Xiaomi is stuck on the boot: what to do if the device does not turn on beyond the logo

Your Xiaomi Mi. TV, A Redmi smartphone or a Pad tablet suddenly stopped loading beyond the logo? The screen flashes, "Mi" appears and everything repeats in circles? This problem is familiar to many users of Xiaomi equipment, and in 80% of cases it can be solved independently without contacting the service. The reasons for this behavior of the device vary from a banal firmware failure to hardware malfunctions, but the diagnostic algorithm is always the same: first we check software methods, then hardware.

In this article, we will analyze all possible scenarios when the Xiaomi device is getting stuck on the boot: from a simple reset settings to flashing through Fastboot or recovering through the Fastboot. EDL-You'll learn how to tell a software failure from a motherboard failure, what tools you'll need to repair it, and what to do if you see errors like No command or Orange State on the screen. Particular attention will be paid to data preservation – because often freeze occurs after an unsuccessful update, when important files remain in the device memory.

Before you start, answer two key questions: 1. Haze occurred after updating the firmware, installing the application or physical impact (falling, getting moisture)? 2. Does the device respond to buttons pressing (for example, the Power combination) + Volume Up)?

The choice of the recovery method depends on the answers.

1. Reasons Xiaomi gets stuck on the logo

Loading freezes (called bootloops) are a symptom, not a diagnosis. To properly treat them, you need to understand the root cause, POCO mi TV) The problem most often arises from:

• 🔄 Failed firmware updates – interrupted download OTA, error when unpacking files or version conflict (for example, attempt to put a file in the file) MIUI 14 on a device that officially supports only MIUI 12).
• 📱 Damage to system files – due to viruses, manual removal of system applications (for example, through ADB) or file system failure ext4/f2fs.
• 🔋 A discharged or faulty battery – if the voltage has fallen below a critical level (e.g, 3.2V), Power controller blocks loading.
• 🛠️ Hardware malfunctions - oxidation of contacts on the motherboard, the dump of memory chips (eMMC or UFS), bootloader damage.
• 🔌 Conflict with custom firmware – for example, installing LineageOS without the correct TWRP or incompatible kernel.

Unlocked bootloader devices are particularly vulnerable, as users often experiment with firmware. For example, the Xiaomi Redmi Note 10 Pro may go to bootloop after trying to put the Pixel Experience without first cleaning the vendor partition.

⚠️ Warning: If the freeze occurred after a device fell or moisture hit, DO NOT try to sew it - first check the integrity of the board.

2.First steps: mild reboot and power check

Before you start complex manipulations, do the basics, which are 30 percent effective and don't require any special knowledge.

Forced reset

If the device responds to buttons, try combinations:

• 🔄 For smartphones: pinch the Power + Volume Up for 10-15 seconds until the screen goes out. Then turn on the device with the Power button.
• 📺 For Mi TVs, TV: Turn off the power from the socket for 1 minute, then turn it back on. If there is a reset button (usually on the back), press it with a paper clip.

If after the reboot appears Recovery menu (black screen with blue text), select Reboot option → If the device goes back to bootloop, move on to the next step.

Checking of the battery and the power supply

Low charge or unstable power is a common cause of hanging.

• 🔋 Connect the device to the original charger (for smartphones – cable) USB-C Wait 30 minutes, even if the indicator is not on.
• 🔌 For Mi. TV: Try another power cable or power outlet, and if the TV turns on but turns off, the problem is the power supply.
• 🔍 Visually inspect the charging connector for oxidation or damage.

⚠️ Warning: If the device heats up after charging, but does not turn on, this may indicate a short circuit in the power supply chain.

3. Enter Recovery Mode and Reset Settings

If the soft reboot didn’t work, the next step is to enter Recovery Mode, a built-in menu that lets you reset settings, clear your cache, or install the update manually.

3.1 How to log in to Recovery on Xiaomi smartphones

For most models (Redmi Note 11, POCO X3, Mi 11 and others.):

1. Turn off the device (press the Power for 10 seconds).
2. Press Power + Volume Up and hold until the Mi logo appears.
3. Release the buttons – the menu should open. MIUI Recovery (blue text on a black background).

For Mi TVs:

1. Shut down the power.
2. Press the Menu button on the remote and the Power button on the body at the same time.
3. Hold on until the recovery menu appears (usually 10-15 seconds later).

Cleaning the cache and data resetting

In the Recovery menu, use volume buttons for navigation and Power to select.

• 🧹 Wipe Cache - clears temporary files. Does not delete user data, but can help if the freeze is caused by cache damage.
• 🔄 Wipe Data (Factory Reset) — a complete factory reset that will delete all data, but often it's the only way to bring a device back to life.
• 📥 Apply update from ADB — If you have a firmware on your computer, you can install it through ADB sideload.

If the device doesn't boot after Wipe Data, the problem is deeper, the boot or system partition is damaged, and you'll need to flash it back.

4. Firmware through Fastboot: step-by-step instructions

If resetting didn’t work, the next step is to run the firmware through Fastboot mode, which is suitable for most Xiaomi devices, except those that have a damaged bootloader.

• 🖥️ Windows computer (or Linux/macOS driverless ADB).
• 🔌 Cable USB-C (preferably original).
• 📦 Official firmware for your model (download from the site) MIUI Downloads).
• 🛠️ Mi Flash Tool (for Windows) or fastboot from Android SDK.

Preparation for firmware

Download the firmware in.tgz or.zip and unpack it into a folder. Important: choose the version for your model (for example, Redmi Note 10 Pro has the code name sweet, and the name is not too bad). POCO X3 NFC — You can find out the code name on the Xiaomi Flash website.

Install the drivers:

• For Windows: Download Qualcomm Drivers (if you have a Snapdragon processor) or Android SDK.
• For Linux/macOS: Install fastboot via a packet manager (e.g., sudo apt install fastboot).

The firmware process

Connect the device turned off to the computer, holding Volume Down. in Device Manager should appear Qualcomm device HS-USB QDLoader 9008 (for Snapdragon) or Android Fastboot.

Open the command line in the firmware folder and do:

fastboot devices

If the device is determined, enter:

fastboot flash boot boot.img


fastboot flash recovery recovery.img




fastboot flash system system.img




fastboot reboot

For full flashing, use the Mi Flash Tool:

1. Select a folder with unpacked firmware.
2. Press Refresh – the device must be determined.
3. Select Clean All (deletes all data) or Clean All and Lock (blocks the bootloader).
4. Press Flash and wait until it is completed (5-10 minutes).

⚠️ Note: If the firmware is interrupted with a critical partition flashing error is not allowed, you have the bootloader blocked. Unlock it through the Mi Unlock Tool (requires a Mi Account and wait 7-14 days).

💡

If after firmware the device goes back to bootloop, try flashing an older version. MIUI. For example, the Redmi Note 9 Pro instead of the Redmi Note 9 Pro. MIUI 14 set up MIUI 12.5 – This often solves compatibility issues.

5. Recovery through EDL-regime (for “bricks")

If the device does not respond to buttons at all, is not determined in Fastboot and does not turn on, there is a last chance - firmware through the Fastboot. EDL-Emergency Download Mode: This method works even if the bootloader or recovery partition is damaged, but requires special equipment and knowledge.

5.1 When necessary. EDL?

• 🧱 The device does not turn on, does not vibrate, does not respond to charging.
• 🔌 Device Manager is defined as Qualcomm HS-USB QDLoader 9008.
• 📵 Fastboot Firmware Ends with Remote: Device Is Locked.

Instructions for firmware in EDL

You'll need:

• 🖥️ Mi Flash Pro or QFil (for Qualcomm chips).
• 📦 Firmware in.mbn or.elf format (see forums like this). XDA).
• 🔧 Test Point (for forced transfer to the EDL — will require disassembly of the device).

Algorithm:

1. Disassemble the device and find Test Point (for each model it is its own, look for schemas on the device). GSM Arena).
2. Close the Test Point contacts and connect USB-cable – the device must be identified as QDLoader 9008.
3. In Mi Flash Pro, select firmware and press Flash.
4. Wait until it is completed (it can take up to 20 minutes).

Firmware through EDL It resets all the data and can block the bootloader. Use this method only if other methods have not helped.

💡

EDL-The mode is a "resuscitation" for devices that do not respond to other methods, but it requires disassembly and risks permanently blocking the bootloader if you use informal firmware.

6. Hardware malfunctions: when to carry in the service

If all software methods have been tried, but the device still doesn't turn on, the problem is likely hardware.

• 🔋 Failed battery: bloating, short circuit or loss of capacity. Symptoms: the device only turns on from charging, but immediately turns off.
• 🧠 Damage to memory chips (eMMC or UFS) — Symptoms: The device is defined as QDLoader 9008, but firmware does not help.
• 🔌 Oxidation or breakage of contacts on the motherboard. Symptoms: accidental reboot, lack of response to buttons.
• 📡 Power controller failure – the device does not charge, does not turn on, but sometimes vibrates.

How to diagnose:

• 🔍 Visual inspection of the board for darkening, oxidation or detached elements.
• 📊 Checking the multimeter voltage on the battery (should be) 3.7V–4.2V).
• 🔧 Short-circuit test (if the cable is heated when connected to charging).

⚠️ Note: If you have no experience in the squashing BGA-chip, don't try to repair the board yourself. Incorrect heating can permanently disable it. In such cases, it is optimal to contact the Xiaomi service center or a proven workshop.

7.Prevention: How to avoid hanging in the future

To prevent your Xiaomi device from going to bootloop, follow these guidelines:

• 🔄 Update your firmware only through official channels (Settings) → About phone → Avoid "custom" firmware if you are not sure of its compatibility.
• 🔋 Keep the battery from running out of power. Charge the device at 15-20 charge level%.
• 📱 Do not delete system applications without root rights. This can damage files that are critical to download.
• 🛡️ Use high-quality cables and chargers. Cheap accessories can cause power surges.
• 🔍 Check your battery health regularly through apps like AccuBattery (for Android).

If you like to experiment with the scalp:

• 🔓 Unlock the bootloader in advance through the Mi Unlock Tool (you will need to link your Mi Account).
• 📦 Make a backup section. EFS (contain IMEI and serial numbers) by means of TWRP or ADB.
• 📡 Check compatibility on forums before firmware XDA or 4PDA.

💡

Before updating the firmware through OTA Check the reviews of other users on the forums, MIUI 14 for Redmi Note 9 had bugs with a freeze on the boot — many solved the problem by rolling back on the MIUI 13.

FAQ: Frequent questions about Xiaomi hanging