Replacement of glass with Xiaomi Redmi 9T: 2026 prices, where to repair and how to save money

Xiaomi Redmi 9T It remains one of the most popular budget smartphones, even years after its release — reliable, productive, with a good battery, but like any touchscreen device, it is vulnerable to falls and scratches. Not only does broken glass ruin the look, it can also disable the touchscreen or the display completely. 9T In 2026, where is it better to repair it, whether it's in a service, in a private workshop, or if you try to do it yourself? In this guide, we'll look at all the options with the current prices, pros and cons of each one.

It is important to understand that by "glass replacement" often mean different procedures: peeling off the protective glass (if any), replacing the touchscreen (touch layer) or completely replacing the display module. 9T glass and touchscreen are usually soldered with the matrix into a single unit, which complicates repairs and affects the price. Next, we will understand what exactly breaks when you fall, how much will it cost to repair in each case and how not to run into poor-quality parts.

What exactly breaks when broken glass on Redmi 9T?

When you drop your phone, damage can be different, from small cracks to a complete failure of the screen. - Xiaomi Redmi 9T (model M2010J19SG) used IPS-resolution-screen 2340×1080 frequency 60 Hz, soldered to the touchscreen, and these are the scenarios that are possible:

• 🔹 Cracks on the glass without disrupting the work - the screen turns on, the touch screen responds to touch, but you can see chips or spiders, in which case you can do with replacing only the protective glass (if it was glued) or the top layer.
• 🔹 The touchscreen is damaged, the screen is working but does not respond to touch (or partially responds), and you will need to replace the touch module that is on the Redmi. 9T goes with the matrix.
• 🔹 If you break the matrix, you have stripes, you have a shimmer, you have a shimmer, or you don't turn it on at all, and that's the most expensive thing you'll ever do, because you'll have to change the entire display module.
• 🔹 The plume is damaged, so the screen can flash, turn off spontaneously, or show artifacts, sometimes it helps to reconnect the plume, but more often it also changes.

In practice, in 80% of cases, when a strong impact breaks it is the display module as a whole (glass). + touchscreen + It's a bit of a matrix, because it's bonded, and it's possible to replace the glass separately, but it's very risky, and it requires special equipment to separate the layers, and after that repair, there are often defects (bubbles, uneven lighting).

⚠️ Warning: If the phone stops turning on after the fall or the screen flashes, don't be in a hurry to change the display! The power plume or the battery may have gone away.

How much does it cost to replace glass with Redmi? 9T 2026: Prices in services

The cost of repairs depends on what you change and where you do it. Below are the current prices for Moscow and the regions (data for June 2026). Note that official Xiaomi services often overprice, and in private workshops you can run into poor-quality parts.

Important: In official services, Xiaomi often insists on replacing the entire display module, even if only the touchscreen is damaged. 30–50%. In private workshops you can find more flexible options, but the risk of running into a fake is higher (OEM/Aftermarket).

Prices in the regions may vary ±15-20%, for example, in St. Petersburg and Yekaterinburg, repairs will cost 10-15% more than the average in Russia, and in small cities - cheaper.

Private workshop vs. official service: where is the best?

Choosing between a formal service and a private workshop is always a trade-off between price, quality and warranty, and we'll look at the pros and cons of each option for Redmi. 9T.

✅ Official Xiaomi service

• ✔️ 6-12 months warranty for work and spare parts (in private workshops usually 1-3 months).
• ✔️ Use original parts (but not always – sometimes put on) OEM-analogue).
• ✔️ Diagnosis is free (in most cases).
• ✔️ You can check the history of repairs through the official website.

Cons:

• ❌ It is more expensive by 30-50% compared to private.
• ❌ Long periods – from 3 to 7 days (in private workshops often do 1-2 hours).
• ❌ Not always agree to partial repairs (for example, only a touchscreen replacement).

✅ Private workshop

• ✔️ Prices are 20-40% lower (especially if you use spare parts).
• ✔️ Quick repairs – often in 1-2 hours.
• ✔️ You can arrange partial repairs (for example, only glass replacement).

Cons:

• ❌ The risk of running into poor quality parts (especially if the workshop offers too low a price).
• ❌ The warranty is usually 1-3 months (or no warranty at all).
• ❌ No verification of originality of details.

How to choose a reliable workshop?

⚠️ Note: If the workshop offers a replacement display on Redmi 9T less₽ — It's a good idea to be wary, and you'll probably get a low-quality copy that lasts a couple of months, and the original display module can't cost less than 2,000.₽ wholesale.

Can I replace the glass with Redmi? 9T independently?

Theoretically, yes, but in practice, it's extremely risky. 9T glass is soldered with a touchscreen and matrix, and to replace it you need to:

1. Disassemble the phone (risk of damaging the plumes or battery).
2. Separate the glass from the matrix using special equipment (infrared station or hair dryer with precise temperature control).
3. Clean the glue residues and paste new glass without bubbles.
4. Reassemble the phone by checking all connections.

Without experience, you risk:

• 🔥 Damage to the matrix (it is afraid of overheating).
• 🔌 To break the plumes (they are very fragile).
• 💧 Leave bubbles or dirt under new glass.
• ⚡ Disable the battery (if it is shorter during assembly).

If you do decide, here's what you'll need:

• 🛠️ New glass (original or quality copy, for example, from the BROTECT Nillkin).
• 🔥 Fen or IR station for heating glue.
• 🧲 Suction and shoulder blades for careful removal of glass.
• 🧴 Clay. B-7000 or LOCA fixing.
• 🔍 Lupa or microscope to check connections.

Cost of spare parts for self-replacement:

• 💎 Protective glass (if you only need it) – 200-500₽.
• 📱 Display module (original) – 2,500–3,500₽.
• 📱 Display module (copy) – 1,800–2,500₽.
• 🔌 Display plume - 300-600₽.

If you’ve never repaired your phones before, don’t try – saves 1,000-1,500₽ You don't have to risk being left without a work phone.

How to Save Money on Glass Replacement: 5 Ways to Work

Replacement of the display with Redmi 9T It can be a tidy sum, but there are ways to reduce costs without risking the phone:

1. Look for shares and discounts
2. Buy the parts yourself.
3. Choose. OEM-Parts instead of the original
4. Combine the repairs
5. Check insurance.

💡

Before you change the display, back up your data! Even if the phone turns on, there's a risk of damaging your memory when you disassemble it. Use Settings → System system → Backup or Mi program PC Suite.

Frequent mistakes when replacing glass with Redmi 9T

Even in service centers, sometimes mistakes are made, which then lead to new breakdowns, and this is what you should pay attention to in order not to run into poor repairs:

• 🚫 Use of cheap glue - if the master saved on glue (for example, used ordinary superglue instead of the same glue). LOCA or B-7000), Over time, the glass will peel off or bubbles will appear.
• 🚫 Wrong temperature when glued - if you overheat the matrix, it can lose brightness or start to blink.Optimum temperature for Redmi 9T — 80–90°C.
• 🚫 Train damage – if the master pulled the plume too hard during disassembly, over time artifacts may appear on the screen or it will stop turning on.
• 🚫 Installation of incompatible display – sometimes install modules from other models (for example, from Redmi 9 or other models). POCO M3), They are similar in appearance, but have other connectors.
• 🚫 No check after repair – a good master will definitely test the touchscreen, camera, speakers and microphone after assembly.

How do we avoid these problems?

• 🔍 Ask what type of glue is used, it should be. LOCA or B-7000.
• 🔥 Clarify how the glass will be separated - a hairdryer or IR station should be used, not an open fire.
• 📋 Ask for a check with a list of jobs so you can make a claim if something goes wrong.
• 🕵️ Check the reviews about the workshop - especially pay attention to complaints about repeated breakdowns.

💡

If the screen becomes less bright after changing the glass, there are divorces or broken pixels, this is a sign of overheating of the matrix, in which case you need to immediately return the phone to the workshop and demand a rework under warranty.

Where to buy spare parts for Redmi 9T: shop-tested

If you are choosing to replace the glass or display yourself or buy parts for the master, it is important to choose a reliable supplier.

When buying, pay attention to:

• 📌 Model name – should be specified by Xiaomi Redmi 9T M2010J19SG.
• 📌 Type of display - original (original), OEM (High Copy (or copy) (Aftermarket).
• 📌 Set – the set should include glue, suction cups and shoulder blades (if you buy for self-replacement).
• 📌 If the seller has less than 4.5 stars, it is better to look for another option.

If you buy a display module, ask the seller for a photo of the plume connector, which must match the original. 9T used 30-pin connector, not 20-pin, Like some other Redmi models.

FAQ: Frequent questions about replacing glass with Redmi 9T