Smartphone Xiaomi Mi 10 Pro — the flagship of 2020 with a powerful processor Snapdragon 865, but even such a device may not turn on for various reasons: from banal discharge to software failures. If your device does not respond to the power button, do not rush to panic — in 90% of cases, the problem is solved without contacting the service center.
In this article, we will look at all possible scenarios, from standard on-line to recovery after a critical failure, focusing on hardware buttons, keyboard shortcuts and fault diagnosis, and how to distinguish a software failure from a hardware failure, which will save time and money.
If you just bought a Mi 10 Pro used or pulled it out after a long storage period, check the battery first. Even a fully discharged battery can wake up after 10-15 minutes of connecting to the original charger.
Standard inclusion: power button and nuances
In most cases, the inclusion of the Xiaomi Mi 10 Pro is no different from other smartphones: just press the power button for 2-3 seconds.
- 🔋 If the battery is discharged to 0%, first 5-7 The screen may not respond for minutes after charging. Wait for the charging indicator to appear (red battery).
- ⚡ Use the original power supply unit 30W Compatible with Quick Charge 4+. Cheap charging may not give enough current to start.
- 🕒 When you first turn on after buying or resetting, the system can “think” up to 1 minute – this is normal.
If nothing happens after pressing the power button, try an alternative combination: press the power button and volume up for 10-15 seconds at the same time, which will force the device to restart, even if it is getting stuck at the firmware level.
💡
If the smartphone doesn’t respond to the buttons, plug it into charging and leave it for 30 minutes. then try turning it on by holding the power button + volume down – this sometimes works when you’re deep-discharged.
Note the charging indicator: if it flashes red, the battery is critically discharged, yellow is charging, green is charging complete. If no indication is given, check the cable and USB-C connector for damage.
Forced reboot: when the smartphone freezes
If the Mi 10 Pro is stuck on the Xiaomi logo, black screen or does not respond to touch, hard reset will help.
- Hold the power button + volume up for 15-20 seconds.
- Release the buttons when the screen goes out (usually 10-12 seconds later).
- Wait for 30-60 seconds – the device should automatically restart.
If the smartphone then hangs on the logo again, this may indicate firmware damage, in which case you will need to flash through Fastboot or Recovery.
To diagnose the hangings, check:
- 📱 Have the latest updates been installed? MIUI (Go to Settings. → The phone. → Updating the system).
- 🧹 Is there enough free memory (less than 1 GB can cause lags).
- 🔄 Are there any third-party apps in conflict (try downloading into Safe Mode).
Incorporation after deep discharge or long storage
The Mi 10 Pro battery (capacity 4500 mAh) is sensitive to deep discharge. If the smartphone has been discharged for more than 2-3 weeks, the battery controller can block charging.
Leave it on charge. 30-60 minutes (even if there is no reaction)|Try another charger (minimum) 18W)|Press and hold the power button 30+ seconds|Connect to the PC through USB (Sometimes it helps to wake up the controller)-->
Critical information: if after an hour of charging the indicator does not light up, do not try to disassemble the smartphone yourself - this can lead to a short circuit.
When you successfully "wake up" after a deep discharge:
- Wait for full charge (up to 100%).
- Perform 2-3 discharge/charging cycles to calibrate the battery.
- Check the state of the battery in Settings → Battery → Battery condition.
If the battery capacity is less than 80% of the original, consider replacing the original battery for the Mi 10 Pro with an MB-J20 article.
Launch in Recovery and Fastboot mode
If the smartphone doesn't turn on normally but responds to button combinations, you can try running it in service modes, which allow you to reset your settings, reflash the device or diagnose hardware problems.
| Regime. | Button combination | Appointment |
|---|---|---|
| Recovery | Food + Volume up | Reset settings, clear cache, install updates via ADB |
| Fastboot | Food + Volume Down | Flashing through the PC, unlocking the bootloader, testing hardware components |
| EDL (9008) | Only through test points or a special cable | Recovery after “bricking”, flashing through Qualcomm Tools |
In Recovery mode, you can:
- 🔄 Select Reboot system now for normal reboot.
- 🧹 Cleaning cache (Wipe cache partition) – this often solves problems with hanging.
- ⚠️ Perform reset to factory settings (Wipe) data/factory reset – all data will be deleted!
How to exit Fastboot if the smartphone is stuck in this mode?
To work with Fastboot you will need:
- Install Platform Tools from Google.
- Connect your smartphone to your PC via the original cable.
- Open the command line in the folder with adb and fastboot.
Diagnostics of hardware problems
If none of these things worked, there may be a hardware problem.
⚠️ Warning: Do not disassemble the smartphone yourself - this will void the warranty (if it is still valid) and can damage the plumes. Xiaomi Mi 10 Pro has a fragile design with adhesive battery mount.
Typical hardware faults:
- 🔌 Faulty connector USB-C (Check for oxidation or mechanical damage).
- 🔋 Bloating or battery failure (visually visible by deformation of the back cover).
- 🛠️ Damage to food boards (often occurring after falls or moisture hits).
- 📱 Power button malfunction (diagnosed by lack of tactile response).
To check the power button:
- Connect your smartphone to charging.
- Carefully press the power button - there should be a clear click.
- If the button "fails" or is not fixed, it must be replaced.
If you suspect damage to the fee, pay attention to:
- 🌡️ Overheating of the body in the processor area (can be checked by hand after 5 minutes of charging).
- 💡 Extraneous odors (burn indicates burned elements).
- 🔊 Extraneous sounds (squeaking or crackling when connecting charging).
Frequent User Mistakes and How to Avoid Them
Many of the problems with the Mi 10 Pro are caused by the wrong actions of users, and here are the most common mistakes:
- ⚡ Using non-original chargers: Cheap power supplies can not only slowly charge, but also damage the battery controller.
- 🔄 Interrupt system updates: If the smartphone is updated via Recovery, it cannot be turned off until the process is complete.
- 🛠️ Self-disassembly without tools. The Mi 10 Pro requires special suction cups and mediators to keep the plumes intact.
- 📱 Install custom firmware without unlocking the bootloader, which leads to the "bricking" of the device.
To avoid problems:
- 🔋 Update regularly MIUI through settings → The phone. → Updating the system.
- 📱 Do not install applications from unverified sources (risk of viruses causing hangovers).
- 🛡️ Use cushioned cases – Mi 10 Pro has a glass case prone to cracks.
💡
If the smartphone stopped turning on after falling or getting moisture, immediately disconnect it from charging and do not try to turn on.A short circuit can disable the motherboard.
If you plan to sell or transfer a smartphone, reset to factory settings via Settings → About Phone → Reset. This will delete all data and untie your Mi Account, which is important for the new owner.