How to get it safely SIM-map from Xiaomi Redmi 6A: photo-instruction

Xiaomi Redmi 6A — One of the most popular budget smartphones released in 2018, but still in active use. SIM-cards from this device can cause difficulties for beginners: an uncomfortable tray, a fragile plastic case and the risk of damaging the microphone or speaker with careless actions. In this article, we will analyze all ways of extracting the SIM - from the standard using a paper clip to emergency methods, if the tray is jammed.

Feature of Redmi 6A in that his SIM-The tray is combined with a slot for a microSD memory card, and the fixation mechanism itself is less reliable than in flagship models. If you have never opened a tray or are doing it for the first time, we recommend that you carefully read the instructions - improper extraction can lead to breakage of contacts or dust entering the connector. We will also tell you how to avoid typical errors and what to do if the SIM card is stuck.

Preparation for extraction SIM-maps: what you need

Before you start extracting, make sure you have everything you need. Unlike modern smartphones, where the tray is often pushed out with your finger, the Redmi 6A requires a special tool to do this. Here is the full list:

• 🔧 clip or needle to be removed SIM (It comes with a phone, but it's often lost, and any thin metal wire up to 0.8 mm in diameter will do.
• 📱 Good lighting – the tray is located on the side, and in the dark it is easy to miss the hole.
• 🧴 Alcohol wipes (optional) – if the tray contacts are oxidized or contaminated.
• 🔍 Lupa (optional) – will help to consider small details if the sim stuck.

If you do not have a brand name, you can use:

• 🖊️ The rod from the gel handle (pre-remove the paste).
• 📎 A pin or stud (tighten the tip so as not to scratch the body).
• 🪡 Needle from a sewing machine (the thinnest and most reliable option).

⚠️ Warning: Never use toothpicks, matches or plastic items – they may break inside the hole and you will have to disassemble the phone.

Turn off your smartphone before you start, not necessarily to retrieve the SIM, but it will help you avoid accidental taps on the screen and save battery power, and make sure that there is no mechanical damage on the tray, such as cracks or chips, if any, you should contact the service center.

Wherever SIM-tray in Xiaomi Redmi 6A

At Redmi. 6A squash SIM-The map is located on the left end of the case (when you look at the screen face). This is standard place for most Xiaomi models, but unlike flagships, there is no backlight or tactile mark. The extraction hole is next to the volume buttons and has a diameter of about 1 mm.

In order not to confuse the tray with other connectors, focus on:

• 📍 Location relative to the buttons – the hole is 3-4 mm below the volume button.
• 🔍 Marking – there may be a barely noticeable icon next to the hole SIM-maps (two rectangles).
• 🎧 3.5mm audio jack – the tray is on the opposite side of it.

If you are not sure you found the right hole, compare it to the photo below (short name):

|                   |




| ECRAN |




|                   |




| [ON button] |




|                   |





| [] [] | ← Volume buttons




| (hole) ← SIM Lot

⚠️ Note: Do not confuse the hole for SIM-The microphone in Redmi. 6A It's located on the bottom end next to the microUSB connector. If you put a paper clip in there, you risk damaging the membrane.

💡

If the hole is clogged with dust, clean it carefully with a toothpick soaked in alcohol. Don't use wet wipes - they can leave a pile!

Step-by-step: how to remove the tray from the SIM-card

Now, let's get to the process. Follow the instructions Step-by-step to avoid mistakes.

1. Turn off your phone (optional, but recommended).
2. Take a paper clip and insert it into the hole at a 90 degree angle to the body, so you don't have to push hard enough, just press it to the click.
3. The tray should be extended by 1-2 mm. After that, carefully pull it with your fingers until completely removed.
4. If the tray does not come out, do not pull it by force - check if the contacts are hooked on the body (see the section "What to do if the tray is jammed").

The visual process looks like this:

Make sure the phone is off | Check the integrity of the paper clip | Press the tray without fanaticism | Remove the tray smoothly, without jerking-->

In the Redmi 6A tray there are places for:

• 📱 Two nano-SIMs (or one nano-SIM) + microSD).
• 💾 Memory cards (if one is used) SIM).

Notice the marking on the tray, which indicates which side to insert the SIM, the contacts should be directed downwards, and the bevelled angle should match the shape of the tray.

💡

At Redmi. 6A two should not be used SIM-card and memory card at the same time, only two SIM, one SIM + microSD.

What to do if the tray is jammed or does not come out

If the tray doesn't extend after you press it, don't panic.

• 🔧 Dust or dirt in the mechanism is the most common problem. Try blowing the hole with compressed air (for example, a canister to clean the keyboard).
• 💧 Contact oxidation - if the phone was in a wet environment, the metal parts could rust. WD-40 (carefully!).
• 🔨 Mechanical deformation -- if the phone fell, the tray could bend.

Algorithm of actions during jamming:

1. Try pressing the paperclip at different angles (sometimes the mechanism works only at a 45 degree inclination).
2. If the tray is moved halfway, do not pull it by force - gently swing left-right, while putting on a paper clip.
3. As a last resort, use a flat screwdriver by putting the tray on the side, but it's risky to scratch the body.

If nothing works, try to warm the body with a hair dryer (temperature no higher than 50°C) — sometimes it helps with oxidation. But don't overdo it: overheating can damage the battery.

How do you put it in? SIM-Map back: important nuances

Remove the tray is half the battle, and it's just as important to put it back in the right way to avoid communication problems or damage to your contacts.

• 📱 Check the SIM for damage -- if the contacts have scratches or chips, the card may not work.
• 🔄 Observe orientation – the bevelled angle should coincide with the shape of the tray, and the contacts should be directed downwards.
• 🧲 Don't force it, the tray must enter smoothly. If you feel resistance, check if the dust has entered the grooves.

After installation:

1. Then, put the slack down (there is a slack).
2. Turn on the phone and check the signal level.
3. If the network is not catching, restart the device or check the settings Settings → SIM-maps and mobile networks.

If the SIM is not determined after installation, the reasons may be as follows:

Frequent Mistakes and How to Avoid Them

Even in a process as simple as extraction. SIM-And these are the most common mistakes that people make:

• 🔨 Using inappropriate tools like toothpicks, knives, forks, and that leads to scratches on the body or breakage of the machinery.
• 💦 Moisture intake – if you cleaned the tray with a wet wipe, be sure to dry it before installing it.
• 🔄 Mixed SIMs – If you have two cards, remember which slot was the main one (usually slot 1 supports the same card). 4G).
• 📵 Removing the tray when the phone is turned on - this will not damage the device, but can lead to a network failure.

To avoid problems:

• 🧹 Clean the tray regularly - once every 3-6 months, blow the hole from the dust.
• 🔋 Do not remove the SIM when the battery is low – if the phone turns off during the process, network settings may be confused.
• 📦 Keep the tray in a safe place – if you take it out for a long time (for example, when selling a phone), put it in an antistatic bag.

If you change often SIM-cards (for example, when traveling abroad), consider buying an adapter for two SIMs or using eSIM (although Redmi is a good choice for the two SIMs). 6A He doesn't support it).

💡

If you travel frequently, buy a multi-sim (for example, from Tele2 or MTS) – it allows you to use multiple numbers on one physical card without constant replacement.

Alternative methods of extraction SIM-cards (if there is no paper clip)

Sometimes there is no paper clip at hand or it is broken, in which case you can use the tools at hand, but with caution:

• 📎 Paperclip for papers - unbend it and cut off a piece 3-4 cm long.
• 🪡 A needle is only a thin sewing needle, and dull needles (for example, knitting) will not fit into the hole.
• 🖊️ The handle bar -- take out the paste and use a plastic tube.
• 📌 The stationery button, if thin enough, wrap the tip with tape beforehand so you don't scratch the body.

If none of the above is available, you can try the sticky tape method:

1. Stick a piece of tape to the protruding edge of the tray (if it is pushed at least 1 mm).
2. Carefully pull the scotch to pull the tray out.
3. Make sure there is no glue left on the contacts.

This only works if the tray is a little extended, and if it's completely drowned in the case, the tape won't help.

⚠️ Warning: Never use a knife or scissors! sharp blade can slip and injure your fingers or damage the phone's internal components.

FAQ: Answers to Frequent Questions