How to turn off Xiaomi smart watches: from Mi Band to Watch 2 Pro

Xiaomi smartwatches are not just an accessory, but a full-fledged gadget with its own processor, battery and operating system. However, many users face difficulties when trying to turn them off: somewhere there is no obvious power button, somewhere the menu is hidden in the depth of settings, and some models do not support a standard shutdown. In this article, we will discuss all possible ways to turn off the Mi Band, Amazfit and Xiaomi Watch lines, including emergency methods and nuances for specific models.

It's important to understand that the procedure varies depending on the firmware version, model, and even the region of release. For example, the Mi Band 7 with firmware for China may have a different algorithm than the European version of the same device. We took these features into account and put together universal solutions that will work in 95% of cases. If your watch does not respond to standard actions, check the alternative methods section or the compatibility table at the end of the article.

Why you can’t turn off Xiaomi watches

Before we get to the instructions, let’s look at the typical reasons why users can’t turn off the device:

• 🔋 Low battery charge: some models (e.g. Amazfit) GTR 4) block access to the off menu at a charge level below 5%, this is done to prevent a full discharge that could damage the battery.
• 🔒 Child Mode or Lockdown: The enabled Safe Mode or parental controls may restrict access to system settings.
• 📱 Communication with the phone. Xiaomi Watch S1 and some versions of the Mi Band do not allow you to turn off if they are connected to the smartphone via Bluetooth and there is a synchronization of data.
• 🛠️ Firmware failure: After a failed update or reset, the menu may not work properly and the buttons may not respond to clicks.

If your case doesn’t fall under these points, but the clock still doesn’t turn off, try a forced reboot (Section 4) or check the device for physical damage (such as moisture hitting a button).

⚠️ Note: Watches Xiaomi Mi Band 3/4 They don't have a full shutdown function, basically -- just a reboot. It's because of the architecture of their firmware. Attempting to pull the battery out or disassemble the case will result in a loss of warranty.

Method 1: Standard shutdown via the settings menu

This is the most obvious and safest method that works on most models, including the Xiaomi Watch. 2 Pro, Amazfit GTS 4 and Mi Band 7/8. The instruction is suitable for devices with a touch screen:

1. Swipe your finger up the screen to open the main menu.
2. Find the Settings icon (cog) and tap it.
3. Scroll down to System or About Phone (on some models – About Device).
4. Choose to Turn Off or Reboot (on the Mi Band it can be called Restart).
5. Confirm the action by holding the button on the screen (usually 3-5 seconds).

On a physical button watch (such as the Amazfit Bip U Pro), the path may be different:

1. Press one button to unlock the screen.
2. Hold the same button for 3-4 seconds until the menu appears.
3. Select Power Off with swipes and confirm the choice.

Charge the clock to at least 10%|Turn off the phone (if sync is active)|Close all background applications (music, training)|Take your watch off your hand for convenience.-->

💡

If the screen doesn’t respond to swipes, try to wipe it with a dry wipe – sometimes fat or moisture is the cause.

Method 2: Shutting down via the Mi app Fitness/Zepp

For models that don’t have an explicit option to turn off the menu (such as the Mi Band 5 or Amazfit Neo), you can use the official app, which is also useful if the touch screen is damaged but the watch is still connected to the phone.

Instructions for Mi Fitness (for Mi Band):

1. Open the app and select your device at the top of the screen.
2. Go to the Settings section of the device (the gear icon next to the watch name).
3. Scroll down to the item Additional → Reset the device.
4. Confirm action. The watch will reset (there will be no full shutdown, but it is the only option available for some models).

Instructions for Zepp (for Amazfit):

1. In the main menu of the application, tap the icon of your watch.
2. Select the Device → Settings → System settings.
3. Find the item “Switch off” or “Restart” (on some firmware it is hidden behind additionally).
4. Follow the instructions on the screen.

⚠️ Note: After rebooting through the app, the Amazfit T-Rex 2 watch may reset the notification settings. → Profile → Backup.

Mi Band 5/6/7/8|Xiaomi Watch S1/S2|Amazfit GTS/GTR|Amazfit Bip|Another model|I don't know.-->

Method 3: Forced reset (hard reset)

If the clock is getting stuck, doesn't respond to touch, or standard methods don't work, hardware reboot will help, which works on all models, but can result in the loss of unsaved data (e.g., an ongoing workout).

General instructions for most devices:

1. Remove the watch from your hand and place it on a flat surface with the screen up.
2. Find the physical button (on the Mi Band is the touch area under the screen, on the Amazfit is the side button).
3. Hold her down. 10–15 seconds until the screen goes out and the logo lights up. Xiaomi/Amazfit.
4. Release the button and wait for the full download (can take up to 2 minutes).

Features for specific models:

• 📱 Xiaomi Watch S1: Hold both buttons (top and bottom) at the same time for 10 seconds.
• 🔄 Amazfit GTR 3 Pro: Press and hold the power button + Touch the screen with your finger for 8 seconds.
• ⚡ Mi Band 4: Place the watch on charge, then hold the touch button for 20 seconds (only works when connected to the device). USB).

Method 4: Turn off through Developer Mode (for Advanced)

This method is suitable for models based on Wear OS (For example, Xiaomi Watch 2 Pro) or devices with unlocked options for developers, it allows you not only to turn off the clock, but also to access hidden settings.

How to turn on the developer mode:

1. Open on the clock Settings → The phone.
2. Find the assembly number or version of the software.
3. Slap it 7 times in a row until the notice "You became a developer" appears.

Next:

1. Go back to the main settings menu and find a new section for developers.
2. Activate the Debugging option ADB.
3. Connect the watch to your PC via Bluetooth or Wi-Fi (instruction below).
4. Enter the command line: adb shell reboot -p That'll turn the device off.

To connect via ADB:

• 🖥️ Install Android Studio or Minimal ADB.
• 🔌 Turn on the clock debugging over Bluetooth in the developer menu.
• 📱 Connect the watch to your PC through the Wear app OS (Xiaomi Watch 2 Pro).
• 💻 Enter the commands: adb pair [MAC-address of the clock [MAC-clock] (MAC-Address can be found in Settings → The phone. → Status)

⚠️ Attention: Use ADB This can cause you to lose warranty if you change system files.Adb shell reboot command -p Safe, but other operations (such as adb shell rm) can damage the firmware.

Method 5: Emergency shutdown by charging

If the watch is completely getting stuck, unresponsive to buttons and sensors, but still showing signs of life (vibrating, flashing indicator), you can try the method of discharge through the charger. It works thanks to the features of the power controller in Xiaomi devices.

Step-by-step:

1. Connect the watch to the charger (use the original cable).
2. Hold the power button (or touch area on the Mi Band) for 30 seconds.
3. Turn off the cable from the clock without releasing the button and keep holding it for another 10 seconds.
4. Connect the cable back, the clock should reset.

This is a technique that works by resetting the power controller, and it's particularly effective for models like:

• ⚡ Mi Band 6 (if the screen shows the logo but does not respond to touch).
• 🔋 Amazfit Bip S (on infinite download after update).
• 📉 Xiaomi Watch Color 2 (if charging animation is hanging).

💡

The method of charging is the only way to “reanimate” the Mi Band watch 3/4, which do not have a hardware switch off button.

Table of compatibility of methods for popular models

To make it easier for you to navigate, we have collected data on support for each shutdown method for different devices, and if your model is not in the table, use methods 1 and 3 (standard menu and hard reset).

Note: Mi Band 1-4 models are not fully shut down – these devices only support reboot. If you need to reset them to factory settings, use the hard reset method (Section 3).

Frequent Mistakes and How to Avoid Them

When you try to turn off Xiaomi watches, users often make common mistakes that can make the problem worse, and here are the most common ones and ways to prevent them:

• 🔌 Pulling the cable out during the upgrade. If the clock is updated (load indicator is on), never turn it off the power. This can lead to a breeze (complete failure). Wait for the process to finish or, if it is frozen, use the charging method (section 5).
• 💦 Trying to disassemble the case. Xiaomi watches are not designed for self-repair, their body is glued together, and the battery is not removable. Disassembly without special tools will damage the plumes.
• 🔋 Use of non-original chargers. Cheap cables may not provide the voltage required, which makes hard reset work. Always use the original cable or certified counterpart.
• 📱 Turning off Bluetooth on your phone during a reset. If you turn off the clock through the app, don't interrupt the connection until the process is complete.

If the clock stops turning on after turning off, try the following:

1. Connect them to charge for 1-2 hours (even if the indicator does not burn).
2. Press and hold the power button for 20-30 seconds.
3. If it doesn’t work, try connecting to another power source (for example, a PC via a power source). USB).

💡

If the Amazfit watch doesn't turn on after turning off, try charging it in the fridge for 10 minutes (in a package to avoid condensation).

FAQ: Answers to popular questions