How to clean the vacuum collector in the robot vacuum cleaner Xiaomi: instructions for all models

Xiaomi vacuum cleaners have become an integral part of a smart home, but their effectiveness depends on the state of the dust collector. 30-50%, But it can also cause engine overheating or sensors to break down, and in this article, we'll look at how to clean the vacuum collector properly in Mi Robot Vacuum, Viomi, Dreame and others, taking into account their design features.

You'd be surprised, but 9 from 10 And the critical mistake that users make is simply to shake out the garbage from the container without removing dust from the filter and sealing gums, and that leads to the accumulation of microbial in the system and the unpleasant smell. We're going to show you how to avoid these problems and prolong the life of your vacuum cleaner. 2-3 year-end.

Why it is important to clean the dust collector regularly

The vacuum collector in Xiaomi robots is not just a garbage container, but part of a complex filtration system, and when the container is more than 70 percent full, the following processes occur:

• 🌀 Reduced suction: The turbine is working to wear out, but air does not pass through clogged filters
• 🔥 Overheating of the engine: the risk of heat protection operation increases (error) 02-0303 new models)
• 🦠 Bacterial reproduction: wet dust + heat = mold-like
• 🚨 False sensors: dust on optical sensors leads to navigation errors

The manufacturer recommends cleaning after each 3-5 cleaning cycles, but in practice the frequency depends on the:

• 🐕 Pets (wool clogs the filter 2 times faster)
• 🏡 Type of coating (carpets vs laminate)
• 🌳 Season (spring/autumn dust 40% more)

Preparation for cleaning: what will be needed

Before you start, prepare the necessary tools.Do not use sharp objects or aggressive detergents - they can damage plastic or rubber seals.

Pay special attention to the choice of detergent. Never use:

• 🧼 Abrasive powders (scraping plastic)
• 🧴 Chlorine products (corroding rubber seals)
• 🍋 Acids (vinegar, lemon juice) – corrodes metal parts)

💡

You can use a solution of water with hydrogen peroxide (1:1) to disinfect, which kills 99% of bacteria and leaves no odor.

Step-by-step instructions for cleaning the dust collector

The cleaning process is slightly different depending on the model, but the overall scheme is the same. Consider the universal algorithm on the example of Xiaomi Mi Robot Vacuum-Mop 2 Pro:

Turn off the robot and remove the battery (if possible)|Open the dust collector lid.|Remove the container and separate the filter.|Remove large debris manually|Wash the container with warm water|Dry all the details for at least 4 hours-->

Step 1: Disconnect and retrieve

Always start with a power outage. In models with a removable battery. D9, Viomi V3) Remove the battery, which will prevent short circuits from getting moisture, and press the lid opening button (usually marked with a pictogram). 🗑️) and carefully pull out the container.

Step 2: Disassembly of the dust collector

Most Xiaomi containers are made up of 3 parts:

1. Main building (waste container)
2. HEPA-filter (usually orange or gray)
3. Preliminary filter mesh (in some models)

Separate the filter by pulling it upwards. Be careful in some models. X10+) filter-mount.

Step 3: Dry cleaning

Remove large debris manually, then use a vacuum cleaner with a narrow nozzle to remove dust from:

• 🌀 Container angles
• 🔄 Duct duct channels
• 🔺 Rubber seals

Step 4: Wet cleaning

Wash all parts (except the filter!) with warm water (temperature not higher than 40).°C. Add a few drops of dishwashing to disinfect. HEPA-filter can only be vacuumed or cleaned gently with a brush - you can not wash it!

Step 5: Drying

This is the most important step. All parts must dry for at least 4 hours at room temperature. Using a hair dryer or heater warps the plastic. Make sure there is no moisture left inside the container, it can lead to a short circuit.

Features of cleaning in different models Xiaomi

The design of the dust collectors varies depending on the series, and here are the key differences:

In the case of the Xiaomi Robot Vacuum X10+, DreameBot X30 Ultra) has an extra storage bag at the dock:

1. Extract every one 15-20 cleaning-cycle
2. Clean with a special brush (comes complete)
3. Change every time. 2-3 month (bags are not washed!)

💡

In robots with wet cleaning function (mop), be sure to wash the water tank after each use - standing water becomes a source of bacteria.

Common Mistakes and How to Avoid Them

Even experienced users sometimes make mistakes that shorten the life of the vacuum cleaner.

⚠️ Never use high-pressure compressed air to clean the filter, which destroys the fibers. HEPA-Reduces filtration by 60 percent%.

Error 1: Cleaning the filter with water

HEPA-Xiaomi robots are made of a special fibrous material that loses its properties when wet, and after washing, it lets up to 30% of the fine dust back into the air:

• 🌀 Soft-filled vacuum cleaner
• 🖌️ A long-pile brush.
• 💨 A compressed air cylinder (hold at a distance of 15 cm)

Mistake 2: Ignoring rubber seals

Dust and fat from sealing rubber over time form a sticky layer that:

• 🔇 Deteriorates tightness (suction power decreases)
• 🦠 Creates a nutrient medium for the fungus
• 🚪 Leads to lid closing errors (03-0401)

Clean the seals with an alcohol napkin every second cleaning.

Error 3: Wet storage of the dust collector

If you assemble the vacuum cleaner before it's completely dry, it creates condensation inside, and that leads to:

• 🔋 Corrosion of battery contacts
• 🛠️ Snatching the mechanism of opening the lid
• 🤧 Allergic reactions in the next use

⚠️ Attention! - LiDAR models (Xiaomi Mi Robot Vacuum) X10+) dust on the sensor lens leads to robot blindness. Clean the lidar glass with a soft napkin without pile every week.

How often should you change the filter and other consumables?

The manufacturer specifies the filter resource in 2-3 This is a month, but in practice, it depends on the intensity of the use:

For models with auto-emptying (DreameBot) L10 Ultra) storage bags are designed to 30-40 They can't be washed or cleaned, they can only be replaced. The original bags have antibacterial impregnation that prevents microbes from multiplying.

When buying consumables, pay attention to:

• 🆔 Compatibility with your model (indicated in the instructions)
• 📦 Certificate of Certificate (fakes are often made from substandard materials)
• 📅 Production Date (filters older than 1 year lose properties)

Prevention: How to reduce dust collection pollution

Compliance with a few simple rules will help to clean the container less often and prolong the life of the robot:

• 🧹 Pre-cleaning: remove large garbage (paper, wires) manually - it quickly clogs the filter
• 🐾 Brush care: Clean the main brush of wound hair weekly (use scissors or a special tool)
• 🚫 Restricted areas: limit cleaning in areas with small debris (animal feed, sand)
• 🌡️ Humidity control: Dry the container more often in damp areas (wet dust sticks together)
• 🔄 Regular replacement of the bag: in models with auto-emptying, do not wait for filling - change the bag with 70% filling

For Xiaomi owners with zoning function (Mi) Home/Xiaomi Home app is useful to create virtual walls around:

• 🍽️ Animal feeding grounds
• 🧺 Laundry basket
• 🎄 Artificial plants (needles clog the filter)

💡

In the Mi Home app, you can set up a cleaning schedule for the time of your absence - so the dust will not soar into the air and settle back on the furniture.

FAQ: Frequent questions about cleaning the Xiaomi dust collector