How to remove and clean garbage from the robot vacuum cleaner Xiaomi: detailed instructions with a photo

Why it’s important to clean the garbage container in Xiaomi’s robot vacuum cleaners correctly

Xiaomi's vacuum cleaners - from the budget Mi Robot Vacuum-Mop to the flagship DreameBot - require regular dust bag care. The accumulation of debris not only reduces the efficiency of cleaning, but can also lead to turbine failure, engine overheating or sensor lockdown. For example, in models with wet cleaning function (Viomi) V3, Xiaomi S10+) A packed container often causes an error. 02-0303 ("water pump problem), although the real problem is clogging of the air channel.

The manufacturer recommends cleaning the dust collector after each cleaning cycle, but in practice users often forget to do this, as a result, not only dust accumulates inside, but also hair, animal hair, small construction debris (if the robot cleans after repair). It is especially dangerous to ignore cleaning in models with HEPA-Filters (e.g. Xiaomi Mi Robot Vacuum-Mop) 2 Pro: A clogged filter reduces the suction force on 40-60%, and it costs to replace it. 1/3 cost of new vacuum cleaner.

This article provides step-by-step instructions for all popular Xiaomi models, including design nuances, deep cleaning methods, and answers to frequent questions. If your robot vacuum cleaner starts to buzz louder than usual, suck garbage or make mistakes, it’s likely that the problem is with the dust collector.

Preparation for cleaning: what will be needed

Before you start removing garbage, prepare the necessary tools and place to work, which will speed up the process and help avoid common mistakes (for example, loss of small parts or damage to seals).

• 🧹 Soft brush (old tooth or makeup brush is suitable) - to clean hard-to-reach places.
• 🧴 Soap solution (warm water) + dishware) or a specialized cleaner for vacuum cleaners.
• 🧻 Microfiber wipe or paper towels - for drying parts.
• 🔧 Flat screwdriver (for models with screw container mounts, for example, Dreame) D9).
• 😷 Respirator or mask – if you are allergic or clean the dust collector after general cleaning.

Also check in advance if the robot is on the error indicator. If so, take a photo of the code (for example, take a photo of the code, 05-0102) and check the section. FAQ At the end of the article, some mistakes 01-0301 Viomi SE) indicate clogging of the duct, and cleaning the container will not eliminate them - you will need disassembly of the body.

⚠️ Warning: Never use abrasive sponges, metal brushes or aggressive detergents (such as Domestos) to clean the dust collector. They damage the antistatic coating of the container and sealing gums, resulting in loss of tightness and dust entering the engine.

How to remove a garbage container: a universal instruction

Most Xiaomi robot vacuum cleaners have similar dust collector designs, but there are nuances depending on the model. Below is a general algorithm that is suitable for 90% of the brand’s devices, including the Mi Robot Vacuum, Viomi and Dreame.

1. Turn off the robot and disconnect it from the charging station if the model supports a removable battery (e.g. DreameBot). L10 Pro, it is better to remove it – this will prevent accidental switching on during cleaning.
2. Turn the vacuum cleaner upside down. On most models, the container is located in the center of the case, under the top panel. Except for Xiaomi Mi Robot Vacuum-Mop 2 Lite, where the dust collector is hidden under the back cover.
3. Find a latch or button (usually marked with an icon) 🗑️). Click on it and pull the container over you. In some models (like the Viomi). V2 Pro) first move the lid to the right and then lift it up.
4. Remove the container completely. If it doesn't respond, don't force it, make sure the latches are caught. In dual-container models (dry and wet cleaning), the dust collector is pulled out first, then the water tank.

At this point, many users make the mistake of trying to shake out the garbage directly above the bin without separating the container lid, leaving the dust scattered around the room, leaving small particles (hair, thread) inside.

Step-by-step cleaning of the container: from garbage to filter

Now that the container is removed, we start cleaning it up, and there are several steps that you should not skip, because even if the dust collector looks clean, there may be particles inside that will eventually break down.

1. Disposal of large debris

Open the container lid (usually with a latch or a magnet) and shake the garbage out of the trash can, then:

• 🧹 Use a soft brush to remove dust from the inner walls and corners.
• 🎯 Notice the duct hole (usually located at the top of the container) and the clogging of this hole is the main cause of the error. 01-0301 ("suction-power").
• 🧲 For hair removal and hair, use a sticky roller or tweezers. D9) hair is often wound on the shaft - they need to be carefully cut with scissors.

2.Washing the container

The container can be washed only with warm water (temperature not higher than 40).°C) Hot water deforms plastic, cold water does not dissolve fatty deposits:

1. Soak the container in soapy solution on 10-15 minute.
2. Clean all the holes and channels with a soft brush.
3. Wash thoroughly under running water, making sure there is no detergent left in the depressions.

3. Cleaning the filter

The filter (usually located on the side or top of the container) is the most vulnerable element. HEPA-filters (Xiaomi) S10, Viomi V3) it can not be washed - only blow back airflow (for example, a dryer in the cold blow mode) or replace each 3-6 For regular filters:

• 🚿 Wash under a stream of water without using detergents.
• 🌬️ Dry in the air for at least 24 hours. Do not dry with a hair dryer or on a battery - this violates the structure of the filter.

After cleaning all the elements, leave the container and filter to dry on 1-2 You can't put them back in the wet state, which will short-circuit or corrosion the contacts (relevant for models with electronic filling sensors, such as DreameBot). Z10 Pro).

💡

If the container has a persistent odor, put a bag of baking soda or activated carbon inside for 30 minutes, which will help neutralize the odors without using chemistry.

Features of cleaning for popular Xiaomi models

While the principle of container cleaning is the same for most robot vacuum cleaners, some Xiaomi models have unique design features. Below is a table with nuances for the most common devices.

If your model is not in the table, pay attention to the type of filter and the presence of additional sensors, for example, in robots with the function of Carpet Boost (DreameBot). L10 Pro) the container is heavily sealed - it cannot be washed in the dishwasher, only by hand.

Cleaning the duct and turbines: when standard procedure is not enough

If after cleaning the container, the robot still works worse - it does not suck up garbage, makes whistling sounds or makes an error 01-0301 — The problem may be clogging the duct or the turbine, which is a more complex procedure, but you can do it yourself.

1. Cleaning of the duct

The duct is the channel connecting the container to the turbine, and in Xiaomi models, it often gets clogged in two places:

• 🔄 Entrance hole (under the container) – dust and small debris accumulates.
• 🌀 Bending of the tube (closer to the turbine) - hair and threads are wound.

Use a flexible brush brush (you can make it out of wire and cotton wool) or a vacuum cleaner with a narrow nozzle. V3 DreameBot is removable - it can be washed under water.

2. Turbine cleaning

The turbine is the heart of the vacuum cleaner, and the clogging causes the power to be lost and overheated, and to get to it,

1. Remove the container and the filter.
2. Unscrew the screws on the bottom cover (usually them). 4-6).
3. Carefully tuck the lid with a plastic spatula (do not use metal tools!).
4. Remove debris from the turbine blades with a soft brush or compressed air (a canister for cleaning equipment).

⚠️ Warning: When disassembling a turbine, do not touch its blades with your hands - they are sharp and can cut. Also do not use wet wipes for cleaning: moisture on bearings leads to corrosion and failure of the turbine (the cost of replacing is up to 70% of the price of a new vacuum cleaner).

After cleaning, assemble the robot in reverse order. If you turn on an unusual noise (screaming, vibration), then the turbine is installed incorrectly - disassemble the vacuum cleaner and check the fixation of the blades.

💡

If the robot is still not sucking well after cleaning the turbine, check the container's sealing gum. Over time, it loses its elasticity, and the tightness is broken. 5-10 less expensive than a turbine repair.

How to prolong the life of the container: tips for care

Regular cleaning is only half the success, so to make the container last longer and the robot vacuum cleaner work more efficiently, follow these guidelines:

• 📅 Keep a cleaning schedule, for example, after each 3rd cleaning, wash the container with soap, and once a month, clean the duct.
• 🚫 Avoid heavy debris. Construction dust, sand, large nuts or coins can damage the turbine. Use special nozzles or a cyclone filter vacuum cleaner to clean up after repair.
• 🔄 Alternate filters. If you have a spare one. HEPA-filter, change them once 2-3 month, and the one used - wash and dry for the next cycle.
• 🌡️ Store the container correctly. After cleaning, leave it to dry in a ventilated place, but not in direct sunlight (UV-radiation).
• 🛒 Use original consumables. Non-original filters and seals often do not provide leakage, which leads to dust entering the engine.

For models with automatic emptying station (Xiaomi) S10+, DreameBot X30) additionally:

• 🗑️ Change the dust bag at the station every time. 1-2 month (depending on the intensity of cleaning).
• 🌀 Once every 3 months, clean the station inlet from accumulated dust (use a vacuum cleaner or a can of compressed air).

Compliance with these rules will help to avoid 90% For example, in Xiaomi service centers, the most common reason for complaints is the failure of the turbine due to hair getting into bearings. Regular prevention allows you to save on repairs before the end of the day. 10-15 thousand rubles a year.

FAQ: Frequent questions about cleaning Xiaomi container