How to install an adapter on Xiaomi: instructions for all types of devices

Installing an adapter on Xiaomi devices is a challenge faced by both beginners and experienced users. Według statistics of service centres, before 15% calls are associated with incorrect installation of communication modules (Wi-Fi, Bluetooth) or physical damage to connectors when connecting OTG/USB-This article will help you avoid typical errors and perform the procedure yourself, from choosing a compatible adapter to testing its operation.

We will look at all the current scenarios: from a simple installation USB-OTG adapter for connecting flash drives before replacing the internal Wi-Fi/Bluetooth module on smartphones Redmi Note 12, POCO X5 or Mi 11. Particular attention will be paid to models with non-standard connectors (for example, Xiaomi). 13 Ultra with port USB-C 3.2 Gen2) All instructions are updated to the firmware. MIUI 14/15 hyperos 2026 year-end.

1. Which adapters are compatible with Xiaomi: a complete list of types

Before you start installing, it’s important to determine which adapter your device needs. Xiaomi has a few key categories:

• 📶 External Wi-Fi/Bluetooth Adapters for PCs and routers (e.g. Xiaomi Wi-Fi) 6 AX3000). Connect through USB-A or USB-C.
• 🔌 OTG-Adapters – allow you to connect flash drives, keyboards or mice to smartphones (compatible with most Android 10 models)+).
• 📱 Internal communication modules to replace broken Wi-Fi/Bluetooth chip (requires disassembly of the device).
• 📡 Adapters for SIM-cards – adapters between nano-SIM, micro-SIM and eSIM (relevant to Xiaomi 14 and newer).
• 🖥️ HDMI/DisplayPort adapters - to display the image on the monitor (work only on flagships with support) USB-C Alt Mode).

It's critical to check the version of the protocol, like an adapter. USB 2.0 will not be able to provide the data rate declared for the port USB 3.2 on Xiaomi Pad 6. and Wi-Fi 5 module will not reveal the potential of the Wi-Fi router 6E.

2.Preparation of the device: what to do before installation

Regardless of the type of adapter, preparing the device will reduce the risk of errors.

Backup of data (especially if disassembly is required)

Check the version. MIUI/HyperOS In Settings → The phone.

Disconnect the device from the network (for internal modules)

Prepare tools: plastic blades, tweezers, screwdriver T3/T5

Download the driver (if the adapter requires software, for example, for Xiaomi) USB-C to Ethernet)

-->

For internal work (replacement of Wi-Fi module) be sure to discharge the battery to 25-30%. This minimizes the risk of short circuits in accidental contact with the board. POCO F5 or Redmi K60, note that their batteries are soldered - you will need a needle to detach the plume.

⚠️ Attention: On devices with IP53 (for example, Xiaomi 13T) When disassembled, you lose dust protection, and if you don't plan on replacing the gaskets, avoid using adapters that require opening the body.

For external adapters (OTG, HDMI) enough:

1. Update the firmware to the latest version (in Settings) → Renewal centre).
2. Enable the Developer Mode and Activate Debugging by USB (Path: Settings → The phone. → Version. MIUI → 7 times to tap).
3. Check compatibility on the Xiaomi Support website (enter the device model).

Installation OTG-Adapter: connect flash drives and peripherals

OTG (On-The-Go is the easiest type of adapter for Xiaomi. USB-devices (flash drives, hard drives, keyboards) to your smartphone. Here's how to do it right:

1. Buy an adapter with a connector USB-C (For modern models, or Micro-USB (for older models, for example, Redmi). 4X). Pay attention to the protocol support:

• 🔹 USB 2.0 – speeds up to 480 Mbps (suitable for flash drives).
• 🔹 USB 3.2 - up to 10 Gbit / s (necessary for external SSD, For example, on the Xiaomi Pad 6 Pro).

2. Connect the adapter to the smartphone. the notification will appear on the screen "USB-The device is connected. tap it and select "Use as" USB-accumulator".

3. to work with the keyboard or mouse may require the installation of additional software (for example, USB Keyboard Helper from Google Play).

💡

If the smartphone does not see OTG-device, try disabling Battery Optimization for the application Files in the application settings.

⚠️ Attention: On devices with MIUI 14+ plug-in OTG-A storage device over 32 GB may need to be formatted into FAT32 exFAT. NTFS Not supported without root rights.

4. Replacement of internal Wi-Fi/Bluetooth module: step-by-step guide

If your Xiaomi has stopped catching Wi-Fi or Bluetooth, the problem may be the hardware module. Replacing it is a more complex procedure that requires disassembling the device.+:

Tools required:

• 🔧 Screwdriver. T3 and T5 (magnetic).
• 🧲 Plastic blades for opening the body.
• 🔥 Hair dryer or a station for heating the glue (if the battery is glue-on).
• 🛠️ Tweezers and antistatic bracelet.

Step-by-step:

1. Turn off the phone and remove it. SIM-map.
2. Heat the back cover with a hair dryer (temperature) ~60°C) and gently apply a plastic blade to it, starting at the corner near the charging socket.
3. Unscrew 12 screws that fix the metal plate (remember the location - they are of different lengths!).
4. Disconnect the battery plume (use a plastic blade to avoid damaging the contacts).
5. Find it. Wi-Fi/Bluetooth module – it is located near the top of the board (usually marked as WCN6750 or WCN6855).
6. Carefully solder the module soldering station (temperature) ~350°C) or use a thermo-air station.
7. Install a new module, fix it and assemble the device in reverse order.

On Xiaomi models 12S Ultra and newer Wi-Fi/Bluetooth The module is integrated into the main chipset (Snapdragon). 8+ Gen1). Replacing it requires soldering the entire processor – it is impractical and worth it. ~70% from the price of a new phone.

Installation of the adapter SIM-maps: nano, micro and eSIM

With the transition to nano-SIM and eSIM, many users are faced with the need to use adapters.

For the physical SIM-map:

• 📱 If you have a micro-SIM and the slot is designed for nano-SIM (like in Xiaomi 13), use an adapter cutter or order a new one. SIM operator.
• 🔄 For the reverse situation (insert nano-SIM into the micro-SIM slot) buy a plastic adapter (worth it). ~50 rubles).

For eSIM:

Xiaomi models 12T Pro, Xiaomi 13 and newer support eSIM:

1. Go to Settings. → SIM-maps and mobile networks → Add a mobile fare.
2. Select "Use eSIM" and scan. QR-operator.
3. If QR-No code, enter the data manually (options) SM-DP+ Address and Activation Code is provided by the operator).

💡

The eSIM cannot be physically removed – it is tied to the IMEI When the phone is reset to factory settings, the eSIM remains active, but may need to be re-activated by the operator.

Important: Some carriers (such as Tele2) do not support eSIM on Xiaomi.

6. Connection HDMI/DisplayPort adapter: displaying the image on the monitor

Xiaomi flagship models (such as Xiaomi 13 Ultra or Black Shark 5 Pro) support the display of the image on the external screen through the USB-C. This requires an adapter that supports DisplayPort Alt Mode.

Requirements:

• 🖥️ The adapter must support DP 1.4. HDMI 2.1 (for permissions above) 1080p).
• 📺 Monitor/television with connector HDMI/DisplayPort prior 4K@60Hz.
• 🔋 Charger of at least a capacity 30W (Adapter consumes a lot of energy).

Instructions:

1. Connect the adapter to the USB-C port of the phone.
2. Connect the adapter to the monitor cable HDMI/DisplayPort.
3. The phone will have a notification saying "External Display Connected" and tap it and select the display mode: 🔹 "Duplicate screen" - the same image on the phone and monitor. 🔹 "Expand the screen – the monitor becomes the second desktop.

Settings → Display. → External screen resolution

⚠️ Attention: POCO F4 GT and Black Shark, when connected to the monitor, can turn off charging via the same port. Use a powered hub (e.g. Xiaomi) USB-C Hub) to charge the phone and display the image at the same time.

7 Problem Solving: The adapter is not working

If the adapter does not function after installation, use this diagnostic manual:

To diagnose hardware problems (for example, after replacing the Wi-Fi module), use the following engineering menu:

Enter the phone app: ##4636##


Go to Phone Information and check the Wi-Fi/Bluetooth status.

If the adapter is defined by the system but does not work, try:

• 🔄 Reset the device.
• 🔧 Reset network settings (Settings) → SIM-maps and networks → Resetting Wi-Fi, Mobile Network and Bluetooth).
• 📥 Update the firmware through Settings → Renewal centre.

FAQ: Frequent questions about Xiaomi adapters