Xiaomi Redmi Note 8T is a popular smartphone with powerful hardware, but sometimes its owners face the unexpected inclusion of the Fastboot mode. This engineering mode can be activated after a failed update, reset settings or even accidentally pressing buttons. If your Redmi Note 8T is getting stuck on the screen with a rabbit in a hat-eared and FASTBOOT inscription, do not panic: we will detail how to get out of this mode and turn off Fastboot autoboot forever.
In this article you will find:
- π§ 3 working ways to disable Fastboot including the method without a computer)
- π± Step-by-step instructions with pictures and commands for ADB
- β οΈ What to do if the smartphone does not respond to buttons or hangs
- π How to prevent accidental Fastboot turn on in the future
Before you start, make sure you have access to the charger β a discharged battery during manipulation with the Fastboot can lead to the βbrickingβ of the device. If the battery is discharged below 30%, first recharge the smartphone for at least 15-20 minutes.
What is Fastboot on Xiaomi and why does it turn on itself?
Fastboot (or bootloader) mode is a low-level Android device boot mode designed to:
- π Installation of custom firmware (custom) ROM)
- π Unlock the loader (OEM Unlock)
- π οΈ System Recovery After Failures
- π± Firmware of individual partitions (for example, recovery or boot)
On the Redmi Note 8T (model M1908C3XG), the Fastboot can be activated automatically in the following cases:
| Reason. | How it happens. | Decision |
|---|---|---|
| Misfitting MIUI update | Interrupted firmware via Updater or Recovery | Check out the Mi Flash Tool. |
| Reset to factory settings | Error with Wipe Data in Recovery | Run fastboot erase userdata |
| Accidental push of buttons | Volume Down + Power when enabled | Select Normal Boot from the Fastboot menu |
| Damaged loader | After a failed OEM unlock | Switch the original boot.img |
If your Redmi Note 8T loads into the Fastboot every time it turns on, the problem is likely to be a damaged boot partition or incorrect boot boot settings, in which case you will need to flash it.
Method 1: Exit from Fastboot without computer (buttons)
If the smartphone just hovers in Fastboot mode, but physically reacts to button presses, try the standard method:
- Hold the power button for 10-15 seconds until the screen goes out.
- After the vibration, immediately press the combination: Volume Up + Power Hold until the MI logo appears.
- In the Recovery menu, select Reboot β System (use volume buttons for navigation and Power for confirmation).
If after these actions the smartphone is loaded again in Fastboot, then the problem is deeper β perhaps damaged bootloader or system files.
βοΈ Preparing to exit Fastboot
Method 2: Disable Fastboot via ADB (for power users)
If the smartphone periodically goes to Fastboot, but sometimes boots into the system, you can turn off the autoboot of this mode via ADB (Android Debug Bridge).
- π₯οΈ Computer with Windows/Linux/macOS
- π USB-cable (preferably original)
- π¦ Installed drivers Xiaomi and ADB Tools
Instructions:
- Turn on your smartphone to debug USB: Settings β About Phone β MIUI Version (click 7 times) Settings β Additional β For developers β Debugging by USB
- Connect the Redmi Note 8T to your PC and confirm debugging permission.
- Open the command prompt (cmd) and type: Adb devices Make sure the device is defined.
- Fastboot: Adb shell settings put global fastboot_autoboot_disabled 1
- Reboot your smartphone: adb reboot
If the problem persists after the reboot, try resetting the Fastboot settings to factory:
adb shell settings delete global fastboot_autoboot_disabledπ‘
If ADB canβt see the device, try reinstalling drivers via the Mi Unlock Tool or using a USB 2.0 port (on some PCs, USB 3.0 doesnβt work well).
Method 3: Flashing through the Mi Flash Tool (if the smartphone is not turned on)
If the Redmi Note 8T is fixated on Fastboot and doesnβt respond to other methods, you just have to flash it through the official Mi Flash Tool, which is suitable even if:
- π΄ The screen doesn't respond to touch.
- π The smartphone is constantly rebooting.
- β οΈ Invalid Partition Table or No Command Error
Step-by-step:
- Download the official firmware for Redmi Note 8T (select the Fastboot version, not Recovery!).
- Unpack the archive into a folder without Cyrillic characters (e.g., C:\MIUI\).
- Download and install the Mi Flash Tool.
- Turn off your smartphone (press the Power + Volume Down for 20 seconds).
- Hold Volume Down + Power and plug in USB-cable to PC β the device must be defined as Qualcomm HS-USB QDLoader 9008.
- In Mi Flash Tool, click Select, specify the firmware folder, select Clean All mode and click Flash.
The process will take 5-10 minutes. Once completed, the smartphone will automatically restart in normal mode.
What to do if the Mi Flash Tool is in error?
Frequent Mistakes and How to Avoid Them
When working with Fastboot on Redmi Note 8T, users often face the following problems:
β οΈ Warning: If the phone doesn't turn on after firmware for more than 10 minutes, don't turn off the cable! Wait for the process to be completed (indicator - green checkmark in Mi Flash Tool). EMMC-chip.
| Mistake. | Reason. | Decision |
|---|---|---|
| Device not found in ADB | No drivers or USB-debugging not included | Reinstall drivers, check debugging over USB |
| The smartphone vibrates, but does not turn on | Boot or recovery section damaged | Switch to the Mi Flash Tool in Clean All mode |
| Invalid sparse file format at header | Firmware archive damaged | Download the firmware again, check the checksum MD5 |
| Hanging on the MI logo | Module conflict after firmware | Run Wipe Data in Recovery |
If after all the manipulations Redmi Note 8T still loads in Fastboot, check:
- π Battery charge (minimum 50% for firmware)
- π Cable and port USB (Try another cable or port)
- π₯ The firmware version (must conform to the model) M1908C3XG)
How to prevent accidental Fastboot turn on in the future
To avoid repeat issues with the Fastboot on the Redmi Note 8T, follow these tips:
- π Update. MIUI Only through the official Updater (not through Recovery, unless you are sure of the firmware).
- π§ Do not accidentally press buttons when you turn on your smartphone (especially Volume Down). + Power).
- π± Turn off automatic reboot in Developer Mode: Settings β Additionally. β For developers β Automatic reboot (disable)
- π Do not unlock the bootloader unnecessarily (this increases the risk of crashes).
If you often experiment with firmware, back up the boot and recovery section via ADB:
adb shell
su
dd if=/dev/block/bootdevice/by-name/boot of=/sdcard/boot.img
dd if=/dev/block/bootdevice/by-name/recovery of=/sdcard/recovery.imgThese files can be restored in the event of a failure.
π‘
If your Redmi Note 8T doesnβt turn on after all the manipulations, contact the service center, possibly a problem in the hardware (for example, damaged memory EMMC or power controller).