reach areas.Do not use aggressive household chemicals, as residues can damage plastic elements or filter materials.
Be sure to make sure that the robot is turned off and installed on the dock in the “charging off” position, or simply flipped to exclude accidental start of the motors during maintenance.
⚠️ Warning: Never try to wash the main body of the robot, where the wheels, side brushes and battery compartment are located. Water trapped in the motor wheels or on charging contacts will cause a short circuit.
Prepare a dry, well-ventilated space for drying parts, which could be a balcony or a bathroom floor covered with a towel, and it's important that the drying elements are not exposed to direct sunlight that can warp the thin plastic.
Dismantling and cleaning of the dust collector
The first step in the maintenance process is to remove the dust container. In the Xiaomi Robot Vacuum V10, it is located in the central top of the body. Press the lock and gently pull the container up. Don't put too much effort into the extraction mechanism is ergonomically designed.
Open the dust collector lid and pour the bulk of the garbage into the bucket. To remove fine dust that may have stuck in the corners, use a dry brush. If the container is heavily contaminated with sticky dirt, it can be washed under running water, but only the plastic tank itself without filters.
Wash the inside of the tank thoroughly to remove any dust that may block airflow. After washing, be sure to wipe the tank dry with a soft cloth and leave it to dry at room temperature. Do not use a dryer to speed up the process, as hot air can change the geometry of the plastic.
☑️ Cleaning the dust collector
Pay special attention to the air intake holes. If they are clogged, the efficiency of the cyclone system drops sharply. Use a toothpick or a thin spoke to carefully clean these channels, trying not to damage their edges.
Maintenance of the filtration system
Filtration system in Xiaomi V10 It consists of several levels, including the main HEPA-These are the elements that most often cause suction power to decline if not cleaned in time, and the filters trap the smallest particles of dust, allergens and animal hair.
Take it out carefully. HEPA-It can be made in corrugated paper or reusable synthetic material, depending on the configuration, if you have an old-style paper filter, you can't wash it, you can only shake it out and change it once in a while. 2-3 month.
Xiaomi's reusable filters allow for delicate flushing. Wash the filter under a weak jet of cold water until the draining water is clear. Don't brush the filter material with a brush to avoid damaging the microscopic pores.
| Type of filter | Can I wash? | Replacement frequency | Drying time |
|---|---|---|---|
| HEPA (paper) | No. | 2-3 months | - |
| HEPA (synthetics) | Yeah (cold water) | 6-12 months | 24 hours. |
| Preliminary grid | Yes. | 12 months | 2-4 hours |
⚠️ Attention: Installing a wet filter back into the robot vacuum cleaner will cause moisture to enter the engine and mold to form inside the housing.
After washing, leave the filter to dry horizontally for at least 24 hours. Accelerated drying on the battery or heater is strictly prohibited, since the high temperature destroys the structure of the filter material, and it ceases to trap fine dust.
Cleaning of the main brush and side brooms
The central turbobrush is the heart of the mechanical cleaning of your Xiaomi V10, which is responsible for knocking dust out of carpets and directing debris into the dust collector, and eventually, hair, wool and thread are wound onto the shaft of the brush, creating unnecessary resistance to the engine.
Turn the robot over and remove the protective cover of the brush by snapping the locks. Remove the shaft along with the bearings. Using scissors or a special brush cleaning knife (often included), cut the wound hair along the shaft and remove it.
The brush itself can be washed underwater, but the bearings at the ends of the shaft require special attention. If water gets into the bearings, they must be thoroughly dried and smeared with silicone grease so that they do not rust and start to creak.
How often do you clean the bearings?
Side brushes also need care, they are attached to screws or latches, remove them, remove the wound hair and wipe with a damp cloth, if the brushes are badly worn or have lost elasticity, they are better replaced with new ones, because they are consumables.
Care for sensors and wheels
The navigation of the Xiaomi V10 robot depends on the correct operation of many sensors located around the perimeter of the body. Fall sensors, obstacles and laser rangefinder (LDS) must always be clean. Sensor pollution leads to the robot starting to “lose”, fall down stairs or collide with furniture.
Wipe all the black windows of the sensors with a dry or slightly damp microfiber. Pay special attention to the laser rangefinder window on the top tower - even the slightest speck of dust can distort the map of the room. You can use a cotton swab to clean the lens.
The robot's wheels also require periodic cleaning, dust and wool are stuffed into the tread, which can make it difficult to rotate, use tweezers or a toothpick to remove dirt from the rubber notches, wipe the wheels with a damp cloth, trying not to wet the rotation axis.
💡
Use a melamine sponge to clean the heavily contaminated black plastic surfaces of the sensors – it perfectly removes traces of fat and plaque without scratching the plastic.
Check the charging contacts on the bottom of the case and at the docking station. Oxidation of the contacts can cause the robot to stop charging, wipe them with a dry cloth or cotton swab dipped in alcohol.
Drying and assembly of the device
Once all the washable components have been cleaned, the most important step is drying, and how well you dry the parts will determine the future performance of the Xiaomi Robot Vacuum V10.
Place the washed parts (vacuum, filters, brushes) on a towel in a well-ventilated place. Make sure they don't get dust while they dry. Minimum drying time for filters is 24 hours, for plastics 4-6 hours.
Before you put the robot back together, visually inspect all the elements for residual moisture, especially the internal angles of the dust collector and the filter structure, and assembling a wet device is equivalent to breaking it.
Put the device in reverse sequence: install dry filters, close the dust collector, insert the main brush and close the lid. Set the side brushes and gently place the robot on the floor. Turn on the device and start a short cleaning for inspection.