Your Xiaomi screen crashed, vertical stripes appeared, or the image began to flicker? Most likely, the matrix is the most expensive display element. The cost of repairing it can vary from 2,000 to 20,000 rubles depending on the model, type of matrix and repair site. In this article, we will discuss why prices differ so much, where to repair (Mi Service, third-party services or yourself), and how not to run into scammers who will sell you used parts at the price of new ones.
It's important to understand that replacing a matrix is not the same as replacing a glass. If there are only cracks on the screen, but the image works, you need to replace the touchscreen, which is 2-3 times cheaper. If the screen does not respond to touch, shows artifacts or does not turn on, the problem is in the matrix. Next, we will analyze all the nuances so that you can make an informed decision.
What is a matrix in a smartphone and why it breaks
The Matrix is OLED- or AMOLED-panel (in older models β IPS LCD), It's made up of millions of pixels, backlights and control electronics, and unlike glass, which protects the screen from the outside, the matrix is inside, and it's responsible for color reproduction, contrast and brightness.
The main causes of breakdown:
- π₯ Mechanical damage: falling to a hard surface, a strong impact (even if the glass is whole, the matrix can crack inside).
- π‘οΈ Overheating or hypothermia: leaving your phone in the sun or in the cold can cause layers of the matrix to detach.
- β‘ Voltage surges: A faulty ROM or a sharp battery discharge of up to 0% sometimes disables the matrix controller.
- π οΈ Poor-quality repair: if the master damaged the plume or improperly connected the display when replacing the glass.
How do you know if it's a matrix that's broken, not a glass or a plume?
- π΅ The screen is not turned on, but the phone vibrates / sounds are there.
- π¨ Image is available, but the colors are distorted (pink/green hue).
- π Vertical/horizontal bands, flickering, "broken" pixels.
- π The sensor is working, but the image is missing or partially.
How much does it cost to replace the matrix in the official Mi Service service?
Official Xiaomi service centers (the list can be found on the website) mi.com/ru/service/center) Use original parts and give a guarantee to 12 But the prices are higher than in the informal workshops, sometimes in the 1,5β2 once.
Current prices for 2026 (including work and spare parts):
| Xiaomi model | Type of matrix | Cost (β½) | Duration of repairs |
|---|---|---|---|
| Redmi Note 12 Pro+ | AMOLED, 120Hz | 12 000 β 15 000 | 3-5 days |
| POCO X5 Pro | AMOLED, 90 Hz. | 9 500 β 11 000 | 2-4 days |
| Xiaomi 13 Lite | AMOLED, 120Hz | 14 000 β 17 000 | 4-7 days |
| Redmi 10C | IPS LCD, 60 Hz | 4 500 β 6 000 | 1-3 days |
| Xiaomi 12T Pro | AMOLED, 120Hz | 16 000 β 20 000 | 5-10 days |
Important: Mi Service often offers to replace the entire display module (matrix) + glass + The frame, even if only the matrix is damaged, increases the price by 20 to 30 percent!
β οΈ Attention, official services may be denied repairs if the phone is not available:
- π It has a bloated battery (first it will be required to be replaced).
- π§ It was in unofficial repairs (can remove the warranty).
- π¦ It was in the water (even if it was a long time ago).
Prices in unofficial services: where cheaper and risks
Informal workshops can offer a matrix replacement 30 to 50 percent cheaper than Mi Service, but there are pitfalls:
- π Use used matrix (sometimes removed from broken phones) and give for new.
- π οΈ Poor quality soldering plumes - the screen may fall off in a month.
- π No guarantee or a βgreyβ guarantee (unofficial).
Average prices in unofficial services (Moscow, St. Petersburg, regions):
- Redmi Note 11/12: 6 000 β 9 000 β½ (original) / 3 500 β 5 000 β½ (analogue).
- POCO F4/F5: 8 000 β 11 000 β½ (original) / 5 000 β 7 000 β½ (analogue).
- Xiaomi 13/14: 12 000 β 16 000 β½ (Original only, analogues are rare).
How to choose a reliable workshop:
Has reviews on Yandex.Maps/2GIS (not less than one) 4,5 star)|
Offers a 6-month guarantee|
Shows the matrix before installation (can be checked for broken pixels)|
Uses a soldering station, not a plume dryer|
Gives a check indicating the matrix model-->
If you are offered a replacement for 2,000-3,000 β½ The minimum price of the original matrix for the Xiaomi 13 Pro starts from 10 000 β½ (workshop-buying).
π‘
Before repairing, ask the wizard to show the matrix in operation β connect it to the test phone. The original panel will have uniform backlight without yellowness at the edges.
Can I replace the matrix by myself?
Theoretically, yes, but in practice, it's extremely risky.
- Disassemble the phone (on some Xiaomi models, the glass is glued to the frame, and it is easy to damage).
- Seal off the matrix plumes (a soldering station and experience with microelectronics are required).
- Install a new matrix and glue it (needs a special glue). LOC or UV).
- Check the operation of the sensor and backlight (often after self-replacement there are "dead" zones).
Cost of tools and consumables:
- π§ Set of screwdrivers and mediators: 1000 - 1500 β½.
- π₯ Smelting station (e.g. Quicko) 861DW): 5 000 β 8 000 β½.
- π§΄ Clay. LOC or UV-curable: 500 - 1,200 β½.
- π± The matrix itself (on AliExpress): 3,000 β 10,000 β½ (risk of marriage).
β οΈ Attention! On Xiaomi models! 12/13/14 It's soldered to the power board of the display, and if you solder it in a sloppy way, you can burn the screen controller, and it'll cost you a lot of money to repair it. 20 000+ β½.
If you still decide to fix yourself, here is a step-by-step instruction for the Redmi Note 10 Pro:
Next articleInstructions for Redmi Note 10 Pro
Even if you have experience in electronics repair, replacing the matrix with a AMOLED-Xiaomi screens are more complicated than on older ones IPS. The point is, AMOLED-panels are thinner and more sensitive to static electricity.
Should I repair or buy a new phone?
Before you carry your phone for repair, consider the feasibility of spending it.
- If the cost of repair exceeds 50% of the price of a new phone, it is better to buy a new model.
- If the phone is older than 3 years, and repair will cost 70% of its cost - also unprofitable.
Examples for popular models (prices of new phones at the beginning of 2026):
| Model | The price of a new one (β½) | Cost of matrix repair (β½) | Is it worth fixing? |
|---|---|---|---|
| Redmi Note 12 Pro+ | 35 000 | 12 000 β 15 000 | β Yes, 34-43% of the price) |
| POCO X5 Pro | 28 000 | 9 500 β 11 000 | β Yes (34-39% of the price) |
| Xiaomi 13 Lite | 45 000 | 14 000 β 17 000 | β οΈ On the edge (31-38% of the price) |
| Redmi 10A | 12 000 | 4 500 β 6 000 | β No (38-50% of the price) |
Also consider the hidden costs:
- π If the battery is too high, it will have to be changed (+1 500 β 3 000 β½).
- π‘οΈ After repair, it may be necessary to replace the protective glass (+1 000 β 2 500 β½).
- π If the master damages the camera plume or speaker, repairs will cost even more.
π‘
Matrix repairs are only for flagships (Xiaomi) 12/13/14) Or the middle class phones are not older. 2 For budget models (Redmi) 10/9) It is more profitable to buy a new machine.
How to save money on repairing the matrix: 5 working ways
If you are determined to fix your phone, here are some legal ways to reduce your costs:
- Look for promotions in services: many workshops offer discounts of 10-20% in low season (January-February, August).
- Buy the matrix yourself: on AliExpress or in Chinese stores (for example, Kimovare), the original matrix is cheaper by 20-30%. NT37701 For the Redmi Note 11).
- Choose high quality analogues: some workshops install matrices from Samsung or BOE, which are not inferior to the original, but are 30% cheaper.
- Change in the complex: if you need to replace both the matrix and the battery, many services make a discount on the second repair.
- Check the warranty: If the phone is warranty and the screen is your fault, some services offer "warranty repair" with a surcharge (for example, 50% of the cost).
Here's what you shouldn't do:
- β Buying a matrix "with hands" on Avito - a high risk of getting a marriage or a used panel.
- β Agree to repair without diagnosis β the master can find βadditionalβ malfunctions.
- β Gluing a protective film instead of glass onto a matrix is a temporary solution that degrades the sensor.
Frequent problems after matrix replacement and how to avoid them
Even after a good repair, problems can occur, and here are the most common ways to fix them:
| Problem. | Reason. | Decision |
|---|---|---|
| The screen doesn't respond to touch. | Poorly soldered sensor plume or damaged controller | Re-sweeten the plume or replace the display power card |
| Yellowness at the edges of the screen | Low-quality glue or cheap matrix | Re-glue the matrix using LOC-glue |
| Screen flickering at low brightness | Incompatible matrix or poor plume contact | Replace the matrix with the original or reconnect the plume |
| Dead pixels or bands | Matrix marriage or damage during installation | Require a replacement under warranty (if any) |
If you have artifacts after the repair, don't rush out of the workshop.
- Check the density of the plumes (sometimes it helps to just reconnect them).
- Update the firmware of the phone (sometimes screen glitches are associated with the software).
- Test the matrix using the engineering menu (code ##6484## for Xiaomi).
β οΈ Attention, if the phone is running out faster after the matrix is replaced, it's likely that the wizard has damaged the battery or the power charge.