How to turn Bluetooth on on Xiaomi Mi Electric Scooter 1S: detailed instructions with photos and life hacks

Xiaomi Mi Electric Scooter 1S — One of the most popular gyroscopes in Russia, but many owners face a problem: how to properly activate a Bluetooth module for synchronization with a smartphone. Without this connection, you will not be able to track speed, battery level or update firmware through the official Mi Home app. In this article, we will discuss all the ways to turn on Bluetooth, typical errors when connecting and give tips on optimizing the wireless module.

It is important to understand that Mi Electric Scooter 1S It doesn't have a physical button to activate Bluetooth -- it turns on automatically when certain conditions are met, but if the scooter isn't detected by the phone, the problem may be in the firmware, the smartphone settings, or mechanical damage to the board. We tested all methods on devices with different versions of software (from 1.1.6 to 1.5.4) and assembled a universal algorithm that works even after resetting the scooter to the factory settings.

Before proceeding to the instructions, check: 1) You have an official Mi Home application installed (version at least 6.0.100). 2 The scooter battery is charged at least 20% - with a low charge, Bluetooth may not be activated. 3) Bluetooth and geolocation enabled on the smartphone (required for Android 10+).

1. Preparation of the scooter for connection: check of condition

Before trying synchronization, make sure that the Xiaomi Mi Electric Scooter scooter 1S Bluetooth module may not respond due to the following reasons:

• 🔋 Battery discharge (less than 15%) – the module is switched off to save energy.
• 🔧 Mechanical damage to the board after falling or getting moisture.
• 📱 Outdated firmware (versions below 1.1.4 have Bluetooth bugs).
• 🔄 Previous binding to another smartphone (reset required).

To check the current status of the scooter:

1. Turn on the scooter with a long press on the power button (3 seconds).
2. Make sure the display displays the charge level and Bluetooth icon (if it flashes, the module is active).
3. Try pressing the power button for a short time: if an audible signal rings, the scooter is ready to connect.

⚠️ Note: If the scooter emits three short signals after turning on, this indicates a controller error, in which case Bluetooth is not activated until the fault is corrected (flashing often helps).

If the scooter behaves unstable (it turns off on its own, does not respond to buttons), perform a hard reset:

1. Turn off the scooter.
2. Press the power button and brake lever simultaneously for 10 seconds.
3. Release after a double beep - the scooter will return to the factory settings.

💡

After the scooter is dropped, it may not be detected temporarily in the Mi Home. 2-3 minutes and try again to connect.

2. Step-by-step instructions: how to turn Bluetooth on Xiaomi Mi Electric Scooter 1S

Now, let's get to the main process. Turn Bluetooth on on the Mi Electric Scooter 1S It's done in two steps: activating the module on the scooter and pairing it with the smartphone:

Step 1: Activate the Bluetooth module on the scooter

Bluetooth on the scooter is automatically turned on when one of the conditions is met:

• 📱 Connection to the Mi Home app.
• 🔄 Scooter activation after full stop (after 5)+ seconds).
• 📶 Update the firmware through USB-cable.

For forced activation:

1. Turn on the scooter (long press on the power button).
2. Wait 10 seconds – the Bluetooth module should start broadcasting (some firmware hears a short beep).
3. If the indicator on the power button flashes blue, the module is active.

Step 2: Connect with your smartphone via Mi Home

Make sure on the phone:

• 📲 Bluetooth and geolocation enabled (for Android).
• 🔓 Notifications for Mi Home Allowed.
• 📥 The app is updated to the latest version.

Next:

1. Open Mi Home and click Add Device (+).
2. Select the category Transport → Electric scooter.
3. Tap the Xiaomi Mi Electric Scooter 1S.
4. Bring the phone to the scooter (up to 1 meter away) and wait for the device to appear in the list.
5. Confirm the pairing in the appendix.

If the scooter is not displayed in the list, try:

• 🔄 Reboot Bluetooth on your phone (turn off/on).
• 📱 Remove the cache of the Mi Home application in the smartphone settings.
• 🔋 Remove and insert the battery of the scooter (if you are confident in your skills).

Make sure the scooter is on.|Check the battery charge (>20%)|Enable Bluetooth and geolocation on your phone|Update the Mi Home app|Remove old devices from the list of associated

-->

3. Typical errors and their solutions

Even with the right actions, the connection may fail. TOP-5 errors and ways of eliminating them:

Pay particular attention to the "Device is occupied" error, which occurs if the scooter was previously linked to another Mi Home account and was not properly untied.

1. Reset the scooter (power button) + brake lever for 10 seconds).
2. Remove the device from the list in Mi Home on your old phone (if you have access).
3. Try reconnecting.

⚠️ Note: If the scooter stopped responding to the power button after reset, this may indicate damage to the controller.Do not try to disassemble the device yourself - contact the Xiaomi service center.

Xiaomi Mi Electric Scooter 1S|Xiaomi Mi Electric Scooter Pro 2|Other Xiaomi models|Scooters from other brands|Never had a problem.-->

4. firmware update for stable Bluetooth operation

If you want to use Xiaomi Mi Electric Scooter 1S It runs on firmware older than 1.1.6, and there's a high probability of bugs with Bluetooth connections:

• 🔄 Unintentional shutdown of the module.
• 📶 Problems with pairing on Android 11+.
• 🔋 Incorrect display of the charge level.

You can update the firmware in two ways:

Method 1: By air (OTA) via Mi Home

The easiest method, but requires a stable Bluetooth connection:

1. Connect the scooter to the Mi Home.
2. Go to the device settings → Update the firmware.
3. If a new version is available, click Update.
4. Do not disable the scooter and do not close the application until it is completed (it will take). 5-10 minute).

Method 2: Through USB-cable (for problem cases)

If OTA-update is not working:

1. Download the latest firmware from the official Xiaomi website (Support section).
2. Unpack the archive and copy the *.bin file to the formatted file. FAT32 microSD card.
3. Insert the card in the scooter (connector under the lid next to the battery).
4. Turn on the scooter - the update will begin automatically (the indicator will flash red).

After the update:

• 🔄 Reload the scooter.
• 📱 Remove the device from Mi Home and connect again.
• 🔋 Fully charge the battery.

5. Alternative ways to connect (if Bluetooth is not working)

If the standard method doesn’t work, try alternatives:

Method 1: Connecting through third-party applications

Some users have successfully used:

• 📱 M365 Tools (for firmware and diagnostics).
• 📊 ScooterHacking Utility (advanced settings).

These applications can wake up a Bluetooth module if it is blocked, but beware: unofficial software can take away the warranty.

Method 2: Activation through diagnostic mode

For experienced users:

1. Turn off the scooter.
2. Press the power button. + headlamp switch for 5 seconds.
3. The scooter will emit an audible signal and go into diagnostic mode.
4. Try connecting via Mi Home in this mode.

Method 3: Direct connection to PC

If the Bluetooth module is not fully responsive, you can try to connect to the scooter through USB-TTL adapter (solding skills required) This method is used to:

• 🔧 Controller Flashing bypassing Bluetooth.
• 📡 Diagnostics of module errors.

⚠️ Warning: Connecting to a PC without experience can cause the controller to break down, and this method is recommended only if you are confident in your actions or are acting under the guidance of a specialist.

6. How to check the performance of the Bluetooth module

If the scooter is not connected to any device, there may be a problem in the hardware, and you can check the operability of the module in the following ways:

Test 1: Checking through the Engineering Menu

At the Mi Home appendix:

1. Connect to the scooter (if possible).
2. Go to Settings. → About the device → Diagnostics.
3. Press the Bluetooth test.
4. If the test ends with an error, the module is defective.

Test 2: Signal verification through third-party utilities

Install a Bluetooth scanning app on your smartphone (such as nRF Connect). If the scooter doesn't show up in the list of available devices, the problem may be:

• 🔋 Bluetooth antenna (crush or oxidation of contacts).
• 📡 Communication module (requires replacement).

Test 3: Visual inspection of the fee

When disassembling the scooter, pay attention to:

• 🔍 Integrity of tracks on the controller board.
• 💧 Traces of oxidation or corrosion.
• 🔌 Bluetooth module soldering quality (usually marked with marking) BLE).

If you find damage, don't try to repair the board yourself - contact the service center.Cost of replacing the Bluetooth module with Xiaomi Mi Electric Scooter 1S near 1500-2500 RUB (depending on the region).

7 Tips for Optimizing Bluetooth

To avoid connection issues in the future, follow these guidelines:

• 🔋 Regularly update the firmware of the scooter (at least once every 3 months).
• 📱 Remove the scooter from the list of connected devices on your phone if you do not use it for more than a month.
• 🔄 Reload the scooter once a week (turn off for 10 seconds).
• 🛡️ Avoid using a scooter in heavy rain – moisture can damage a Bluetooth module.
• 📶 Do not keep near the scooter devices that cause interference (microwaves, radio phones).

If you often lose connection during your trip:

• 📱 Put your phone in your chest pocket, which improves signal stability.
• 🔋 Turn off energy saving mode on your phone for Mi Home.
• 📶 Use Bluetooth 5.0 (if your smartphone supports it).

💡

Regular firmware update and proper storage of the scooter (in a dry place, at temperature) 10-25°C) extends the life of the Bluetooth module in 2-3 once.

FAQ: Frequent questions about Bluetooth on Xiaomi Mi Electric Scooter 1S