How to remove Fastboot on Xiaomi: the complete guide

The sudden appearance of the logo of a hare repairing an android and the Fastboot on the screen of a Xiaomi smartphone often takes users by surprise. This state of panic is understandable, because the device stops responding to normal touches and does not load the usual interface. However, in most cases, MIUI or HyperOS are not damaged, and the phone simply went into a special low-level diagnostic mode.

This feature was originally designed by engineers to run devices through a computer, but it's a common occurrence, usually the result of improperly pressing a combination of buttons in your pocket or bag when the device is turned off, and understanding the nature of this mode is the first step to successfully restoring the gadget to normal operation.

There are several proven ways to get out of this state, from simple reboots to specialized software. It is important not to panic and not to look for a service center right away, since a software failure rarely means a physical motherboard failure. In this article, we will discuss in detail the algorithms of actions for various scenarios.

Reasons for getting into Fastboot mode

To effectively fix the problem, you need to understand what caused the system to go into diagnostic mode. The most common and common reason is mechanical impact. When the smartphone is off, simultaneous or sequential pressing of the on and down buttons activates this mode, often unnoticed by the owner.

The second scenario involves software errors during the system update: If a new MIUI version fails or interrupts, the bootloader may not find the main system and automatically switch to firmware standby, and conflicts may arise after installing custom recavators or obtaining Root rights.

💡

Check your smartphone's protective case. Too tough or low-quality cases often press on the side buttons, causing random entry into the Fastboot when the screen is locked.

The third group of causes is hardware malfunctions of the buttons, and if the volume button is stuck due to moisture, dirt, or just physical wear, the phone will go to the Fastboot every time you try to turn on, and in such cases, software methods may not help, and you will need to repair the plume.

• 🔘 Accidental pressing of a combination of buttons in your pocket or when carried in a bag.
• 🔄 Failure in the process of automatic updating of the operating system.
• 💧 Getting moisture or dust under the volume buttons, causing a circuit.
• 🛠️ Incorrect operation of a modified bootloader or third-party Recovery.

The easiest way to exit: reboot buttons

In the vast majority of cases, when the phone is working, you just have to do a forced reboot, which is safe and doesn't require a computer connection or special skills, and you only need physical access to the device control buttons.

The algorithm is simple: you need to press the Power button and hold it for a long time, usually in 10 to 20 seconds, and the screen should go out, and then the MI or Redmi logo will appear, marking the beginning of the normal boot system.

If holding the power button didn't work the first time, try the combination: Press the Power and Volume Up buttons at the same time. Hold them for about 15 seconds. This combination is often used as an alternative method of Hard Reset or reboot on Xiaomi devices.

⚠️ Attention: Don't confuse volume buttons. To exit from Fastboot, you often need a volume button paired with power, whereas to enter, you need to decrease. Using the wrong combination can return you to firmware mode.

Use of the computer and ADB utility

If the buttons on the device are unresponsive or damaged, you can try the software method of exiting the mode via the computer, which requires a USB cable and installed ADB drivers (Android Debug Bridge), which is more reliable, as it eliminates the mechanical factor.

You first need to make sure that the computer sees the device. Even in Fastboot mode, the phone is defined by the system as a connected device, although not as a drive. You need to download the minimum set of platform-tools tools from the official Android developer site.

After connecting the phone to the PC through USB-cable, open the command line in the tool folder ADB. Enter a command to check the connection:

adb devices

If the device appears in the list (even if it is unauthorised or fastboot), the connection is established. For a forced reboot, use the following command:

adb reboot

This method is particularly useful when the power button is physically broken or crashed, and the team sends a signal directly to the power controller, ignoring the state of the physical keys, but if the problem is a deep software failure of the bootloader, this method may not work.

Table of methods of solving the problem

To organize your knowledge and choose the best way to recover, use the table below to quickly determine the appropriate method, depending on your situation and the tools available.

As you can see from the table, the simplest methods do not carry the risk of data loss, and it is worth switching to radical measures, such as firmware, only if a software failure does not allow the system to boot itself after leaving Fastboot.

It’s worth noting that the effectiveness of methods can vary depending on your Xiaomi, Redmi or Poco model. On older devices, mechanical reboot works almost always, whereas newer models with reset protection may require more complex manipulations.

What to do if your phone goes back to Fastboot

When the phone goes back to Fastboot mode after a successful restart, it points to a bigger problem, most often a failure of the volume button, and the mechanical closure of the contacts is perceived by the processor as a command to enter firmware mode immediately after power is applied.

In these cases, you can try tapping your finger gently on the button area or pressing it slightly in different directions to try to "mix" the contacts, and if that helps at least temporarily, then the problem is the mechanics.

If the buttons are good but the reboot cycle continues, the bootloader partition or system files may be damaged, in which case a complete flashing of the device with data cleaning may be required, using the official Mi Flash Tool utility and the Fastboot firmware image.

⚠️ Warning: If the phone gets caught in an endless Fastboot cycle after falling or falling into water, do not plug it into charging.This can cause a short circuit and permanently disable the motherboard.

Prevention and diagnosis of buttons

To avoid a repeat of the situation, you should do prevention. First of all, check the movement of the volume buttons. They should have a clear, elastic click. If the button is sliding in without clicking or, on the contrary, it goes too tight, this is the first sign of an imminent failure.

Use the diagnostic engineering test menu. Type ##64663## in the phone app (if you have access to the interface) and select a button test to determine exactly if a click is logged software.

It is also recommended to back up important data regularly. While logging out of Fastboot is usually safe, any manipulation of the bootloader carries potential, albeit minimal, risks. Having a backup in the Google or Mi Cloud cloud will save your photos and contacts.

• 🧹 Regularly clean the button area of dust and pile with a soft brush.
• 📱 Use high-quality covers that do not create excessive pressure on the side face.
• 💾 Make backups of data before any system updates.
• 🔋 Watch the battery condition, as the bloating of the battery can press on the button plumes.

💡

If the problem with the buttons is confirmed, self-disassembly of the smartphone can deprive you of an official warranty.

When needing specialist assistance

There are situations where trying to remove Fastboot on Xiaomi on your own is useless or dangerous. If none of the software methods work and the phone does not respond to ADB commands, most likely the problem lies at the hardware level.

Also, the help of a master is necessary if the device was flooded with liquid, and attempts to turn on such a phone can lead to electrolysis and corrosion of components, in which case professional cleaning in an ultrasound bath and multimeter diagnostics are required.

Don't ignore the problem if the phone goes into the Fastboot on its own for no apparent reason, which can eventually turn on the device completely, and it costs significantly less to replace the button plume in a timely manner than replacing the motherboard.