Replacement of glass on Xiaomi Redmi 8 Pro: prices 2026, where cheaper and how to save

Why the glass on the Redmi 8 Pro breaks and what to do

The screen Xiaomi Redmi 8 Pro — one of the most vulnerable points of the smartphone, despite the stated protection of Gorilla Glass 5. Fall from a height of 1-1.5 meters on the pavement, hitting a hard surface or even strong pressure in the pocket can lead to cracks, chipped or complete destruction of glass. Unlike flagship models, which uses the more durable Gorilla Glass Victus, budget Xiaomi smartphones are more likely to suffer from mechanical damage.

If your Redmi 8 Pro has cracks, but the sensor works and the image is displayed without distortion, you are lucky: just replace the top glass (touchscreen). If the screen does not respond to touch, the backlight flashes or colored stripes appear, the problem is deeper: most likely, the display module (OLED-matrix + sensor) is damaged and repair will cost more. In this article, we will discuss the exact prices for replacing glass in 2026, where it is better to repair and how to avoid fraud in services.

How much does it cost to replace glass on Xiaomi Redmi 8 Pro: price comparison

The cost of repair depends on three key factors: the type of spare part (original or analogue), the region (Moscow, St. Petersburg or regions) and the status of the service center (official or unofficial).

⚠️ Note: Original parts prices may vary due to the dollar. Xiaomi’s official services often offer a fixed turnkey repair cost – for example, 5,990 ₽ For a 6-month window replacement, informal workshops may overprice the work because of the complexity of the model, always check whether it includes diagnostics (sometimes it costs 300-500). ₽).

Previous Previous post: What to Choose for Redmi 8 Pro

Choosing between original glass and analogue is always a tradeoff between price, quality and durability.

• 🔹 Original Glass (Xiaomi):
• 🔹 Quality analogue (Tianma, BOE, Truly):
• 🔹 Budgetary analogue (no-name):

💡 Tip: If you plan to use a smartphone for another 1-2 years, the best choice is a high-quality analogue from Tianma or the Internet. BOE. It'll cost 2,500 to 3,000. ₽ It's a job that's 30 to 40 percent cheaper than the original, but it's going to last almost as long, and the original only makes sense if you have a valid warranty on your phone, or if you're going to sell it after you've repaired it.

💡

For the Redmi 8 Pro, the original glass is labeled MDY10-0076A or MDY10-0076B. Analogues should match in size: 6.53 inches, resolution 2340×1080.

Where to change glass cheaper: TOP-5 options

The choice of service depends on your budget, repair time and willingness to take risks, and we analyzed user reviews and compiled a rating of options from the most reliable to the most risky:

1. The official service of Xiaomi (Mi Service):
2. Authorized Partners (e.g., “Communication Service”):
3. Local service centers (with good reviews):
4. Private Masters (from the ads):
5. Self-sustaining replacement:

⚠️ Please note: Avoid services that are:

• 🚫 Refusing to show the spare part before installation.
• 🚫 Prepayment for diagnosis (more than 500) ₽).
• 🚫 Guarantee repair "for 1 hour" - quality glass replacement takes 2-3 hours.

Step-by-step: how to change the glass yourself

If you decide to save and replace the glass with your own hands, follow this instruction, and we warn you that the process requires care - one mistake can damage the matrix or plumes.

• 🔧 New glass (preferably with a glue base).
• 🔥 Building hair dryer (or powerful household hair dryer).
• 🧲 Suction cups for glass removal.
• 📏 Plastic mediators (or guitar mediators).
• 🧴 Clay. B-7000 or LOCA (if the glass is glue-free).
• 🔍 Loop or magnifying glass (to check plumes).

Step 1: Preparing the phone

Turn off the Redmi 8 Pro and retrieve it. SIM-card and memory card. heat the screen edge with a hair dryer (60-80 temperature)°C) for 2-3 minutes to soften the glue.Do not direct hot air to the camera or speaker!

Step 2: Removing broken glass

With suction cups, gently lift the glass, insert the mediator into the gap and slowly guide it around the perimeter, separating the glass from the body. Be careful - the sensor and display plumes pass under the glass!

Step 3. Cleaning the hull

Remove the residue of old glue from the phone and the matrix. Use alcohol or a special cleaner (for example, Isopropyl Alcohol 99%). Check the integrity of the plumes - if they are damaged, you will need to replace the display module.

Step 4: Installation of new glass

If the glass is glue-based, just put it on the matrix and press it. If there's no glue, apply a thin layer of LOCA or B-7000 to the frame, then gently glue the glass to avoid bubbles. Use the UV lamp (if there is) to polymerize the glue.

Step 5: Checking the performance

Turn on the phone and check:

• 📱 Does the sensor work (try swiping your finger across the screen).
• 🔦 Are there any color distortions (e.g., yellow spots).
• 🔊 Do the speakers work (sometimes the plume leaves when disassembling).

⚠️ Warning: If after replacement, the glass "goes away" at the edges or bubbles appear, do not try to glue it yourself - contact the service.

How much does it cost to repair different cities in Russia

Prices for glass replacement vary by region, with Moscow and St. Petersburg being more expensive to repair because of high rental rates, and regions offering better deals.

💡 Tip for residents of the regions: If your city does not have good services, consider sending your phone to Moscow or St. Petersburg through transport companies (for example, SDEC or Boxberry). Many services offer a "mail repair" service -- you send the phone, they fix it, they return it -- and it costs 500 to 800 to get it back and forth. ₽, But you will save on the repair itself.

💡

The cheapest repairs are in cities with high competition (Yekaterinburg, Novosibirsk), Moscow and St. Petersburg are overpriced by 20-30%, but it is easier to find original parts.

Frequent mistakes when replacing glass and how to avoid them

Even experienced craftsmen sometimes make mistakes that lead to additional costs, and here are the most common problems and ways to prevent them:

• 🔥 Overheating matrix: If you heat with a hair dryer for too long, you can damage OLED-It's going to burn out or it's going to turn yellow. Solution: Great it in short intervals (30 seconds) and check the temperature with your hand.
• 🧲 Train damage: If you're not taking the glass lights off, you can touch the flexible plumes of the sensor or the display. Solution: Use plastic pickers and move slowly, without jerking.
• 💧 Getting glue on the matrix: Excess glue LOCA or B-7000 It can leak under the matrix, causing stains or non-working areas. Solution: Apply the glue in a thin layer and immediately remove the excess with a napkin.
• 📱 Sensor calibration incorrect: After replacement, the glass may not respond well to touch.Solution: Reset the phone and calibrate in settings: Settings → The phone. → All parameters. → Sensor calibration.
• 🔊 Unplug the speaker: The top speaker plume may come off when disassembling. Solution: Before removing the glass, take a picture of the location of all the parts.

⚠️ Warning: If the glass starts to "go away" at the edges after 1-2 weeks, this is a sign of poor-quality glue. Do not try to reglue it yourself - the service will do this for 300-500 ₽, The risk of damage to the matrix during re-disassembly is very high.

FAQ: Answers to Frequent Questions About Glass Replacement