The Xiaomi M365 is one of the most popular compact vehicles, but even its robust 8.5-inch wheels wear out over time. Cracks on rubber, punctures, loss of grip or just wanting to install stronger tires are all good reasons to replace. But the process of removing and installing a new tire on a tubeless scooter camera requires precision and knowledge of nuance.
Unlike bicycle wheels, where the tire is easily removed by hand, you have to tinker with a hard side and a tight fit on the rim. Without the right tools and machinery, you risk breaking a new tire or damaging the disk. In this article, you have a step-by-step algorithm with a photo, a list of necessary tools, and secrets to make it easier even without a special machine.
What tools will be needed to replace the tire
Before you start, prepare everything you need. Without the right tools, it's almost impossible to remove the old rubber from the Xiaomi M365, because it sits extremely tightly on the rim. Here's the minimum set:
- 🔧 Installation blades (2-3 pieces) - plastic or metal with rounded edges are better, so as not to damage the rim.
- 🔨 Wide carob key (for example, 15 or 17) - for unscrewing the wheel axis.
- 🧴 Soap solution or silicone lubricant – will make it easier to install a new tire.
- 🔥 Hair dryer (optional) - if the rubber "blowns" from the cold, it can be slightly heated for elasticity.
- 🛠️ Cloths and gloves - the wheel will be dirty, and the hands should be protected from the sharp edges of the rim.
The Torx T25 is also useful for unscrewing the wheel bolts to the fork (if you plan to remove the wheel completely). Some craftsmen use a rubber hammer to neatly shrink the tire side, but this is an optional.
⚠️ Warning: Never use screwdrivers or knives instead of mounting blades! Sharp edges will cut a new tire or damage the tubeless tire sealant.
How to remove an old wheel from a scooter Xiaomi M365
The first step is to dismantle the wheel, and the key is to take your time and not make too much effort to avoid bending the axle or tearing the thread.
- Turn the scooter upside down and fix the steering wheel so that it does not fall (you can put the book under the base).
- Unscrew the axle bolt with a carob key. On the M365, it is usually tightly tight - if it does not go, splash the WD-40 and wait 5 minutes.
- Remove the wheel from the fork. If it sits tight, gently tap the rubber hammer on the axis on the back.
- Disconnect the brake cable (if it interferes) and the ABS sensor wire (on the rear wheel).
Now the wheel is ready to replace the tire. If you're taking it off for the first time, pay attention to the direction of rotation (indicated by the arrow on the sidewall of the rubber) - you need to put the new tire in the same way.
💡
Before removing the wheel, take a picture of the location of all the bolts and cables, which will help to avoid errors in the reverse assembly.
Step-by-step: how to remove the old tire
The hardest part is to separate the hard side of the rubber from the rim, and you'll need the mounting blades and patience.
Algorithm of action:
- Release all air from the chamber (if any) or tubeless tire by pressing the nipple.
- Insert the first mount between the rim and the side of the tire, retreating 10-15 cm from the nipple. Lock it by hooking it up by the spoke.
- Insert the second mount 5-7 cm from the first and carefully turn the side outwards. Repeat the process, gradually moving in a circle.
- When one side of the tire is freed, pull out the camera (if there is one) or simply remove the rubber from the rim.
If the rubber is stuck to the rim, spray it with WD-40 or soap solution. Don't try to tear the side by force, you will tear the tire or bend the disc.
Remove old sealant from rim | Check rim for no burrs | Put on new tire with the right side (rotation arrow) | Lubricate the side of the tire with soapy solution-->
How to install a new tire on the rim
Installation of new rubber is no less painstaking than removing the old one, and the main difficulty is filling the side of the tire under the rim, especially if it is tight (for example, anti-piercing models).
Take steps:
- Put the tire on the rim, starting from the side opposite the nipple, and make sure that the arrow of the direction of rotation matches the movement of the wheel.
- Squeeze the side of the tire into the central groove of the rim - this will facilitate the refueling of the second side.
- Start filling the other side with a nipple, gradually moving in a circle. Use mounting blades, but without undue effort.
- The last section (usually 10-15 cm) will be the most difficult, and this will help with soap solution or silicone lubricant - apply it on the tire.
If the tire doesn't sit down, try pumping it to 0.5-1 bar, and the pressure will help the ship to get back in place.
⚠️ Warning: If you hear the air whistling after pumping, you're not fully engulfed in the rim, you need to let the air out and repeat the refueling.
What to do if the tire does not sit on the rim?
How to pump the wheel after replacing the tire
Once the tire is successfully installed, the last step is to pump the wheel, but there are nuances to this, especially if you have a tubeless tire.
Instructions:
- 🔧 Connect the pump to the nipple and pump in short jerks, checking how the board sits down.
- 🎯 Optimal pressure for Xiaomi M365 — 35–50 PSI (The exact value is shown on the sidewall of the tire.
- 🔊 If you hear hissing, stop pumping, let the air out and check if the board has evenly sat down.
- 💦 For tubeless tires after pumping, you can slightly shake the wheel to the sides - this will help the sealant fill the microcracks.
After pumping, check the wheel for a beat, scroll through it and see if there are any deviations, and if the wheel is eight, then the tire is uneven or the rim is bent.
| Type of tire | Recommended pressure | Features of pumping |
|---|---|---|
| Standard Xiaomi (8.5) | 35–45 PSI | Pump smoothly, avoiding sharp pressure surges |
| Enhanced anti-procolour | 40–50 PSI | It requires more effort when refueling the board |
| tubeless tyre | 30–40 PSI | After pumping, check for leakage with soap solution |
| Winter studded | 28–35 PSI | Pressure below standard for better grip |
Which tires are better to choose for Xiaomi M365
The standard Xiaomi M365 tires wear out in about 1,000-1,500 km of active driving, and can be replaced with more durable ones:
- 🛡️ Anti-procolour (e.g. Kenda) K193 or CSL Solid – thicker and more resistant to cuts, but heavier.
- ❄️ Winter (e.g. Xiaomi Winter Tire) – with spikes or soft rubber for driving in the snow.
- ⚡ Slicks (like Honeycomb Solid) – smooth for high-speed asphalt driving, but slippery on wet roads.
- 🔄 Universal (for example, Mibao) - the middle option between grip and wear resistance.
When choosing, pay attention to:
- The diameter is only 8.5" (for M365 8" or 10 "will not work").
- Type - chamberless or chamber (specify what was originally).
- Side rigidity – soft tires are easier to install, but they are less protected from punctures.
💡
For urban driving, the optimal option with a reinforced cord (for example, Kenda K193) is 2-3 times longer than standard rubber and better holds pressure.
Frequent Mistakes and How to Avoid Them
Even experienced users sometimes make mistakes when replacing tires with the Xiaomi M365.
- 🔄 Incorrect direction of rotation – the arrow on the tire should coincide with the movement of the wheel forward.
- 💥 Wheel pumping - pressure above 50 PSI may cause the tire to rupture.
- 🛑 Ignoring the beat – if the wheel is curved, it will accelerate the wear of bearings.
- 🧼 Lack of lubrication – without soap solution or silicone, the side of the tire can break when installed.
- 🔧 Using inappropriate tools - screwdrivers or knives damage rim and rubber.
Another common problem is air leakage after replacement.
- Badly sunk side of the tire.
- A damaged nipple or rim.
- A low-quality sealant (for tubeless tires).
If the wheel is coming down, apply the soap solution to the rim, and bubbles will appear at the leak site, then release the air, adjust the side and pump again.