How to properly turn on Xiaomi Mi TV P1: all ways and solutions to problems

Xiaomi Mi TVs TV P1 The technology has become a popular choice thanks to a combination of modern technology and affordable prices, but even with such a technique, users sometimes have questions about basic control - for example, how to turn on the device correctly after buying, moving or long downtime. In this article, we will analyze all possible scenarios: from standard launch to solving emergency situations when the TV does not respond to the remote or buttons.

It is important to understand that the process of inclusion may vary depending on the firmware version, the year of release of the model (for example, Mi). TV P1 2021 vs Mi TV P1 2023) and even from the delivery region, and we've taken all the nuances into account and prepared a universal guide that will help both beginners and experienced users, if your TV suddenly stops turning on, do not panic: in 90% of cases, the problem is solved without going to the service center.

Preparation for the first inclusion: what to check

Before you press the power button, make sure that all the prerequisites are met. This will save you from unnecessary manipulation and possible errors.

First, check the kit. In the box with Xiaomi Mi. TV P1 must:

• 📺 The TV itself with a protective film on the screen
• 🎛 Remote control (usually with batteries)
• ⚡ Power cable (sometimes included, sometimes purchased separately)
• 📄 Guarantee card and brief instructions
• 🔧 Wall mounted fixtures (if provided)

Pay special attention to the power cable. TV P1 The connector can be either standard (like a "chip") or non-removable with a direct connection to the power supply. If the cable is missing, use the original from Xiaomi or a certified analog with parameters. 220V/50Hz and with a power of no less 150W.

⚠️ Warning: Never use cables from other household appliances (e.g. computer monitors or microwaves) that mismatch voltage or current can damage the TV's power supply.

Second, choose the right place to install. Make sure that:

• 🔌 The socket is available and not overloaded with other devices
• 🌡 Temperature in the room from +5°C +35°C
• 💧 Humidity does not exceed 80% (especially important for bathrooms)
• 📶 There are no strong sources of electromagnetic interference near (routers, microwaves)

Standard Enablement with a DU Remote

The most common way to do this is to use a remote control, and even if you've never used Xiaomi technology, it's intuitive.

1. Connect the power cable to the TV and the socket.

2. Press the red Power button on the remote (usually located in the upper left corner).

3. wait for the system to boot (the Mi logo will appear on the screen). TV).

4. Follow the instructions on the screen for initial setup.

If the TV does not respond to the remote, check the checklist:

The Mi models TV P1 The remote can operate on both infrared (IR) and Bluetooth (newer versions). If the IR receiver is locked (for example, with a decorative panel), try using the remote in Bluetooth mode:

1. Press and hold the Menu buttons. + OK 5 seconds at a time.
2. Wait for the LED to blink on the remote (blue indicates Bluetooth mode).
3. Repeat the switching attempt.

💡

If the remote is lost, you can temporarily use the Mi Remote app on your smartphone (available for Android and iOS), and both devices must be connected to the same Wi-Fi network.

Alternative ways to include without remote control

Situations where the remote is lost, the batteries are broken or discharged are not uncommon. TV P1 There are several alternative methods of inclusion:

Power button on the body

On the back or side of the TV (usually under the Mi logo) is a mechanical button.

• 🔘 Touch (press and hold for 3 seconds)
• 🔘 Mechanical (click once)
• 🔘 Combined (sensor) + lighting)

On the Mi models TV P1 The 55" and 65" buttons are often hidden under a small plastic stub. Carefully tuck it in with a nail or plastic card.

Voice control

If your TV supports Google Assistant or Alice from Yandex, you can turn it on with your voice:

Okay, Google, turn on Mi TV.

For this:

• Make sure the TV is connected to Wi-Fi
• Voice assistant activated in settings
• The microphone on the remote or on the TV is not silenced.

3. Through the mobile application

The Mi Home app allows you to control your TV remotely if it's connected to your Xiaomi account.

1. Open Mi Home and select your TV from the device list.
2. Click on the power icon in the upper right corner.
3. Confirm the action if necessary.

⚠️ Note: If the TV is completely drained (for example, after a long storage period), none of these methods will work. 10-15 minutes to charge the internal condenser.

What to do if the TV is not turned on: diagnosis of problems

If Xiaomi Mi TV P1 It doesn't respond to the remote or the button on the body, so we're going to start with the simplest and most obvious reasons:

Pay special attention to the nutrition indicator, and its behavior is key to diagnosis.

• 🔴 It's always burning red. → The TV is on standby, but not responding to commands. Try pressing the power button for 10 seconds for a forced reboot.
• 🟢 Green is burning. → System loaded, but possibly damaged HDMI-port or cable (check connection to the signal source).
• 🔴➡🟢 It flashes red, then green. → Update the firmware. Don't turn off power at this point, it'll make the device "brick.

If the TV was working normally before, but stopped turning on after the upgrade, try resetting the firmware to the factory version.

1. Turn off the TV.
2. Press and hold the Volume button (volume decrease) on the body.
3. Without releasing the button, connect the power cable.
4. Hold the button still. 10-15 A few seconds before the recovery menu appears.

Incorporation after prolonged downtime or transportation

If the TV hasn’t turned on for several months (for example, after buying a “future” or moving), follow a special algorithm:

1. Check the storage conditions:

- Temperature should have been in range -20°C...+45°C.

Humidity not higher than 85% (condensation inside the housing can cause a circuit).

2.Let the TV acclimatize:

- If the device is stored in a cold room, wait. 2-3 pre-insertion.

- If it came from the cold — 4-6 hours.

Check the capacitors:

After a long period of idleness, electrolytic capacitors may lose capacity.

- At the first turn on, cotton from the speakers is possible - this is normal.

Update the firmware:

During the downtime, new versions of the software with error corrections could be released.

- Go to Settings. → On TV. → Updating the system.

⚠️ Warning: If the TV is stored in a wet room (such as a garage or basement), dry it in a warm dry place for at least 24 hours before turning on. Using a hair dryer or heater will speed up the process, but keep the device at least 50 cm away from the heat source.

For Mi models TV P1 s OLED-screens (e.g., Mi) TV P1 OLED) After a long downtime, it is recommended to start compensation for the charge of pixels:

1. Turn on the TV.
2. Go to Settings. → Screen. → Additional settings → Compensation OLED.
3. Start the process (takes about a few minutes). 30-60 minute).

This will prevent pixel burnout and extend the life of the screen.

Features of inclusion after updating the firmware

Updates to the firmware on Xiaomi Mi TV P1 They usually go automatically, but sometimes they require manual intervention. If the TV doesn't turn on or is unstable after the upgrade, follow these steps:

1. Forced reset

Press and hold the power button on the remote (or case) for a period of time. 15-20 This will reset the system cache and restart the Android kernel. TV.

2. Reset to factory settings

If the TV is turned on but is running with errors (for example, constantly restarting or apps are not opening), reset:

Settings → Device → Reset → Erase all data

The process will take 5-10 After the reset, you will need to reset the Wi-Fi and Google account.

3. Firmware rollback (for experienced users)

If the new version of the software causes critical errors, you can go back to the previous one.

• Download the desired firmware version from the official Xiaomi website (support section).
• Unpack the archive and copy the update.zip file to the flash drive (FAT32 format).
• Put the flash drive in. USB-television-port.
• From the recovery menu, select Apply update from USB.

💡

Before rolling back the firmware, back up the data through Settings → The device → Backup: This will save the list of applications and some settings, but does not guarantee the safety of personal data.

If the TV is stuck in the refresh phase (the indicator is on, but the process does not end for more than 30 minutes), try:

1. Shut down the power for 10 seconds.
2. Turn on the TV again – the system should resume the update.
3. If it doesn’t help, reset through the recovery menu (see section above).

Power management: energy saving settings

Xiaomi Mi TV P1 It's equipped with several power modes that affect the power on process:

Settings → Device → Energy saving

Let’s look at the main options:

For the fastest possible turn on, we recommend leaving the "Quick Start" mode, but keep in mind that in this case the TV will consume about 0.5-1 Wh/hour, even when you're off. If you don't like it, choose Eco Mode or Deep Sleep.

Also, pay attention to setting up Automatic Shutdown through HDMI-CEC. If this function is active, the TV can be turned on/off along with connected devices (e.g., a set-top box or sound bar:

Settings → Device → HDMI-CEC

💡

If the TV turns on by itself at night, check the timer settings in Settings → System system → On/off timer. The "Wake Up for Updates" function may have accidentally activated".

FAQ: Frequent questions about including Xiaomi Mi TV P1