How to safely exit Fastboot mode on Xiaomi: all ways 2026

Fastboot mode on Xiaomi smartphones is a special engineering mode that is used to firmware the device, unlock the bootloader or restore the system. However, many users face a situation where the phone “hangs” in this mode after a failed update, resetting or experimenting with custom firmware. If your Redmi, POCO or Mi screen is marked with the FASTBOOT with the image of a rabbit in the hat, do not panic – there is a way out.

In this article, we will discuss all the current ways to exit Fastboot on Xiaomi devices, including software methods (via ADB and Mi Flash Tool), hardware button combinations, and nuances for different models. Particular attention will be paid to devices with a locked bootloader, where standard methods may not work. All instructions are tested on MIUI 14/15 firmware and are relevant for 2026.

Why Xiaomi is loading into Fastboot and how to prevent it

Fastboot mode is activated on Xiaomi for several reasons, and by understanding them, you can avoid repeated hang-ups.

• 🔄 Interrupted software update – if the firmware process was interrupted (power is turned off, the battery is down), the system can automatically go to Fastboot for recovery.
• 🔧 Unsuccessful unlocking of the bootloader - when using the Mi Unlock Tool utility, the device reboots in Fastboot, but sometimes gets stuck in it.
• 📱 Failure after resetting – if you performed hard reset via Recovery, but the system failed to boot properly.
• 🔌 Battery or power problems – at a critically low charge (less than 5%), the device can get “hungry” on the Fastboot screen.

To minimize the risk of getting into this mode, always keep an eye on the battery charge (at least 30% before manipulating the system) and use the original USB Type-C cable. If you often experiment with firmware, we recommend keeping the Mi Flash Tool and backup data on hand.

⚠️ Note: On Xiaomi devices with Qualcomm Snapdragon processors (e.g. Redmi Note 12 Pro)+, POCO F5) Output from Fastboot can be blocked due to active protection of Anti-Rollback.In this case, you will need an official firmware with a version not lower than the current one.

Method 1: Exit via button combination (for most models)

The simplest method is to use hardware buttons, which works on 90% of Xiaomi devices, as long as the system is not critically damaged.

1. Hold the power button for 10-15 seconds until the screen goes out.
2. As soon as the device is turned off, immediately press the combination: 🔘 Power button + Volume up (to move to Recovery). 🔘 If it doesn’t work, try the power button. + Loudness down (direct access to the system).

Mi

5-8 seconds

If the device boots into Recovery, select Reboot → Reboot to System. If the screen shows Fastboot again, move on to the next method.

Check if the power button is stuck (mov it)

Connect the charger for 10 minutes (possibly the battery is dead)

Try another combination: Volume up + Volume down + Nutrition (for older models)

-->

Method 2: Use ADB and Fastboot Tools (for PC)

If the hardware method doesn't work, connect the device to your computer and use ADB and Fastboot utilities, which require drivers installed and minimal command line knowledge.

First, download and install:

• 🖥️ Google Platform Tools (includes adb and fastboot).
• 🔌 Xiaomi Drivers (if Windows does not recognize the device in Fastboot).

Next, run on the command line (CMD or Terminal):

fastboot devices

If the device is determined (its serial number will appear), enter:

fastboot reboot

If the team doesn’t work, try:

fastboot oem reboot-recovery

This will reboot the device in Recovery, from where you can try booting into the system.

⚠️ Note: Some models (e.g. Xiaomi) 13T, Redmi K60) The fastboot oem unlock command can reset all data.

Method 3: Firmware via Mi Flash Tool (for locked devices)

If previous methods didn't work, it's likely that the system is damaged or the bootloader is blocked, and the official firmware through the Mi Flash Tool will help, which will reset all the data, but bring the device back to life.

Steps:

1. Download the official firmware for your model (choose the Fastboot version).
2. Unpack the archive in a folder without Cyrillic characters (for example, C:\MiFlash\rom).
3. Install the Mi Flash Tool and run it on behalf of the administrator.
4. Connect your phone in Fastboot mode and press Refresh – the device must be determined.
5. Select a firmware folder and click Flash. At the bottom, choose clean all (complete clean) or save user data (save data, but doesn't always work).

It takes 5-10 minutes, and when it's done, it automatically restarts.

1. Reinstall drivers manually through Device Manager.

2. Use another USB-port USB 2.0).

3. Run the utility in compatibility mode with Windows 8.

-->

Method 4: Test Point (for devices with a locked boot loader)

If the bootloader is locked and the Mi Flash Tool needs to be unlocked, you can use the Test Point method. This is a hardware method that bypasses the protection and allows you to flash the device.

Instructions:

1. Turn off the device (hold the power button for 20 seconds).
2. Remove the back cover (for models with removable body) or gently slap the volume key (on monolithic devices Redmi Note 10 Pro, POCO X3 Pro Test Point is under the button).
3. Close the Test Point contacts (usually two metal dots labeled TP) with tweezers or a needle.
4. Connect. USB-cable to PC – the device is defined as Qualcomm HS-USB QDLoader 9008.
5. Sweat the device through the Mi Flash Tool (select EDL firmware).

Once you have the firmware, assemble the device and perform the initial setup, which works even on bricks (devices that don't turn on at all).

⚠️ Warning: Test Point failure can damage the motherboard. If you're unsure of your skills, contact the service center. On devices with MediaTek processors (e.g., Redmi). 10A) This method does not work – it is required SP Flash Tool.

Button combination

ADB/Fastboot Teams

Mi Flash Tool

Test Point

Another way.-->

Method 5: Recovery via EDL Mode (for advanced users)

EDL Mode (Emergency Download Mode) is a firmware emergency mode used to recover devices with serious software damage, and is available on most Xiaomi devices with Qualcomm processors.

For EDL entry:

1. Turn off the device.
2. Hold and hold Volume up + Volume down.
3. Connect. USB-cable to PC – the device must be defined as Qualcomm HS-USB QDLoader 9008.

Next, run the device through the Mi Flash Tool (select firmware marked EDL) or QFil. This method is guaranteed to restore performance, but requires strict adherence to the instructions.

For MediaTek devices (e.g. Redmi 9A, POCO C40), use the SP Flash Tool and scatter firmware.

💡

EDL Mode is the last chance to bring the brick back to life, but once the firmware is running through the EDL, it may be necessary to re-unlock the bootloader (if it has been unlocked before).

Frequent mistakes and their solutions

When trying to log out of Fastboot, users often encounter errors, and here are the most common ways to fix them:

If none of the methods worked, there may be a problem with the hardware (damaged memory, power controller), in which case we recommend contacting the Xiaomi service center.

FAQ: Answers to Frequent Questions