How to distribute the Internet from Xiaomi Redmi phone to a laptop via Tele2: the complete guide

Reaching the Internet from Xiaomi Redmi to a laptop via Tele2 is a challenge that millions of users face, and it would seem that it could be easier to turn on the hotspot on your phone, plug in your laptop, and it's done. But in practice, even experienced smartphone owners have problems: From no signal to sudden connection breaks, in this article we will examine not only the basic settings, but also the hidden nuances that Tele2 does not advertise, as well as the specific features of firmware. MIUI on Redmi devices.

Tele2 network features dynamic frequency distribution and tariff restrictions that can block the distribution of the Internet. For example, on some tariffs without the option of "Mobile Internet", the speed of the distribution will be artificially reduced to 64 Kbps - this is enough only to check the mail, we will tell you how to check your tariff for such restrictions and circumvent them by legal means. You will also find out why Redmi Note 10 Pro and Redmi 9A Behaving Differently When Giving Wi-Fi, and How to Fix It.

Preparation of Xiaomi Redmi phone for the distribution of the Internet

Before you turn on the hotspot, you have to take a few critical steps, and if you skip them, you run the risk of errors like "Can't turn on the hotspot" or "Connect without Internet access." Start by checking the mobile Internet:

• 📶 Make sure there is a stable signal on the phone.2 (less 2-3 In a low-coated area (e.g. in a basement or on the outskirts of a city), distribution will be interrupted.
• 💳 Check balance and active tariff plan. on some rates Tele2 (For example, "My conversation") the Internet is distributed only after connecting the option "Mobile Internet" for the Internet. 50-150 ₽/month.
• 🔄 Reboot the phone. This will reset the module's temporary malfunctions. Wi-Fi/Bluetooth, which can block the distribution.
• 🛠️ Update the firmware MIUI Up to the latest version. In older versions (below) MIUI 12.5) There are bugs with the access point on some Redmi models.

Pay special attention to the settings APN (Network access points) Incorrect parameters APN — One of the main reasons why the Internet is not handed out even when everything on the phone is working:

To check the current settings APN, Go to Settings. → SIM-maps and mobile networks → Access point (APN). If the settings are different from the table above, create a new profile with the correct data and save it.On some Redmi models (e.g. Redmi 8) after the change APN Reboot the phone, otherwise the changes will not apply.

Enable Wi-Fi hotspot on Xiaomi Redmi

Now we move on to the main stage, which is to turn on the modem modem. MIUI You can do this in two ways: through the notification bar or the settings menu. Let's look at both, because different versions of the firmware may have different interfaces.

Method 1: Through the notification panel (fast access)

1. Swipe your finger down to open the notification panel.
2. Find the Access Point icon (usually hidden under the “More” or “Edit” button).
3. Hold the badge. 1-2 seconds to get into the settings.
4. Activate the Wi-Fi Access Point slider.

Method 2: Through the settings menu (full control)

1. Open Settings → Connections and Sharing → Access Point and modem.
2. Select “Wi-Fi Access Point”.
3. Click on “Access Point Settings” to set the network name (SSID) password.
4. Go back and activate the slider.

By default, Xiaomi generates the network name in the format Redmi_XXXX (where XXXX — last-minute IMEI). We recommend changing it to a more memorable one, for example, Redmi_Hotspot. It is also better to change the password: by default it often consists of 8 Use a combination of letters and numbers at least as long as 10 symbolism.

Connecting a laptop to a Xiaomi access point

When the hotspot is activated on the phone, you have to plug in the laptop, and there's a nuance here, especially if you're using Windows. 10/11 Or macOS. Let's look at both.

For Windows:

1. Click on the Wi-Fi icon in the lower right corner of the taskbar.
2. In the list of available networks, find the name of your access point (for example, Redmi_Hotspot).
3. Enter the password and click "Connect".
4. If the connection does not occur, right-click on the network and select “Forget”, then try again.

For macOS:

1. Click on the Wi-Fi icon in the top panel.
2. Select your network and enter your password.
3. If there is an error, it is not possible to obtain IP-address, go to System settings → Network → Wi-Fi → Additionally, remove the network from the list of known.

Some laptops (especially those with legacy network cards) may have a problem when the device “sees” the network but doesn’t connect.

• 🔧 Update the Wi-Fi adapter driver through Device Manager.
• 🔄 Restart your laptop and phone.
• 📡 Try changing the Wi-Fi channel in the access point settings (e.g. from Auto to Channel 6).

💡

If your laptop is connected but the internet is not working, try turning it off. VPN Some apps (e.g. 1.1.1.1 or Psiphon) block the distribution of traffic.

Solving common problems in the distribution of the Internet

Even if you did everything right, you could have a failure. TOP-5 Errors and ways to eliminate them, typical for Xiaomi Redmi and Tele2.

1. Access point is switched on and off immediately

Reason: conflict with charge savings or background applications.

• 🔋 Open the Settings. → Battery and productivity → Saving charge and disabling it.
• 🚫 Go to Settings. → Annexes → App management, find “Access Point” and disallow optimization.

2.The laptop is connected, but the Internet is not working

Reason: Controller blocking or failures in APN.

• 📞 Check the balance and rate (possibly need a package "Mobile Internet»).
• 🔄 Recreate the profile APN, as described in the first section.
• 🌐 Try to connect to the Internet from your phone – if there is also no connection, the operator has a problem.

Slow speed (less than 1 Mbps)

Reason: operator restriction or network overload.

• 📊 Run a speed test on your phone (e.g., through Speedtest). If the speed is low and there, contact Tele2 support.
• 📶 Switch the network on your phone with 4G on 3G (Sometimes it paradoxically speeds up the distribution).
• 🔄 Change the Wi-Fi range in the access point settings from 2.4 GHz to 5 GHz (if the laptop supports support).

4. The laptop doesn't see the access point

Reason: Incompatibility of Wi-Fi standards or malfunctions in the phone module.

• 🔄 Reboot both devices.
• 📡 Change the Wi-Fi channel in the access point settings (for example, from Auto to Channel 11).
• 🛠️ Update the firmware MIUI — In older versions there are bugs with network visibility.

5. Permanent breaks of connection

Reason: overheating of the phone or interference from other devices.

• 🔥 Remove the case from the phone – it can block the heat sink.
• 📵 Disconnect other devices from the access point (such as tablets or second laptops).
• 🔋 Connect your phone to charge – with a low battery level (15%) MIUI shut off the distribution automatically.

Optimizing Internet Distribution: How to Speed Up Connection

If the Internet is spreading out but it's slow, you can try a few ways to speed up, and it's important to understand that the maximum speed will be limited by your Tele2 fare and coverage conditions, but even within those limits, you can make the most of it.

1. Change the Wi-Fi standard

By default, Xiaomi Redmi distributes the network in the standard 802.11n (Wi-Fi 4 if your laptop supports 802.11ac (Wi-Fi 5, switch to it:

1. Go to Settings. → Access Point and modem → Setting up the access point.
2. Select "Frequency Range" - 5 GHz.
3. Install the "Wi-Fi standard» — 802.11ac.

2. Disable background applications

Many programs (e.g., TikTok, VKontakte, YouTube) consume traffic in the background even when you're not using them, which slows down the speed of the distribution, to prevent them from accessing mobile data:

1. Go to Settings → Applications → Application Management.
2. Select the application and turn off “Mobile Data” and “Background Data Transfer”.

3.Use. USB-cable

If the laptop and phone support USB tethering, this will give you a more stable connection.

1. Connect your phone to your laptop through USB-cable.
2. In the phone settings, select Settings → Connections and sharing → Access Point and modem → USB-modem.
3. On the laptop, wait for the driver installation (usually they are installed automatically).

4. Set up QoS (Quality of Service)

In the firmware MIUI 12.5+ There's a hidden traffic prioritization function to activate it:

1. Turn on Developer Mode (7 times click on Version) MIUI» In Settings → The phone).
2. Go to Settings → Additional → Developer settings.
3. Find “Background Limitation” and turn it off for critical applications (like a browser).

💡

The most stable way to distribute is through USB-It heats the phone less, it's non-interference-dependent, and it's faster than Wi-Fi.

Internet security: how to protect data

Distributing Wi-Fi from your phone is not only convenient, it's also potentially dangerous. If you're in a public place (cafe, airport, park), intruders can try to connect to your network and intercept traffic. Here's how to avoid this:

1.Use a complex password

Don't leave your default password (e.g. 12345678).

• 🔤 10-12 symbolism;
• 🔢 Number, upper and lowercase letters;
• 🔑 Symbols (!@#$% etc.).

2. Limit the number of connected devices

In the settings of the access point (Settings) → Access Point and modem → Setting up the access point, set the maximum number of devices to 1 (if you only connect a laptop), which will prevent the connection of foreign gadgets.

3. Enable hidden mode SSID

If you don’t want your network to appear on the list of available ones, hide it:

1. Go to the access point settings.
2. Activate the “Hide the Network” option.
3. You can only connect to it manually, knowing the name (SSID).

4. Turn off the distribution when you are not using

This will not only save battery life, but also reduce the risk of unauthorized access. MIUI You can set up automatic shutdown of the access point after a certain time:

1. Go to Settings. → Access Point and modem.
2. Select "Time Out" and install 5-10 minute.

💡

If you often give out the Internet in public places, install on a laptop VPN (So, for example, ProtonVPN or Windscribe, and that's going to encrypt your traffic and protect you from interception.

Alternative ways to distribute the Internet with Xiaomi Redmi

If Wi-Fi doesn't work for some reason, you can use other methods of distribution. Let's take two of the most reliable ones.

1. Distribution via Bluetooth

It's slower than Wi-Fi, but it uses less battery and is more stable in the face of interference.

1. Activate Bluetooth on your phone and laptop.
2. Connect devices (on the phone: Settings → Bluetooth, on the laptop – through the notification panel).
3. On your phone, go to Settings. → Connections and sharing → Access Point and modem and turn on the “Bluetooth modem».
4. On the laptop in the list of Bluetooth devices, select your phone and click “Connect via the access point”.

2. Distribution through USB (USB-tethering)

As I mentioned earlier, this is the most stable way, and it works even where Wi-Fi is not catching. USB-cable (preferably original or certified) if the laptop does not recognize the connection:

• 🔌 Try another cable or port. USB.
• 🖥️ Update the drivers USB-modem on a laptop (download them from the manufacturer's website).
• 🔄 Reboot both devices.

3. Distribution through third-party applications

If standard means MIUI They are not available, but alternative programs can be used, for example:

• 📱 PdaNet+ — It allows you to distribute the Internet even at tariffs with a lock.
• 🌐 FoxFi – Supports hidden distribution without operator notification.
• 🔗 ClockworkMod Tether – for advanced users (requires root rights).

However, be careful: some applications may violate the operator’s rules, which can lead to blocking. SIM-Before using, check reviews and rankings on Google Play.

FAQ: Frequent questions about giving away the Internet with Xiaomi Redmi