How to unlock the Xiaomi 1S scooter: all working ways in 2026

Xiaomi Mi Electric Scooter 1S is a popular theft-proof model, but sometimes owners experience unexpected locking. The reasons range from a firmware failure to a factory password activation after buying used equipment. In this article, we will discuss all current unlocking methods, including official methods through the Mi Home app and alternative solutions for complex cases.

It is important to understand that the procedure for unlocking depends on the type of lock, for example, hardware lock (through a lock). BLE-The module requires one approach and the software one (via the app) the other, and we'll look at both options, and we'll give you recommendations to prevent re-blocking. If you bought a scooter with your hands and the previous owner didn't untie it from your account, you'll find a solution here, too.

Before you start, check:

• 🔋 Battery level (minimum 20% for stable operation)
• 📱 Mi Home version (update to the latest version)
• 🔄 A backup of settings (if the scooter was previously linked to your account)

1.Official unlock through Mi Home

The safest way is to use a proprietary app, which is suitable if the scooter is blocked because of:

• 🔐 Entering the wrong password 3 times in a row
• 📲 Loss of communication with the phone (automatic locking)
• 🔄 Failure after firmware update

Instructions:

1. Open Mi Home and go to Profile → My Devices.
2. Select your Xiaomi 1S (if it doesn’t show up, click Add Device and do the anchor again).
3. In the device menu, find the item Security → Unblock.
4. Follow the system prompts (you may need to enter a password from your Mi Account).

If there is no safety section:

• 📌 Check the region in the app (should match the region of the scooter purchase).
• 📌 Update the scooter firmware through Settings → Update of the PO.

Make sure the scooter is on and near the phone (within a radius of 5 m)

Check your phone’s internet connection (Wi-Fi or mobile data)

Disable VPN (can block access to Xiaomi servers)

Charge your phone to at least 50% (in case of a long procedure)

-->

⚠️ Note: If the scooter was tied to someone else's Mi Account (for example, when buying a used one), official unlocking via Mi Home is not possible.

2. Resetting to factory settings (hardware reset)

This method works if:

• 🔄 The scooter does not respond to commands from the application
• 🔐 Previous owner did not untie the device from his account
• 📱 Mi Home app does not see scooter or gives an error Device is locked

Resetting will require physical access to the buttons on the scooter.

1. Turn off the scooter with a long press on the power button (5 seconds).
2. Press the power button and the brake button (on the steering wheel) at the same time.
3. Hold for 10-15 seconds until the white light lights up (first red, then white).
4. Release the buttons - the scooter will reset and reboot.

After discharge:

• 📱 The scooter will be disconnected from all Mi Account accounts.
• 🔧 All settings will return to factory settings (including speed limits).
• 🔄 Repeat the re-tiring via Mi Home.

3. Unlocking through firmware (alternative method)

If the standard methods didn't work, you can try reflashing the scooter controller.

• 🔐 Blocking at the firmware level (for example, after a failed update)
• 📱 Scooters tied to other people's Mi Accounts
• 🔧 Devices with damage BLE-module

The firmware will require:

• 💻 Windows computer 10/11
• 🔌 USB-Type-C Cable (to connect to the controller)
• 📦 DownG (or ScooterHacking Utility)
• 📄 Firmware for Xiaomi 1S (The version should match your model!

Step-by-step:

1. Download and install DownG from the official website.
2. Connect the scooter to the computer via the Type-C port (located under the lid on the steering wheel).
3. Launch DownG.
4. Press Start Flash and wait until it is completed (don’t turn off the cable!).

💡

Before you install the firmware, disable the antivirus, which can block DownG as suspicious software, and it is also recommended to use the original Xiaomi cable, as cheap analogues can cause data transmission errors.

⚠️ Attention: Incorrect firmware can lead to a complete loss of performance of the scooter ("bricking"). If you are not sure about your actions, contact the service center.

4 Unlocking through replacement BLE-module

BLE-The module (Bluetooth Low Energy) is responsible for linking the scooter to the phone and storing the lock data, and if all software methods are exhausted, then the physical replacement of the module remains.

How to determine if the problem is BLE-module:

• 📱 Scooter does not connect to Mi Home, although the indicator is on
• 🔄 Resetting settings doesn't help
• 🔊 When turned on, uncharacteristic sounds (squeaks, cods) are heard)

Instructions for replacement:

1. Remove the steering wheel by unscrewing 4 screws under the lid (a PH2 cross screwdriver will be required).
2. Disconnect the battery (required!) to avoid short circuit.
3. Find it. BLE-module (small board with antenna, usually next to the main controller).
4. Carefully unseal the old module and install a new one (you can buy it on AliExpress or in service centers).

Cost of new BLE-module 1S — 800 to 1500 rubles. note that after the replacement will be required:

• 📱 Re-tied scooter in Mi Home
• 🔧 Set speed limits and driving modes

Officially via Mi Home|Hardware discharge|Firmware through DownG|Replacement BLE-module|I haven't tried it yet.-->

5. Frequent mistakes and how to avoid them

Many users experience the same unblocking problems, and here are the most common errors and ways to resolve them:

• 🔴 Mi Home: The scooter is not in pairing mode or conflict with another device Solution: Turn off Bluetooth on your phone, restart the scooter and re-tether.
• 🔴 After the scooter is reset, the reason: Discharged battery or controller failure Solution: Connect charging for 30 minutes, then reset.
• 🔴 Firmware interrupted by 50% Cause: Unstable connection USB Solution: Use the original cable and disable the antivirus.

Another common problem is that the scooter locks itself immediately after unlocking.

• 📱 Mi Home has enabled Autolock when disconnected.
• 🔋 Charge level below 15% (the system automatically blocks the scooter to save energy).

💡

Before any unlocking procedure, check the battery level. At a level below 20%, the risk of failure increases 3 times.

6.How to prevent re-blocking

To avoid repeated problems, follow these guidelines:

• 🔐 Untie the scooter from your old account before selling: Mi Home → Profile → My devices. → Xiaomi 1S → Remove the device.
• 📱 Update the firmware only through the official application (do not use third-party firmware!).
• 🔋 Do not drain the battery to 0% – this can cause a controller to fail.
• 🔑 Set a strong password in the scooter settings (do not use standard combinations like 0000).

If you are buying a used scooter, be sure to check:

• 📌 Is it untied from your previous Mi Account.
• 📌 No physical injuries BLE-module (cracks, oxidation of contacts).
• 📌 Does the serial number on the case match the data in Mi Home.

For additional protection, you can activate two-factor authentication in your Mi Account, which will make it harder for unauthorized access to the device.

FAQ: Answers to Frequent Questions