Extraction SIM-Xiaomi Redmi cards seem like a simple task, but in practice, users face typical mistakes, from breaking a paper clip to jamming tray.This procedure requires care, especially if you are working with hybrid slots or dual-sim models for the first time. Unlike older push-button phones, where the SIM was removed in seconds, modern Redmi have protected mechanisms that are easy to damage if you carelessly handle.
In this article, we will analyze not only the standard method of extraction, but also the nuances for different generations of Redmi (from Redmi). 4A Up to Redmi Note 12 Pro+), We'll also tell you what to do if the tray is stuck or the paper clip doesn't work. SIM-The card has a microSD, which can cause data loss, and we'll also warn you about the hidden risks, like why you can't use a pin instead of a paper clip, or how you can avoid damaging the sealing gum that protects your smartphone from dust.
Preparation: What will be needed to extract SIM-map
Before you start extracting, make sure you have everything you need. Most of the problems are caused by improvised tools, like nails, needles or toothpicks, that break inside the slot or scratch the case.
- 📎 Paperclip for extraction (goes with the phone; if lost - any unbended paperclip diameter will fit ~0.7 mm mm).
- 🔦 Flashlight (to inspect the slot for debris or damage).
- 🧴 Alcohol wipes (for cleaning contacts) SIM-cards and slots if the phone does not see the network).
- 📱 Spare. SIM-card (to check the operability of the slot after extraction).
If you have a hybrid slot model (like Redmi Note 10 Pro or Redmi). 9T), wherein two are simultaneously SIM-Prepare the container for small parts - it is easier than it seems to lose the nano-SIM. SIM-map in settings (Settings) → SIM-Maps and mobile networks: when one card is retrieved, the second card may temporarily lose communication.
Where is the slot for SIM-maps in Xiaomi Redmi
The slot's location depends on the model and year of release. In most Redmi, it is on the left side of the slot (when you look at the screen), but there are exceptions:
- 📱 Redmi 4/5/6 series, Redmi Note 5/6/7: slot on the right side (near the switch button).
- 📱 Redmi 7A/8A/9A: slot on the top edge (a rare solution, often causing confusion).
- 📱 Redmi Note 8 Pro and newer: The slot returns to the left side, but can be shifted closer to the bottom corner.
To determine the exact location, inspect the case: look for a small hole with a metal rim (diameter). ~Some models have a pictogram next to them. SIM-If you are not sure, check the specifications of your model on the official Xiaomi website or in the documentation.
💡
If the slot is located on the upper edge (as in Redmi). 9A), Remove the tray over a soft surface (for example, over the bed) – so you will not lose SIM-fall-card.
Step-by-step instructions: how to remove SIM-map from Xiaomi Redmi
Follow this algorithm to avoid damage. If something goes wrong at some point (like the tray doesn't come out), don't force it -- go to the "What to do if the slot is stuck" section.
- Turn off the phone. This is not necessary, but it is recommended: this will eliminate the risk of short circuits when accidentally touching contacts.
- Put the paper clip in the hole to the point. You should hear a slight click, which means that the tray locker has snapped.
- Carefully pull the tray over you. Don't pull at an angle! The movement should be smooth and straight.
- Extract. SIM-If you have a hybrid slot, remember the order of the card installation (usually nano-SIM on top, microSD on bottom).
☑️ Pre-extraction check
On retractable models (e.g. Redmi K50 Gaming), the tray may not come out completely - it needs to be tucked with a nail or a plastic card.
| Xiaomi Redmi Model | Slot type | Features of extraction |
|---|---|---|
| Redmi Note 11 Pro+ | Hybrid (2 nano-SIM + microSD) | The tray goes 2/3 length - pull to the end |
| Redmi 10C | Single slots (2 nano-SIM + microSD) | SIM-cards are fixed with a latch - press on the edge to extract |
| Redmi 9T | Hybrid | When removing the microSD, hold the tray – it can pop out completely |
| Redmi 8 | Hybrid | The hole for the paper clip is deeper than usual - insert the tool to the point |
What to do if the tray SIM-sticker
If the tray doesn't come out after you press it, don't panic. The reasons can be from dust to factory defects.
- Check the paperclip: it should be flat and of sufficient length. If the tip is bent, straighten it or take another.
- Press harder, but not fanatically, and sometimes the mechanism sticks to the moisture or oxidation.
- Try alternative methods: 🧲 Use a magnet (like a speaker): bring it to the slot - sometimes it helps move the tray. 💨 Blow the hole with compressed air (a canister for cleaning equipment) - this will remove dust. 🔧 Carefully swing the paperclip left-right inside the hole to stir the locker.
Contact the service.
What NOT to do if the tray is stuck
⚠️ Warning: If the tray is halfway out but doesn't go any further, don't pull it with pliers! Part of the hold may remain inside, and then you'll need a complete module replacement. SIM-Cards (cost - from 1500 rubles in service centers).
How do you put it in? SIM-Map back: nuances for different models
Installation SIM-The card back seems easier than the extraction, but there are pitfalls here: SIM-The map should be downward, and the bevelled angle should be the same as the tray, so if you mix the sides, the phone won't see the network, and if you force the insert, you can bend the contacts.
For models with a hybrid slot (Redmi Note 10, Redmi 9), consider the following points:
- 📶 First first SIM-card 1) usually 4G/5G, second (slot) 2) — only 2G/3G. Check in the settings (Settings) → SIM-map → Preferred network).
- 💾 If you use a microSD, install it in the bottom slot (on most models). SIM-The card won't work.
- 🔄 Once installed, reboot your phone – this will speed up card initialization.
On the Redmi K40 and Redmi K50, the tray has a two-tiered design: the upper level is for nano-SIM, the lower level is for microSD. If the card is not fixed, check if it is mounted “upside down.” Also avoid using micro-SIM adapters: they often do not fix in the tray and can fall out when vibrating.
(1) Correct installation (contacts must be clean).
2) APN settings (automatically loaded but sometimes confused).
3) Slot condition - if contacts are damaged, repairs will be required.-->
Frequent Mistakes and How to Avoid Them
Even experienced users make mistakes when working with the SIM-Here are the most common ones and how to prevent them:
- 🚫 Using inappropriate tools: needles, toothpicks or nails scratch the body and break inside. Use only a paper clip or a special key from the kit.
- 🚫 Excessive force: If the tray does not come out, do not push hard - this is how you can break the lock. It is better to try again in 10 minutes (sometimes the mechanism "thaws" after heating the phone in your hands).
- 🚫 Installation SIM-cards without turning off your phone: in rare cases, this can cause the communication module to fail.Always restart the device after tray manipulation.
- 🚫 Ignoring sealing gum: on models with protection IP53 (For example, Redmi Note 11S) There's a rubber seal on the perimeter of the tray, and if you damage it, the phone will lose its dust protection.
Another common problem is loss. PIN-post-reshuffle SIM-If the phone asked for it. PIN, But you don't remember it, you don't enter it at random: after 3 wrong attempts, the card will be blocked. In this case, contact the operator with the passport for unlocking (service is paid, cost is not required — ~200 rubles).
⚠️ Attention: On some firmware MIUI (especially on Redmi for the Chinese market after extraction SIM-If you used a phone with a linked account, check before retrieving the card whether you remember the username and password, otherwise you risk losing access to the phone!
Alternative methods of extraction SIM-cards (if there is no paper clip)
If you don't have a paper clip, you can use the tools you can use, but with caution.
- 🖊️ The gel pen rod: Remove the rod, heat it with a lighter to melt the plastic, and form a hook. Cool it and use it as a clip.
- 📎 Hair clip: straighten it and cut a piece of length ~3 cm Scarve the end with a file so that it enters the hole.
- 💳 Edge of plastic card: if the tray is slightly extended, put it under the card (for example, discount or bank card!
- 🧲 Magnetic phone holder: If you attach it to the back next to the slot, sometimes the tray is shifted by the magnetic field.
If you are on a trip and need to get out urgently SIM-If you have a card, you can contact the communication salon (for example, MTS or Beeline) - they usually have tools for such cases. In extreme cases, use the services of workshops, but check the cost in advance: in Moscow services, the price for removing the tray varies from 300 to 800 rubles.
💡
If you travel frequently, buy a metal key for your travels. SIM-card (worth) ~100 rubles on AliExpress. It's smaller than a paper clip and doesn't bend.