Disassembly of the Xiaomi Humidifier moisturiser 2: a detailed guide with photos and tips

The Xiaomi Smartmi Air Humidifier 2 (also known as the Mi Smart Humidifier 2) is a popular device to keep the house in an optimal climate. Over time, even the most reliable equipment requires maintenance: cleaning scale, changing filters or diagnosing malfunctions. However, official documentation from the manufacturer rarely contains detailed disassembly instructions, leaving users one-on-one with plastic latches and fragile parts.

This article will help you safely disassemble the Xiaomi Humidifier 2 humidifier without damaging the body or internal components. We will look at the necessary tools, step-by-step algorithm of actions, and point to the pitfalls that often cause breakages when self-repaired.

Preparation for disassembly: tools and security measures

Before you start dismantling, make sure the device is completely disconnected from the network and the water tank is empty. Residual moisture inside the case can cause short circuits when contacting electronic boards. Also prepare the workplace: cover the table with a soft cloth to avoid scratching on the glossy surfaces of the humidifier.

You will need the following tools:

• 🔧 Plastic mediator (or guitar mediator) - to disconnect the latches of the body without damage
• ✂️ Thin screwdriver with flat sting (2-3 mm) – for unscrewing screws in hard-to-reach places
• 🧴 Isopropyl alcohol (70%+) – for cleaning contacts and control board
• 🧽 Soft toothbrush – removal of scale from the ultrasonic membrane
• 📸 Photography smartphone – capture the location of parts before dismantling

⚠️ Warning: Don't use metal screwdrivers to separate plastic latches! even a slight effort can cause chips on the body.The Xiaomi Humidifier 2 has brittle locks around the perimeter of the bottom lid.

If you are disassembling a scale cleaning device, prepare a solution of citric acid (2 tbsp. per 1 liter of water) or a specialized humidifier. Aggressive chemical compounds (vinegar, household detergents) can damage silicone pads and membranes.

Step-by-step disassembly of the body: from the tank to the electronic board

Starting with the top water tank, this is a simple step, but many users make the mistake of trying to remove the tank by force, which breaks the guides or damages the O-ring.

Algorithm of action:

1. Turn the tank counterclockwise to the point (there is an indicator arrow on the case).
2. Carefully pull the tank upwards, holding the base of the device with the other hand.
3. If the tank is jammed, don't make an effort to see if the residual water in the channels is blocking it.

Once you remove the tank, you'll see an ultrasonic membrane (a round metal disc) and a plastic sprayer, and the most important step is to disassemble the bottom of the case, where the electronics are hidden. Use a plastic mediator to gently separate the latches around the perimeter:

Disconnect the power plug from the board|

Disconnect the humidity sensor wires (orange connector)|

Carefully lift the lid, starting at the corner near the power button |

Take a picture of the location of the screws before unscrewing them.

-->

Under the cover you will find:

• 🔋 Control board with chip and relay
• 💧 Water supply pump (black cylinder with tubes)
• 🔊 Cooling fan (in models with the function of "warm steam")
• 📶 Humidity sensor (small board with metal contacts)

⚠️ Warning: If you notice corrosion on board contacts (greenish coating), don't turn the device on until completely clean! A short circuit in the power supply can disable the control chip.

Cleaning of the ultrasonic membrane and internal components

The ultrasonic membrane is the heart of the Xiaomi Humidifier 2 humidifier, and over time, it forms a limestone plaque that reduces the efficiency of water spraying and can cause an unpleasant odor.

Prohibited activities:

• ❌ Use abrasive sponges or metal scrapers
• ❌ Use aggressive acids (vinegar, hydrochloric acid)
• ❌ Pressing on the membrane is thinner than a human hair!

Recommended method:

1. Wet your soft toothbrush in a solution of citric acid (1:10 with water).
2. Carefully clean the surface of the membrane with circular movements without pressing.
3. Rinse with distilled water and dry the membrane for 10-15 minutes.

To clean the pump and tubes, use a needle syringe (no needle!) to flush the channels under pressure. If high-salt water is left in the system, it crystallizes over time and clogs the lumen of the tubes.

💡

After cleaning the membrane, apply 1-2 drops of silicone lubricant (food!) to the tank seal ring, which will prevent leakage and facilitate assembly.

Diagnosis of malfunctions: when disassembly does not help

If the Xiaomi Humidifier 2 humidifier doesn't work after cleaning, the causes may lie in electronics.

To check the electronics, you'll need a multimeter. Set a constant voltage (20V) mode and check:

• 🔌 Inlet voltage of the board (must correspond to 12V from the power supply)
• 🔄 Voltage at the output of the stabilizer (usually 5V for the chip)
• 🛠️ Membrane resistance (should be within 1.5–2.5 ohms)

⚠️ Warning: If you don't have any experience with electronics, don't try to solder the board yourself. The control chip in Xiaomi Humidifier 2 is sensitive to static electricity. Contact the service center with photos of the board.

Making a humidifier: how to avoid leaks and errors

Building the device after disassembly requires as much precision as dismantling, the main task is to ensure that the system is tight and all parts are positioned correctly.

Assembly order:

1. Install the membrane in the groove, making sure that the contacts match the connectors on the board.
2. Connect the pump tubes, check for no overbending.
3. Lay the humidity sensor wires along the body without twisting them.
4. Close the bottom cover, starting from the side of the power button (there are guide grooves).

Before the final fixation of the latches, perform the test:

• 💡 Connect the device to a network without water in the tank.
• 🔄 Turn on the humidifier and check if the indicator lights up.
• 🚰 Only after a successful test, pour water and check for no leaks.

Replacement of consumables: filters and membranes

The manufacturer recommends changing the filters in Xiaomi Humidifier 2 every 3-6 months, and the ultrasonic membrane every 1-2 years (depending on the hardness of the water).

When you change the membrane, pay attention to the polarity of the connection: red wire - "+", black - "-." Incorrect connection can lead to short circuit. Filters are installed in special slots at the bottom of the water tank - make sure that they fit tightly to the walls.

💡

Using non-original filters can result in a warranty cancellation. If you buy analogues, choose certified models marked "compatible with Xiaomi Smartmi Humidifier 2".

Modernization of the moisturizer: useful upgrades

If you’ve taken apart the device for preventive cleaning, why not improve its functionality? Here are some proven modifications for Xiaomi Humidifier 2:

• 🔄 Installing an external reverse osmosis filter -- it reduces scale by 90 percent -- connects between the tap and the tank.
• 📱 Firmware alternative (for models with Wi-Fi) – adds advanced humidity settings via Mi Home.
• 🔋 Replacing the power supply with a more powerful (15V/2A) will increase the steam intensity by 20–30%.
• 💡 Installation of RGB- backlighting - decorative tank lighting (requires soldering skills).

To install alternative software, you will need:

1. Download the firmware file for your version of the device (check the labeling on the bottom).
2. Connect to the humidifier via Bluetooth via the Mi Home app.
3. In manual mode, download the firmware through the Settings menu → Update.

⚠️ Warning: Electronics modifications void Xiaomi's warranty. If you're not sure about your skills, limit yourself to installing an external filter - it's safe and effective.

FAQ: Answers to Frequent Questions