Reset headphones Xiaomi Haylou GT1: 5 ways to return factory settings

Why You Need to Reset Your Haylou GT1 Headphones and When to Use It

Headphones Xiaomi Haylou GT1 — one of the most popular TWS-And even though they're not immune to software failure, resetting to factory settings solves 90 percent of the problems that come with connecting, sounding, or sensors. For example, if the headphones stopped synchronizing with each other, are not determined by the phone or emit intermittent sound – the first thing you should try is a “hard” reset.

Unlike the newer models (Haylou GT6 or GT7), the GT1 doesn't have a separate reset button - the procedure is done through a combination of taps. This often causes confusion: users try to hold the touchpad or the on button, but nothing happens. In fact, the algorithm depends on the firmware version and even whether the headphones are connected to the charging case at the time of reset.

It’s important to understand the difference between a soft reset (reboot) and a full reset (return to factory settings). The first simply restarts the device without affecting the pairing settings, and the second erases all pairing data, returning the headphones to the “out of the box” state. In this article, we’ll discuss both options, as well as the rare cases when the reset does not work – and what to do then.

Method 1: Classic button reset (for all GT1 versions)

This is a versatile method that works on the Haylou GT1 of any revision (including versions with V1.2.8 firmware and later).The main condition is that the headphones must be removed from the case and be turned off. If they flash or make sounds, first turn them off with a long press of the touch panel (5-7 seconds).

Step instructions:

1. Turn off both earbuds. To do this, hold the touchpad on each of them for 5-7 seconds until the indicator goes out.
2. Press the touch panels on both headphones simultaneously. Press and hold both panels with your fingers for 10-15 seconds.
3. Wait for the reset signal. First, the indicators will flash red, then the beep will sound (usually two short squeaks), and the headphones will turn off.
4. Turn on the headphones again. Now they're in pairing mode (the indicator flashes red and white).

If the headphones do not connect to the phone after reset, try:

• 🔄 Remove them from the list of associated devices in Bluetooth settings.
• 📱 Reboot your smartphone (especially relevant for Xiaomi on the Internet) MIUI 12+).
• 🔋 Put the headphones in the case for 10 minutes, then repeat the procedure.

⚠️ Warning: If the headphones flash only red and do not go into pairing mode, this means that the reset has not occurred. Repeat the procedure, holding the panels longer (up to 20 seconds).

Make sure the headphones are charged (minimum 30%).

Turn off Bluetooth on all devices within a 5-meter radius.

Use dry fingers – moisture can interrupt contact.

Do not put your headphones in the case until the procedure is completed.-->

Method 2: Reset via Haylou Fun (for V1.3.0+ firmware)

The official Haylou Fun app (available for Android and iOS) allows you to reset your headphones software without resorting to “iron” manipulations, which is useful if physical buttons do not respond or you are afraid of damaging sensors, but it only works on headphones with firmware V1.3.0 and higher.

Step-by-step:

1. Install Haylou Fun from Google Play or the App Store.
2. Connect the GT1 headphones to the app via Bluetooth.
3. Go to the Device → Settings → Resetting.
4. Confirm the action and wait for the headphones to restart (it will take ~30 seconds).

Advantages of this method:

• 🛠️ No risk of damaging sensors with prolonged pressing.
• 📊 The app shows the current firmware version and charge level.
• 🔄 You can update the software immediately after reset (if a new version is available).

If the application does not have a reset button, then your version of GT1 does not support this feature, in which case use method 1 (through buttons) or update the firmware manually.

Through the buttons on the headphones.

Through the Haylou Fun app

Never dropped it.

Another way.-->

Method 3: Reset after a failed firmware update

If Haylou GT1 headphones stop working after a firmware update (e.g., it's stuck on the logo or not turned on), a standard reset may not work, in which case a forced reset with firmware rollback is required. This method is risky - if you do the wrong thing, the headphones can turn into a "brick", but in 80% of cases it saves the device.

Algorithm of action:

1. Put both headphones in the charging case and close the lid.
2. Connect the case to the power source (charger or Power Bank).
3. Hold the button on the case (located at the back) for 20 seconds.
4. Release the button when the indicators on the case start flashing red and green alternately.
5. Remove the headphones from the case - they should automatically turn on in pairing mode.

If the headphones are not turned on after this procedure:

• 🔌 Try another charging cable (original from Xiaomi or with Quick Charge support).
• 🔋 Allow headphones to charge in the case for at least 1 hour.
• 📧 Contact Haylou support (attach video problems) – they can send firmware for manual recovery.

⚠️ Attention: Forced case reset erases all pairing data and resets the firmware to the factory version. If the headphones are unstable after that, update the software through the Haylou Fun app.

Method 4: Reset one headphone (if synchronization is lost)

A common problem with the Haylou GT1 is that one headphone connects to the phone and the other is silent or defined as a separate device, which is due to a synchronization failure between the right and left modules, in which case you only need to reset the problem earphone without affecting the work unit.

How to Reset One Headphone:

1. Turn off both headphones (hold the touchpad for 5-7 seconds).
2. Put the working headphone in the case and close the lid.
3. Hold the touchpad on the problem earphone for 15 seconds until you hear a double beep.
4. Take the working headphone out of the case – they should automatically synchronize (indicators blink white).

If the synchronization is not restored:

• 🔄 Reset both headphones (method 1) and repeat pairing.
• 📱 In Bluetooth phone settings, remove all devices called Haylou GT1 or LE-GT1.
• 🔋 Charge the case to 100% – sometimes low charge interferes with synchronization.

In rare cases, the loss of synchronization is due to a hardware malfunction of the antenna in one of the headphones. If after reset the problem remains, check the work of each headphone separately (plug only the right or only the left to the phone).

Method 5: Reset via the Engineering Menu (for advanced users)

If standard methods don't work, you can try resetting your headphones through the engineering menu available on some firmware versions, which requires an Android smartphone with ADB support and a bit of technical knowledge.

Step-by-step:

1. Install the nRF Connect app (for Android) on your phone.
2. Connect the GT1 headphones via Bluetooth.
3. In the application, find the service with UUID 0000ffe0-0000-1000-8000-00805f9b34fb.
4. Send the AT+RESET command through the input field (without quotes).
5. The headphones should reboot and reset to factory settings.

Warnings:

• 🚨 The wrong command can put the headphones out of order.
• 📵 The method does not work on all versions of the firmware.
• 🔧 Developer rights are required on the phone.

If you are not sure about your actions, it is better to contact the service center, which is only relevant for users who have previously worked with the service center. ADB or BLE-protocol.

💡

Before using the engineering menu, back up your Bluetooth settings on your phone. In rare cases, the reset command can affect other connected devices.

Table: Comparison of Haylou GT1 resetting methods

Frequent Resetting Mistakes and How to Avoid Them

Even when following instructions, users often make mistakes that prevent successful resets.

1. Incomplete headphone discharge. If the charge level is below 10%, the reset may be interrupted. Always check the charge indicator before the procedure.
2. Interrupt. If you release the buttons before the beep, the reset will not occur. Hold the panels for at least 15 seconds.
3. Use a non-original case, cheap substitutes don't have to pass the reset command to the headphones, use only the native case.
4. Ignoring the sound. Double squeaking is a confirmation of a successful reset. If you didn't, repeat the procedure.

Another common problem is that when you reset, the headphones connect to the phone, but the sound is only in one, which means that the synchronization between the right and left modules is not restored.

• 🔄 Turn off both headphones, put them in the case for 1 minute, then pull out and turn on.
• 📱 In Bluetooth phone settings, forget the device and connect again.
• 🔋 Check if one of the headphones is discharged (the indicator on the case should burn green for both).

⚠️ Note: If after reset, the headphones are defined as two separate devices (Haylou) GT1_L Haylou GT1_R), This is a sign of a firmware failure. Update the software through the Haylou Fun app or contact the service.

💡

If the reset didn't work the first time, repeat the procedure by holding the buttons 5 seconds longer, and 60 percent of the time, the problem is solved on the second try.

FAQ: Answers to Frequent Questions About Haylou GT1 Reset