Xiaomi Redmi Note 10S — touchscreen AMOLED, But even it's not immune to falls, bumps, or factory defects, and if your display is no longer responsive to touch, displays ghost presses, or cracks, it's probably the touchscreen that's the problem. Replacing this part in the service center will cost 3-6 thousand rubles, but with the tools and patience you can cope yourself.
In this article, you can see the step-by-step photo manual, the tool list, the parts selection tips, and the common bugs that spoil the new module before you even install it. 10S (model M2101K7AG), So if you have a different version, you can check the compatibility by the articular!
Signs of a faulty touchscreen: when you need a replacement
Sometimes it's the firmware, the contacts oxidize, or the plume damage that's caused the module to break.
- 📱 The screen does not respond to touches in whole or in part (e.g., the top half does not work).
- 👻 «Ghostly" clicks: the smartphone opens apps, scrolls pages or enters characters.
- 🔄 Response delay: 1-2 seconds between touch and reaction.
- 🔍 Visual defects: cracks, wiring under glass, flickering when pressed.
- 🔌 It does not work only after falling or getting moisture.
If the problem occurs after the update MIUI, Try resetting the settings (Settings) → The phone. → Reset settings) or roll back to the previous firmware version. If the sensor stops working after the battery is replaced, check if you have damaged the display plume. Otherwise, you will likely need to replace the module.
⚠️ Attention: On the Redmi Note 10S touchscreen and display - a single module (OLED + Touch Panel. If only the sensor is damaged, you still have to change the entire screen!
Choice of touchscreen: original vs. analogues, articles and where to buy
For the Redmi Note 10S (M2101K7AG) Only plug-in modules are suitable 30-pin Original parts from Xiaomi are expensive (from 5 thousand rubles), but guarantee 100% compatibility. Analogs are cheaper (2-3 thousand), but may have problems with calibration or brightness:
| Type of spare part | Article/marking | Price (2026) | Pluses | Cons |
|---|---|---|---|---|
| Original (OEM) | MDY11-EG, M2101K7AG | 4 500–6 000 ₽ | Perfect color reproduction, no driver problems | Expensive, hard to find in stock |
| Analogue (A)+) | For Xiaomi M2101K7AG (logoless) | 2 500–3 500 ₽ | Cheaper than the original, often with a frame already pasted | Calibration may be required, artifacts may be |
| Copy (Copy) | No article, "under Redmi Note" 10S» | 1 500–2 000 ₽ | Lowest price ever. | Poor sensitivity, distorted colors, short service life |
Where to buy:
- 🛒 AliExpress – Cheapest, but Longest to Wait (Look for 98-rated sellers%+ and Russian reviews).
- 🏬 Local stores (for example, FixPriceService, MobiShop) – faster, but more expensive by 20-30%.
- 🔧 Service centers – sometimes sell used originals after replacement under warranty.
⚠️ Warning: Before buying, make sure that the kit is double-sided adhesive tape to fix the module. If not, buy it separately (for example, buy it separately, 3M 9448A It's called Tesa 61395, and without it, the screen will play when you press it!
💡
Before ordering, ask the seller for a photo of the module connector - it must match yours (30 contacts, the location as in the photo below).Some Chinese sellers will slip a part from the Redmi Note 10 Pro that will not fit!
Replacement tools: what you will need
For the Redmi Note disassembly 10S And you need a tool to replace the touchscreen, and you need a tool, so don't try to do with a knife or a screwdriver in a furniture kit, you're going to damage plumes or plastic latches:
- 🔧 Screwdriver kit: cross-haired PH00, flat 1.5 mm, five-pointed Y00 (back-coat).
- 📱 Plastic mediators (2-3 pieces) - for dissociating the body without scratches.
- 🔥 Dryer or thermo-air station - for softening the glue (temperature 60-80)°C).
- 🧲 Suction cup – to suction the screen after heating.
- 🔌 Tweezers to detach the plumes.
- 📏 scalpel or knife for cutting adhesive tape.
- 🧴 Isopropyl alcohol (90%+) — glue-cleaner.
Also prepare:
- 📦 Container for screws (so as not to confuse the assembly).
- 📸 Smartphone for photos – take each step, it will help with the reverse assembly.
- 🔋 Charger - after replacement, check the sensor when connected power.
☑️ Preparation of the workplace
Step-by-step: how to disassemble Redmi Note 10S replace the touchscreen
The replacement process takes 1.5-2 hours. Take your time, most breakdowns are caused by haste.
Step 1: Removing the back cover
1. Turn off the phone and remove the tray for SIM-map.
2. heat the hair dryer back cover around the perimeter (hold at a distance of 5 cm, temperature 60-70)°C. The glue will soften in 2-3 minutes.
3. Insert a plastic mediator into the gap between the lid and the housing (start at the bottom corner where the connector is) USB-C). Carefully drive the mediator along the edge, snapping the clamps.
4. Remove the cover. Be careful, it's connected to the fingerprint scanner plume!
Step 2: Shutting off the battery
1. Unscrew 10 screws that fix the metal plate (use a screwdriver). PH00).
2. Carefully remove the plate and put it aside (do not lose rubber pads!).
3. Disconnect the battery connector with a flat screwdriver. This is a must-do step -- if you don't turn off the power, you can burn the motherboard when you're working with the plumes!
Step 3: Removing the old display module
1. Heat the front of the phone (from the screen side) with a dryer for 3-5 minutes. The glue under the display should become soft.
2. Stick the suction cup to the bottom of the screen and pull it up. If the screen doesn't respond, reheat the problem areas.
3 When a gap appears, insert a plastic mediator into it and gently lead along the edge, cutting the glue. Don't push too hard, there are plumes underneath the screen!
4. Disconnect the display connector (it is under a metal frame screwed with 4 screws). Use tweezers to avoid damaging the contacts.
Step 4: Install a new touchscreen
1. Remove the protective film from the new module and make sure that there is no dust on the connector.
2. Connect the plume to the motherboard and fix it with a metal frame (twistle the screws).
3. Apply bilateral tape on the frame of the phone (if the kit was self-adhesive tape - remove the protective layer from it).
4. Carefully put the new screen in place, combining the speaker and front camera holes. Press it around the edges so that the glue grabs.
Step 5: Assembly and testing
1. Connect the battery and turn on the phone.
- 📲 Does the sensor respond to touches throughout the area.
- 🎨 Are there any color distortions or broken pixels.
- 🔊 Does the speaker and front camera work.
2. If everything works, turn off the phone, disconnect the battery and complete the assembly (set the back cover, twist the screws).
What to do if the new touchscreen does not work?
Calibration of the touch screen after replacement
Even the original module may require a sensitivity setting, and if the touches are not accurately defined after the replacement (for example, the keyboard "goes away" to the side), calibrate:
1. Open the engineering menu by entering the code:
##6484##2. Select the Touch Screen Test → Touch Screen Calibration.
3. Follow the instructions on the screen: click on the points that appear with a cross (not a finger!).
4. Upon completion, restart the phone.
If the engineering menu doesn't open, use the Touchscreen Calibration app from Google Play. Alternatively, reset (Settings) → System system → Resetting settings), but it will delete all data!
⚠️ Attention: MIUI 14+ The engineering menu can be blocked, and in this case, the calibration is done through the ADB (The command to run the test: adb shell am start -n com.android.settings/.DevelopmentSettings
💡
If you've had a problem after calibration, check if the sensor has dirt or if the plume has been damaged. Often, the touchscreen that floats is caused by the module not fitting tightly to the frame.
Common Mistakes and How to Avoid Them
Most problems when replacing the touchscreen with Redmi Note 10S It's associated with sloppy plume work or improper assembly:
- 🔌 The plume connector is damaged by pulling a wire or using metal tools. Correction: only replacing the connector on the board (expensive).
- 🔥 Overheating the board with a hairdryer - if you hold it too close. Correction: let the phone cool down 10-15 minutes before turning on.
- 🧲 Loss of screws or gaskets will cause the screen to fit loosely. 10S.
- 📏 Uneven double-sided tape sticker - the screen will "play" when pressed. Correction: re-patch module.
- 🚫 Using superglue instead of special tape - the screen will be impossible to remove without damage.
To avoid mistakes:
- 📸 Take photos of each step – especially the location of plumes and screws.
- 🕒 Don’t rush – it will take at least an hour to get to the showdown.
- 🔍 Check parts for defects before installation (e.g. microcracks on glass).
Replacement cost in service vs. self-repair
If you are not sure about your own abilities, compare the costs:
| Option | Cost (2026) | Pluses | Cons |
|---|---|---|---|
| Independently (analogue A)+) | 2 500–3 500 ₽ | 50-70% savings, experience of repair | The risk of damage to the phone, no guarantee |
| Service centre (original) | 5 000–7 000 ₽ | 3-6 months warranty, quick repairs | Expensive, possible markups for “urgent” |
| Self-directed (original) | 4 500–6 000 ₽ | Best quality, best experience | High price of spare parts, difficult to find |
It is best to buy an analogue of class A.+ If you're willing to take a risk, if you're willing to change your phone, you can contact Xiaomi's official service, or you'll lose the right to free repairs.