Xiaomi Mi Home Security Camera 360° 1080p: from unpacking to first shoot

Xiaomi Mi Home Security Camera 360° 1080p

step-by-step

The camera supports the rotation of 360° horizontally 108° vertically, recording in full resolution HD (1920×1080) frequent 20 frame/s, and two-way audio, but to make all these functions work, you need to set the device up properly. If you have already tried to connect the camera and faced problems, click on the section “Prevalent errors and their solutions”, where we have collected proven ways to troubleshoot.

In the article you will find:

• 📦 Preparation for connection (what to check before unpacking)
• 📱 Step-by-step instructions with screenshots from the Mi Home app
• 🔧 Configure key functions (discovery zones, memory card recording, night mode)
• ⚠️ List of errors and their solutions (from "incorrect Wi-Fi password" to "camera does not turn")

1.Preparation for connection: what to do before unpacking

Before you take your camera out of the box, make sure that all the conditions for a successful connection are met. 90% of the problems arise from not meeting basic network or device requirements.

First, check the compatibility of the router. Xiaomi Mi Home Security 360 camera° 1080p It only works with 2.4 GHz networks (5 GHz not supported!) if your router broadcasts both frequencies under the same name (SSID), Separate them in the router settings:

• 📶 Internet speed is not lower than 2 Mbps (for stable broadcasting)
• 🔒 Type of encryption - only WPA2-PSK (AES). WEP or WPA3 won't fit
• 📱 Mi Home version – no lower than 6.0 (update to Google Play or App Store)

Second, get the device ready to set up. A smartphone or tablet on Android 5.0 is fine.+ / iOS 10.0+ Bluetooth 4.0 (required for initial camera anchoring) If you have an older iPhone 6s, You may need to update the firmware.

⚠️ Attention: If you are using VPN or proxy on your smartphone, disable them before setting up. Xiaomi servers may block the connection due to "untrusted" IP-addresses, especially in restricted regions (e.g. some CIS countries).

2 Unpacking and physical connection of the camera

It comes with Xiaomi Mi Home Security 360.° 1080p you will find:

• 📼 The camera itself with a rotating module
• 🔌 Power adapter (5V/2A) micro-USB cable
• 📄 Short instructions in several languages (Russian may not be available)
• 🔧 Strength bracket and screws for installation on the wall / ceiling

Place the camera on a flat surface (such as a desk or shelf) 1-2 meters from the router. Do not plug the power in immediately - first follow the following steps:

Make sure the power adapter meets your country’s standard (220V)|Check the integrity of the Micro-USB cable (no inflections)|Place the camera in the zone of confident reception of Wi-Fi|Disable the charge saving mode on the smartphone (can interrupt the Bluetooth connection)-->

Connect the Micro-USB cable to the camera, then insert the adapter plug into the socket. The indicator on the front should light up in blue (standby). If the LED flashes yellow, this means that the camera has already been tied to another account (see the section "Camera reset to factory settings").

Wait for the beep (short beep) to confirm that you are ready to adjust, and if there is no sound, check if it is turned off in the camera settings (the Mute button on the back).

3. Installation of the Mi Home app and creation of an account

To control the camera, you need the Mi Home app (formerly Mi Jia) download it from official stores:

• 🤖 Google Play for Android
• 🍎 App Store for iOS

If you already have a Xiaomi account (for example, for a smartphone or fitness bracelet), use it to sign in.

1. Open the application and click Register.
2. Specify a valid email or phone number (for Russia, operators MTS, Beeline, MegaFon, Tele2) are supported.
3. Create a password (minimum 8 characters, with capital letters and numbers).
4. Confirm registration by SMS or an email.

⚠️ Note: If you choose China when registering, some camera features (e.g. cloud storage) may not be available. For Russia and CIS, choose Russia or Europe".

After logging in, the app will prompt you to add a new device (+) In the upper right corner, select Cameras, and in the list, find the Mi Home Security Camera 360.° 1080p (may be displayed as MJSXJ02CM — factory index).

4. Step-by-step camera connection to Wi-Fi

Now, we move on to the most important step - linking the camera to your Wi-Fi network. Follow the instructions in the application, but take into account a few nuances:

Step 1. In the Mi Home app, click "Add device" → "Camera" → Select a model. The system will suggest scanning. QR-code from the camera body (located on the bottom or under the removable cover). If the scanner does not work, enter ID handheld devices (12 characters, for example, 7CD81234A5B6).

Step 2. Bring your smartphone to the camera at a distance of 10-20 cm.

• 📱 Bluetooth enabled on the smartphone (needed to transfer network data)
• 🔊 Volume at maximum – the camera will play voice prompts
• 🔋 The camera is connected to the power (the indicator burns blue)

Step 3: Select your Wi-Fi network from the list and enter your password if the password contains Cyrillic or special characters (e.g., a Cyrillic or a special character, #, $), Replace them with Latin letters and numbers, and the app will automatically test the connection and give you a message "Connect successfully" (takes 30-60 seconds).

Step 4: Wait for the firmware update (if available), the camera will reboot, then it will be ready to go, and the app will have a preview with a real-time picture.

💡

If the camera connects to Wi-Fi but the image is not broadcast, try manually specifying static. IP-Address in the router settings. MAC-camera-address IP (e.g. 192.168.1.100) in section DHCP Reservation.

5.Configure key camera functions

After connecting to Wi-Fi, we recommend you to immediately configure the main parameters for comfortable use:

Pay special attention to setting up detection zones, and by default, the camera responds to movement anywhere in the frame, leading to false notifications (such as from shadows or pets) to adjust the zones:

1. Go to Settings. → Detection. → Activity zones.
2. Click Add Zone and circle the areas you want to control (such as a door or safe).
3. Save the changes and test by waving your hand in the designated area.

To record video to a memory card, use a Class 10 microSD (recommended 32 or 64 GB) card with larger volumes, format the card directly in the application (Settings) → Warehouse → Format it, otherwise the camera won't recognize it.

💡

If you plan to use the camera outside (for example, on the porch), install it in a rain-proof place. IP65, Direct jets of water can damage a microphone or speaker.

6. Common mistakes and their solutions

Even if you follow the instructions accurately, users have problems.-5 errors and ways of eliminating them:

• 🔴 "Wrong Wi-Fi password — check the letter register (password is sensitive!) If the password contains spaces, replace them with accents (_).
• 🔴 "The camera doesn't make sounds -- there's a Mute button on the back of the camera. Press it once to unlock the sound.
• 🔴 "Image slows down or disappears – reduce video quality to 720p or reconnect the camera to the router at 2.4 GHz (5 GHz not supported!).
• 🔴 "Camera doesn't turn" - remove the protective film from the rotating module (sometimes it blocks the mechanism). Also check if the "Privacy" mode is turned on (Settings) → Privacy).
• 🔴 "No motion notifications come" - in your smartphone settings, allow Mi Home to send push notifications (Phone Settings → Notifications → Mi Home).

If the camera is connected but does not save video to the card, check:

• The format of the map should be FAT32 (not exFAT or NTFS).
• Free space – if the card is full, the camera automatically deletes old records.
• Record settings - in Settings → Select "Continuous Recording" or "Movement Recording".

If the camera doesn't turn on after reset (the indicator doesn't burn), hold the reset button pressed 15-20 seconds before the beep (long squeak) and this will force the firmware to be updated to the factory version.

7. Additional features: cloud storage and integration

Xiaomi Mi Home Security 360 Camera° 1080p It supports cloud storage for video recording. Free rates include:

• 📅 Storage of the last 7 days of movement records.
• 🔄 Possibility to view the archives in the last 24 hours.
• 📤 Exporting videos to the cloud (up to 3 renders per month).

To activate the cloud:

1. Go to Camera Settings → Cloud storage.
2. Choose the Basic rate (free) or pay a premium (Premium – 30 days of history, Pro – 90 days).
3. Confirm the binding to the Xiaomi account.

The camera can also be integrated with other Xiaomi devices via the Mi Home app, for example:

• 💡 Ccenario: When detecting motion, the camera turns on Xiaomi Smart Lamp.
• 🔔 Automation: If the camera captures a sound (such as a dog barking), sends a notification to the Mi Band.
• 🚪 Security: Working with Xiaomi’s door opening sensor Door/Window Sensor.

To set up the automation:

1. Open Mi Home → "Automation” (Automation).
2. Click "Add" and select a condition (e.g., "Movement detected").
3. Specify the action (for example, "Switch on the lamp").
4. Save the script and test it out.

8.Resetting the camera to factory settings

If you have bought a used camera or experienced critical errors (for example, permanent communication breaks), a complete reset may be required.

1. Turn the camera off the power.
2. Find the Reset button (a small hole next to the Micro-USB connector) on the back.
3. Take a paper clip or toothpick, press and hold the button for 10-15 seconds until you hear a voice message "Reset successful" (in Chinese or English).
4. Connect the camera to power - it will return to factory settings (the indicator flashes yellow).

After resetting, the camera should be re-associated with the account via the Mi Home app (see section 4). If the reset did not help (for example, the camera does not turn on), check:

• 🔌 Power supply – try another adapter with similar characteristics (5V/2A).
• 📶 Wi-Fi signal strength – if the router is far away, use a signal repeater.
• 🔄 Firmware - in Settings → About the device check the relevance of the software version.

💡

If the camera, after reset, gives an error "The device is tied to another account", contact the previous owner and ask him to remove the device from his Mi Home. Alternatively, contact Xiaomi with a purchase check for forced unlocking.

FAQ: Frequent questions about Xiaomi Mi Home Security Camera 360° 1080p