How to get out SIM-Xiaomi Redmi 6: 3 Proven Ways + frequent

Replacement SIM-The card or its extraction for transfer to another device is a routine operation that can turn into a headache if you do not know the nuances of the Xiaomi Redmi 6 design. This model, released in 2018, is still popular due to the balance of price and functionality, but its hybrid tray (support 2 Nano-SIM) + microSD) is a frequent question for users, and unlike flagships with retractable mechanisms, it's simpler -- but the risk of damaging contacts with careless extraction is higher.

Many owners face problems: the tray does not come out the first time, the SIM gets stuck inside, or after extraction, the network ceases to be defined. SIM-The card (including the emergency version without a paper clip), analyze common errors and give recommendations for the care of the slot, and if you plan to replace the SIM with a new one, there is a checklist at the end to check compatibility.

Redmi 6 supports Nano-SIM (4FF) It doesn't work with other formats without an adapter, and if you have an old-style SIM (Mini-SIM or Micro-SIM), you'll have to cut it off or replace it in the carrier's cabin. SIM-The second slot blocks the possibility of installing microSD – this is a feature of the hybrid design.

1.Preparation: What will be required to extract SIM-map

Before you start the procedure, make sure you have everything you need. Unlike today's magnetic tray smartphones, the Redmi 6 requires mechanical action — and accuracy is important.

The main tool is a paper clip for extraction SIM-If you don't have one, alternatives will work:

• 📎 Office paper clip (unbended, with a diameter not thicker than 0.7 mm)
• 🔧 Needle or pin (only with blunt end so as not to scratch the body)
• 📱 Special key from the sets for repairing phones
• 🔨 Toothpicking (if nothing else, but the risk of breaking it is high)

⚠️ Note: Do not use sharp objects (knives, scissors, sewers) – they can damage the tray O-ring or contacts inside the phone. Also avoid metal objects with magnetic properties (for example, a screwdriver) so as not to disrupt the compass or the contact. NFC-Module (if you have it in your Redmi 6 version).

In addition to the tool, prepare:

• 🔦 Good lighting (better to use a desk lamp or flashlight)
• 🧻 Soft cloth or napkin (to put the phone down and not scratch the screen)
• 🔍 Lupu (optional, if the hole for the paper clip is poorly visible)

If you extract SIM-Transfer card to another phone, check in advance:

1. Does the new device support the same format (Nano-SIM)?
2. Is the service "Mobile Internet" activated - when changing the SIM card, it can turn off.
3. Are contacts retained on SIM-card (if yes, export it to your phone's memory).

Method 1: Standard extraction by means of a paper clip

This is the main and safest method recommended by the manufacturer, and it is suitable for 90% of cases, if the tray is not damaged or jammed.

Step 1: Turn off the phone (optional, but recommended for safety) If the battery is removable (in some Redmi 6 versions), you can remove it, but you don't have to.

Step 2: Find a hole to remove the tray, which is located on the right end of the phone (if you look at the screen), and in some versions of the case, the hole can be covered with a plug, you need to carefully tuck it with your nail.

Step 3: Put the paperclip into the hole at a 45-degree angle and press until you click. The tray should extend 1-2 mm, after which it can be pulled out with your fingers.

Check that the phone is on a flat surface.

Make sure the paper clip enters the hole without backlash

Press the paperclip smoothly, without jerking

Do not use force if the tray does not yield.-->

⚠️ Attention: If the tray does not come out after 2-3 attempts, do not push harder, it can break the mechanism. Try to slightly sway the paperclip left-right or change the angle of pressing. In extreme cases, move to method 3.

When the tray is out, carefully take it out and remove it. SIM-Notice the markings inside the tray:

• SIM 1 - the main slot (supports) 4G)
• SIM 2/microSD – Hybrid slot (works with either the second slot) SIM, or with a memory card)

If you plan to insert the tray back, make sure that:

• 📱 SIM-card inserted by contacts down (the golden side should be facing the back cover of the phone).
• 🔄 The tray is inserted to the point - if it is not fixed, check whether dust or contamination interferes with it.

💡

If the tray is tightly reentered, do not force it. Try blowing the hole with compressed air (such as a can of keyboard cleaning) - often the problem is the accumulated dust.

Method 2: Extract without paper clips (alternative methods)

If you don't have a paper clip on hand or it's broken, you can do with the tools at hand, the main thing is not to use objects that can damage the case or internal contacts.

Option 1: Toothpick or plastic card

1. Take a toothpick and break its tip to make a sharp, but not prickly edge.
2. Put it in the hole for the paper clip and press, while pulling the tray on yourself.
3. If the toothpick bends, wrap its tip with foil for stiffness.

Option 2: Tape or scotch

• 🎀 Stick a piece of tape to the edge of the tray (if it protrudes a little bit).
• 🖲️ Pull the ribbon smoothly, without jerking.
• ⚠️ Do not use superglue or double-sided scotch – they can leave marks on the case.

Option 3: Vacuum method (for experienced)

1. Apply a small vacuum pump to the tray (for example, from a phone holder in the car).
2. Pull on yourself while pressing the hole for the paperclip.
3. ⚠️ Risky method - you can tear the tray from the guides.

⚠️ Note: If the tray is jammed due to moisture or corrosion, do not try to pull it out by force.In this case, it is better to contact the service center - independent actions can damage the contact group or break the antenna cable.

Method 3: Emergency extraction in a wedged tray

If the tray does not come out of any of these ways, you will have to resort to radical measures, which requires accuracy and is only suitable in extreme cases.

Step 1 - Disassemble the back cover

• 🛠️ Remove the back of the phone. In Redmi 6, it's mounted on the latches -- put a plastic spatula on it).
• 🔋 Disconnect the battery (if it is removable) or turn off the battery plume (in non-removable versions).

Step 2. Access to the tray

• 🔍 Find the tray mechanism – it is located next to the antenna contacts.
• 🖲️ Carefully tuck the tray on the inside with a screwdriver or tweezers.

Step 3: Inspection and assembly

• 🧹 Clean the tray and phone contacts of dust (use a brush or compressed air).
• 🔧 Make sure the spring mechanism is not deformed.
• 📱 Collect the phone in reverse order, check the work SIM-map.

⚠️ Warning: Disassembling your phone is warranty-free (if it's still valid) and can damage the plumes. If you're not sure about your skills, you'd better contact the service. Also remember that some Redmi 6 versions have a non-removable battery, which requires experience to turn off.

5. Common Mistakes and How to Avoid Them

Even with this simple procedure, users often make mistakes that lead to breakdowns, and here are the most common ones and ways to prevent them:

Mistake 1: Using the wrong tools

Many people try to open the tray with a knife, scissors or even keys, which leads to:

• 🔧 Scratches on the body around the hole.
• 💥 Breakdown of the spring mechanism inside.
• ⚡ Close contacts (if the tool is metal and gets on the board).

Solution: Use only plastic or wooden items (dental cleaning, shoulder blade).

Mistake 2: Excessive force application

If the tray doesn't come out the first time, you don't have to push it hard.

• 🔨 Bend the guides inside the phone.
• 📵 Damage antenna contacts (located near the slot).
• 🔋 Remove the battery plume (in non-removable versions).

Solution: Try swaying the paperclip left-right or slightly heat the body with a hairdryer (temperature not higher than 50).°C to expand the plastic.

Error 3: Incorrect installation SIM-map

A common problem is that the SIM is inserted "upside down" or not completely.

• 📶 Lack of network (the phone does not see the SIM).
• 🔋 Fast battery discharge (phone constantly looking for network).
• 💥 Overheating of the communication module (due to short circuit of contacts).

Solution: Always make sure that the bevelled angle of the SIM coincides with the angle on the tray.

1. correct installation of the SIM (contacts should be at the bottom).

2. the purity of contacts (wipe them with a stripe or alcohol).

3. the SIM's performance on another phone.

If the problem persists, it may have been damaged. SIM-motherboard controller.-->

6. Care for SIM-The snail: how to extend his life

To avoid problems with extraction SIM-Maps in the future, follow simple recommendations:

1. Regular cleaning

• 🧹 Once every 3-6 months, blow the hole for the paper clip with compressed air.
• 🧴 Wipe the contacts of the tray and simki with isopropyl alcohol (at least 90%).
• ❌ Do not use wet wipes or water – this causes corrosion.

2. Proper storage

• 📦 If the phone is not used for a long time, take it out. SIM-Keep the card in an antistatic bag.
• 🌡️ Avoid storing your phone in wet or dusty places (such as a bathroom or garage).

3. Careful treatment

• 🖲️ Do not press the tray with your fingers - only through the clip hole.
• 🔋 Do not remove the SIM when the phone is on (although Redmi 6 supports hot replacement, this increases the risk of crashing).
• 📵 Do not drop the phone with the tray removed - this can damage contacts.

⚠️ Note: If you change frequently SIM-Cards (e.g. using your phone for testing), consider buying an external adapter SIM-It connects via USB-Type C and avoids mechanical wear on the internal slot.

Frequent questions about SIM-Maps in Xiaomi Redmi 6