How to disassemble Xiaomi Mi A2 Lite: the complete guide

Disassembling the Xiaomi Mi A2 Lite is a challenging task, requiring care, patience and a specialized tool. The device has a monoblock design, where the display and back cover are glued to the frame, which makes it much more difficult to access the internal components. Unlike budget models with a removable rear panel, here the dismantling begins with the careful removal of the glass cover, which is the most risky step of the entire process.

Owners often face the need for repairs after falls or moisture when you need to replace broken glass, battery or charging plume. Understanding the internal architecture of the gadget allows you not only to save on the services of the service center, but also to be confident in the quality of the work performed. However, it is worth remembering that any intervention in the design will void the warranty if it has not expired.

Before any manipulations begin, it is critical to turn off the device and prepare the workplace with good lighting. Unprofessional disassembly can damage the plumes or the display itself, which in this model changes only with the frame. In this article, we will take a detailed look at each stage of dismantling to minimize the risks and successfully perform the restoration of your smartphone.

Preparation of the workplace and tools

A high-quality disassembly is impossible without a suitable set of tools that should be at hand before work begins. You will need a heating element (dryer or heater), mediators or thin plastic cards, a suction cup, a set of screwdrivers (usually cross P2/P5) and tweezers. The use of metal tools to open the case is highly undesirable, as they can damage the internal elements or the battery.

Special attention should be paid to the cleanness of the working surface so that small screws do not get lost and dust does not get inside the device. It is recommended to use a magnetic mat or special organizers to sort the fasteners by dismantling stages. The tools should be serviceable, and the screwdriver blades should not have barbs, so as not to break the thread in the plastic racks.

💡

Use a magnetic substrate to sort the screws: put them in the same order in which you twisted them, so that you do not confuse the length of the fastener when you assemble.

It is important to make sure in advance that all devices are serviceable, since finding the right screwdriver during operation can lead to careless movements. To work with adhesive compounds, an isopropyl alcohol or a special solvent is needed that softens the adhesive, allowing the body to open without damage.

Safety and preparatory measures

The first and most important step before disassembling the Xiaomi Mi A2 Lite is to completely shut down the power, which requires turning off the smartphone and waiting for the screen to completely shut down. Ignoring this rule can lead to a short circuit on the board if you accidentally hit the connectors or damage the insulation of the plumes when removing components.

⚠️ Warning: Never try to disconnect the battery plume while it is connected to the motherboard.This can cause a voltage surge and the power controller to fail.

SIM cards and memory cards must also be removed before the housing starts heating. SIM-The cards in this model are combined with a microSD tray, and its presence can interfere with access to some screws or simply damage when heated. Make sure that the device does not have protective glasses or cases that can melt or prevent the fixation of the smartphone.

You should work in a well-ventilated environment, because when the glue is heated, you can get unpleasant odors, and safety glasses will not be superfluous, especially if there is a risk of falling off the glass fragments when you dismantle the broken back cover. Eye and airway safety is the number one priority when working with broken glass.

Rear cover removal and primary access

The most difficult step is to separate the back glass panel from the metal body, and to do this, you need to evenly warm the perimeter of the device with a hairdryer to a temperature of about 80-90 degrees Celsius, you need to warm up carefully, not lingering long at one point, so as not to overheat the display matrix or battery. You can check the readiness of the glue by trying to gently slip a suction cup or mediator into the joint.

After warming up, a small gap is made in the lower corner of the case (usually near the charging socket) with a suction cup and a mediator. Then, without removing the tool, you need to guide it along the faces, gradually cutting through the adhesive layer. The movements should be sliding, parallel to the plane of the screen, so as not to damage the internal plumes that can pass close to the edges.

When the perimeter is passed, the back cover is removed completely, and underneath it you'll see a plastic safety panel covering most of the components, and this panel can also be glued or held on screws, so removing it requires care. The glue at this point must already be softened, but the rush can cause the plastic latches to break.

Removal of the protective panel and disconnection of plumes

And underneath the back, there's a large plastic plate that protects the motherboard, the battery and other components from dust and mechanical stress, and it's mounted with a lot of screws around the perimeter and in the center, and you have to twist all the screws counterclockwise, and you have to fold them into a separate cell of the organizer, because they can vary in length and threading.

Once the screws are removed, the panel is gently raised, and underneath it is the main plume connecting the lower board to the motherboard, as well as the display and touchscreen plumes, the first thing you need to do is turn off the battery connector to turn off the device completely, and then you can disconnect the other plumes by putting a plastic blade or nail on them.

Note the condition of the connectors: they can be contaminated or oxidized, especially if the phone got moisture. When removing the protective panel, it is important not to damage the main camera module, which often protrudes above the level of the board and can be affected by plastic. Carefully put the removed panel in a safe place.

Replacement of the battery and work with the fee

In the Xiaomi Mi A2 Lite model, the battery is glued to the display frame, which makes it difficult to replace it. To remove the old battery, you need to warm up the device again (without the back cover already) or use special hoods with suction cups. You can not pull behind the battery by force - this can lead to its damage and fire.

If you're planning to replace the motherboard, you're going to have to turn off all the plumes, and you're going to have to roll the screws that lock the board to the frame, and you're going to be able to pick up the board carefully, you can use tweezers to help you free the connectors if they're stuck, and you're going to want to check the multimeter for voltage before you install it.

When installing a new battery, make sure that the adhesive base is fresh and sticky. If the old glue is left on the frame, it must be carefully removed with alcohol and degrease the surface. The new battery is fixed with special adhesive strips (tear strips), which allow you to retrieve the battery in the future without heating.

Characteristics and Compatibility of Components

When ordering parts, it is important to know the exact model of the device, since the Xiaomi Mi A2 Lite (codename sakura) differs from the regular Mi A2. Below is a table with the main parameters that will help in the selection of components.

Using non-original parts can affect the performance of a smartphone, especially batteries and screens. Cheap copies often have lower capacity or worse color reproduction. Always check the labeling on the display plume before buying.

💡

When replacing the display, always choose a module with a frame - this simplifies the assembly and ensures that there is no dust under the glass.

Assembly of the device and verification of functionality

The assembly is done in reverse order, the battery is installed and connected first, the motherboard is returned to its place and fixed with screws. It is important to check that all the plumes are snapped to the characteristic clicks, otherwise the sensor or image may not work.

Once the plastic panel is installed, you can do the initial test by plugging the display plume and turning the phone on without sticking the back cover. If the image is there and the touchscreen responds, you can proceed to the final stage, and a new layer of glue (B-7000 or special tape) is applied to the frame to fix the back cover.

⚠️ Warning: Do not turn on your phone until you make sure the battery is securely connected and not locked onto metal parts of the case.

The back cover is pressed around the perimeter and fixed with rubber harnesses or a 15-20 minute load to polymerize the glue. After drying, wipe the case of glue residue and check all functions: speakers, microphone, vibration and cameras.

A well-constructed build ensures the device lasts long after repair. If you followed the instructions and used good tools, your Xiaomi Mi A2 Lite will work like new again.

Frequently Asked Questions (FAQ)