How to turn on Xiaomi device after resetting: from smartphone to smart technology

Why Xiaomi doesn’t turn on after a reset and what to do about it

Have you reset your Xiaomi device (whether it’s a smartphone, TV or smart speaker) but it stubbornly doesn’t respond to the power button? This situation is familiar to many users – after a hard reset or software reset via Settings. → The phone. → Resetting techniques can "hang" on the logo, cyclically reboot or not give any signs of life. MIUI, hardware conflicts or incorrect completion of the resetting process.

In 80% of cases, the problem is solved without going to the service center – just follow an on-line algorithm that takes into account the device model and type of reset. For example, Redmi Note smartphones often require a forced reboot through a combination of buttons, while Mi TVs can get stuck during the Wi-Fi setup stage. In this article, we will analyze all possible scenarios from basic actions to recovery via Fastboot or Recovery, and also warn against typical errors that can turn a temporary malfunction into a brick.

Before you start the instructions, answer the key question: What type of reset did you perform?

🔄 Mild reset (via the settings menu) – usually not causing problems, but can “hang” during the reboot stage.
🛠️ Hard reset (via Recovery or button combination) – more often leads to cyclical loading.
📱 Mi Account Reset (remote) – a risky method if the device is not synchronized.

📊 What Xiaomi device is you trying to turn on?

Smartphone (Redmi/POCO/Mi)

Television (Mi TV)

Smart speaker/lamp

Fitness bracelet

router

Other

First steps: check the baseline parameters before inclusion

If Xiaomi doesn't respond to the power button after a reset, don't rush to disassemble the case or look for firmware.Start by diagnosing hardware conditions that are often overlooked:

⚠️ Warning: Connecting to charge a faulty cable or power supply can mimic the device's "dead" state. Always use the original Quick Charge-enabled adapter (for smartphones) or the regular cable from the kit.

🔋 Battery Charging: After resetting, the battery could discharge to 0%. Connect the device to the network at a minimum 30 minutes, even if the lights don't go on. POCO F3/F4 redmi K40 Characteristics of the charging delay to 10-15 minute.
🔌 Check cable and socket: Use a different cable and socket (or USB-On the Mi TVs, on the PC port. TV Q1/Q2 faulty cable HDMI can block the switching on.
🌡️ Temperature of the device: If the case is hot, let it cool down 20-30 Overheating after reset can cause hardware locking (especially on devices with Snapdragon processors). 8xx).
🔄 Forced reboot: Press the power button on 20-30 Seconds (for smartphones) or Power + Loudness up on 10 On the Mi TVs. TV Hold the power button on the remote. 15 seconds.

If you don't turn on after this manipulation, move on to the next section. Exception: if you changed your firmware or unlocked your bootloader before reset, go straight to Fastboot Recovery, which is critical!

Check the charging with the original cable|Wait. 30 minute|Try another socket./USB-port|Make sure the device is not overheated.|Perform a forced reset-->

Xiaomi smartphones: step-by-step inclusion after hard reset

Xiaomi smartphones (Redmi, POCO, Mi series) can behave differently after reset depending on the model and version of MIUI. Below is a universal algorithm that works for 95% of devices released after 2018.

1. Standard inclusion (if the reset was successful)

📱 Press and hold the power button. 5-7 A few seconds before the logo appears. MI.
🔄 If the device has been stuck on the logo for longer than 5 minutes, perform a forced reboot: + Volume up for 10 seconds.
🌐 Once downloaded, select a language, connect to Wi-Fi, and follow the instructions of the setup wizard. At the stage of signing in to Mi Account, you can skip the binding (if there was no lock). FRP).

2. if the smartphone is cyclically rebooted

Cyclical reboot is a typical problem after a hard reset via Recovery.

🔧 Damaged firmware files (often on devices with unlocked bootloader).
📦 Conflict with previously established TWRP ornamental.
🔒 Lockdown FRP (Factory Reset Protection, if the reset is made without a Mi Account detachment.

Decisions:

Boot in Recovery: Turn off the phone, then press Power + Volume up until the menu appears.
Select Wipe Data → Wipe All Data (even if you have already reset!).
If the bootloop continues, go to the Fastboot Recovery section.

What to do if your smartphone requires a password after resetting?

If after reset, Xiaomi asks for a password from Mi Account, whom you don’t remember, it’s a good idea. FRP-The lockdown: 1. Enter the tethered email/Phone and password (if you remember). 2. If your data is lost, use the Mi Account recovery service. 3. To get around FRP on older models (up to) 2020 Mi Flash Unlock can be used, but this requires unlocking the bootloader. ⚠️ On new devices (e.g. Redmi Note) 12) circumvention FRP without account data is impossible - you will need to contact the service center with proof of purchase.

Mi TVs: Enable after reset to factory settings

Mi TVs (Q1, P1, A Pro) often get stuck in the setup phase or do not respond to the remote after reset, and unlike smartphones, power supply and connectivity cables play a key role.

Basic actions

🔌 Turn off the TV from the socket for 1 minute, then turn it back on.This will reset PatchWall's cache.
🎮 Remove the batteries from the remote for 30 seconds (even if the indicator is on).
🔄 Press and hold the power button on the TV body (not on the remote!) for 15 seconds - this will force the system to restart.

2. if the TV is turned on but does not pass the setting

After resetting, the Mi TV can:

📶 Hang in the Wi-Fi connection phase – try using a mobile hotspot instead of a home router.
🔒 Require password from Mi Account – enter details or skip step (if the account was not tied).
🖥️ Not seeing the signal sources (HDMI) — discharge HDMI-Ports in the menu settings → Devices and accessories → Reset HDMI.

If the TV is cyclically rebooted, try turning off all external devices (configures, sound bars) and re-setting. On Mi TV Q1E and later, a USB rollback can help:

Download the firmware for your model from the official website.
Unpack. ZIP-archive and copy the file update.zip flash-drive (FAT32).
Connect the flash drive to the TV, pinch Menu + Power on the remote until the update menu appears.

💡

If the Mi TV doesn’t respond to the remote after reset, try connecting the keyboard or mouse over USB – they often work even when Bluetooth connections fail.

Smart devices Xiaomi: speakers, lamps, bracelets

Xiaomi smart devices (e.g., Mi Smart Speaker speakers, Yeelight bulbs, Mi Band bracelets) require re-association with the Mi Home app after reset, but sometimes they are not turned on or detected on the network.

1. Smart speakers and lamps

🔊 Column not turned on: Hold the power button 10 If you don't have a reaction, check the power supply (should be) 5V/2A).
💡 The lamp flashes but doesn't connect: Reset after 5 times power on/off (2 seconds interval). After that, the lamp should flash yellow, so it's ready for a new binding.

2.Mi Band fitness bracelets

Mi Band 5/6/7 bracelets after reset (via Settings → Reset in the application) can:

📱 Do not sync with your phone – remove the device in Mi Fitness and add again.
🔋 Discharge quickly – Calibrate the battery: discharge the bracelet to 0%, then charge to 100% without interruption.
🔒 Demand PIN-code – default is 0000 or the last 4 digits of the tied phone.

For Mi Band 8 and later bracelets after reset, you may need to update the firmware through the app. If the bracelet does not turn on at all, place it on charge for 2 hours - sometimes a discharged battery blocks the start.

Recovery with Fastboot and Mi Flash Tool

If a Xiaomi device does not load beyond the logo after a reset or reboots cyclically and standard methods do not help, recovery through Fastboot will be required.This method is suitable for smartphones and some tablets, but requires a PC and special tools.

⚠️ Note: Mi Flash Tool misuse can turn a device into a brick.This method is recommended only for users with firmware experience or if other methods are exhausted!

Step-by-step instruction

Install drivers: Download Mi Flash Tool and Qualcomm drivers (for Snapdragon) or MediaTek (for Helio/Dimensity processors). Connect the smartphone turned off to your PC, keeping Volume down + Power (Fastboot mode).

Download the firmware:

Select the MIUI version for your model on Xiaomi Firmware Updater.
Download the file with the.tgz extension and unpack it into a folder without Cyrillic characters.
Sweat the device: 1. Open the Mi Flash Tool on behalf of the administrator. 2. Press "Select" and specify the path to the unpacked firmware. 3. Connect the phone in Fastboot mode. 4. Select "Clean all" or "Clean all and lock" (Reset + lock the bootloader). 5. Press "Flash" and wait for completion (10-15 minutes).

After successful firmware, the device will restart and prompt the initial setup if the process is completed with an error (e.g, anti_rollback), So you're trying to install an older version. MIUI, It's more than the one before the dump:

Download a newer firmware.
Or use the XiaomiTool V2 tool to automatically select the version.

💡

Use the "Clean all and lock" mode in the Mi Flash Tool only if you plan to sell the device, otherwise the bootloader will remain unlocked, which will simplify future firmware.

Common Mistakes and How to Avoid Them

Many users compound the problem of turning Xiaomi on after a reset by making standard errors, and here is a list of the most common mistakes and their consequences:

Mistake.	Effects of consequences	How to avoid
Recovery reset on a discharged battery (<20%)	The device shuts down during the process, and system files are damaged.	Charge your smartphone up to 50% before resetting
Use of informal firmware after reset	Cyclical download, blocking Mi Account	Install only official versions of MIUI from Xiaomi website
Interrupting the reset process (removing the battery, disconnecting the power)	Brick – the device does not even include in the Fastboot	Wait for the full reset to be completed (may take up to 10 minutes)
Resetting Mi Account without decoupling on FRP devices	Blocking of the account, requiring the entry of data of the previous owner	Untie your account in Settings → Accounts → Mi Account → Delete your account before resetting
Using custom TWRP to reset on new devices	Damage to the anti-rollback partition, impossibility of firmware	On devices 2021+ year, use only stock Recovery

Pay special attention to devices with unlocked bootloader. After reset, they may require re-unlocking through the Mi Unlock Tool, as well as losing the warranty. If you are not sure about your actions, you should contact the Xiaomi service center - especially if you are talking about flagship models (Xiaomi 13/14, Redmi K60).

FAQ: Frequent questions about Xiaomi's inclusion after reset

My Xiaomi Redmi Note 10 Pro shows "This device is locked" after reset and doesn't turn on. What do I do?

This message means that the device has activated a lock. FRP (Factory Reset Protection), and you have performed a reset without detachment Mi Account. Solutions: Enter the email and password from the associated account (if you remember). If the data is lost, restore access via account.xiaomi.com. FRP You can use the Mi Account Bypass Tool on the Redmi Note 10 Pro, but this requires unlocking the bootloader and risks locking the device permanently. ⚠️ On New Devices (2022)+ round-about FRP without account data is impossible - you will need a purchase check to unlock the service.

Mi TV Q2 can't find Wi-Fi after reset. What's the problem?

When reset, Mi TVs often reset the Wi-Fi settings. Try: Connect via an Ethernet cable (if there is a port); use a mobile hotspot with your phone (sometimes the TV "sees" direct networks better); Reset network settings: Settings → Networks and the Internet → Reset network settings. Update firmware via USB (instructions in the section about TVs). If the problem persists, check if the Wi-Fi module in the service menu is disabled (available via remote: Menu → 4 times up OK → 2 times down → OK → →

After the Xiaomi Mi 11 is reset, the screen doesn't turn on, but the phone vibrates and makes sounds. What do you do?

This is a typical symptom of damage to a graphics driver or a firmware conflict.Try: Connect your phone to a PC and check if it's defined as a media device (if so, a problem in the screen). + Power, and run the device through the Mi Flash Tool (instruction above).If the screen is still not working, check the display plume (it may have left after reset). AMOLED-The solution is firmware via Fastboot with the option of Save user data (if available).

Can I turn on Xiaomi after reset without a power button?

Yes, but the method depends on the model: Smartphones: Connect to charging - some models (Redmi 9A, POCO M3) turn on automatically when charging. If not, use testpoint (requires disassembly). TVs: Unplug for 1 minute, then plug in - some models (Mi TV 4A) run without a button. Smart devices: Columns and lamps can be turned on via the Mi Home app (if they were tied before reset). If the power button is physically damaged, repair in the service (replace the button or plug).

Setting reset deleted all the photos. Can you restore them?

When you completely reset (via Recovery or Wipe All Data), the data is deleted irrevocably. However, there is a chance to recover some of the files: If the reset was done through the settings menu (soft reset), try programs like DiskDigger or Recuva (for root-access devices only!). Check backups in Mi Cloud (if sync was enabled): cloud.mi.com. For Mi TVs TV Photos can be saved on the connected USB-accumulator. ⚠️ Do not write new data to your device after a reset – this reduces the chances of recovery!