When your Xiaomi stops responding to presses, it can be taken by surprise at the most inopportune moment.Whether it’s a Redmi series smartphone or a modern Android TV, the lack of reaction to the power button often causes panic in the user.However, in most cases, the device is not broken, but simply went into deep sleep or faced a software failure.
Understanding how to turn Xiaomi on correctly will help avoid unnecessary trips to the service center. Modern gadgets are equipped with a sophisticated battery protection system and software controllers that can block standard startup methods. In this article, we will discuss all possible scenarios, from banal discharge to the need for flashing.
Standard algorithm for enabling a serviceable device
For most users, the startup process is obvious, but there are nuances that even experienced tech owners forget: If you just bought a new smartphone or TV, the first thing to do is provide power. The lithium polymer batteries used in Mi and Redmi often come from the factory with minimal charge for long-term storage.
Connect the device to the original charger and wait at least 10-15 minutes. Even if the screen is not showing anything, the chemical processes inside the battery are already running. After that, press the power button. On smartphones, it is usually located on the right side, and on TV remotes - at the top or on the side.
It's important to distinguish between short and long press. A short click usually wakes up the screen or shows notifications, whereas holding the button for 3-5 seconds initiates the operating system to boot. If the indicator blinks and goes out, but the screen remains black, perhaps the problem lies in the software.
- 🔌 Make sure the cable is USB snugly inserted into the connector until a characteristic click.
- ⏱️ Hold the power button for at least 5 seconds to start the system.
- 🔋 When you first turn on after purchase, leave your phone on charge for 30 minutes.
💡
Use only certified cables and power supplies. Cheap analogues can give low current, which will cause the phone to show charging, but will not turn on.
What to do if the Xiaomi smartphone does not turn on
The most common reason for failure is a Soft Brick. The screen goes out, the backlight doesn't light up, but the device actually works using energy, and then you can't shut down the standard shutdown, and you'll have to do a forced reboot procedure that emulates battery extraction.
Xiaomi and Redmi have the same algorithm for most models, and you need to press two buttons at the same time: Volume up and Power. Keep them clamped around. 10-15 If it goes well, you'll feel a little vibration, and the Mi logo or Android logo will appear on the screen.
⚠️ Warning: If you have a menu with English text (Main Menu, Recovery) on your screen after the button combination, you are in recovery mode. Don't worry, this is a regular situation. To exit, select Reboot and then Reboot to System using volume buttons for navigation and power button for confirmation.
Sometimes the massage therapist method helps. Hold the power button and, without letting go, intensely but without fanaticism, press your finger on the camera area or the logo on the back cover, which can restore contact between the plume or battery if the problem is the physical withdrawal of contacts.
☑️ Smartphone diagnostics
Inclusion of Xiaomi Mi TV and consoles
Smart TVs Mi TV and Mi Box have their own specifics of launch. Often users confuse standby with full shutdown. If the screen is black and the indicator is on red, the device is in Standby mode. To turn on, you need to press the power button on the remote or on the TV body.
If the TV doesn't respond to the remote, check the batteries and try to start the system with a button on the housing itself (usually hidden behind or below, sometimes combined with a control joystick). If this does not help, try to disconnect the TV completely from the network by pulling the plug from the socket for 1-2 minutes.
The Mi Box S is a problem with the HDMI-The TV can be turned on, but the image doesn't show up because of poor contact. Try switching the signal source (Input) on the TV remote or reconnecting the cable. HDMI.
| The device | Positioning of the button | Indication | Hover-flying action |
|---|---|---|---|
| Mi Smart TV | Downstairs or joystick | Red/White | Shut off the network for 2 minutes |
| Redmi TV | Under the logo or behind | Red/Orange | Press the power button 10 seconds |
| Mi Box S | On the hull (round) | Blinks when loading | Remove from HDMI and sockets |
Remember that updating your TV firmware can take a long time. If you see the Android TV logo and download scale, do not turn off the power, even if the process seems to be stalled.
Recovery and Fastboot Modes: When You Need Them
If standard methods didn’t help, the bootloader or system files may have been damaged, in which case the device can only be turned on in special modes. Recovery Mode is a recovery environment that allows you to reset to factory settings or install a new firmware.
To enter this mode on the phone turned off, press Volume Up and Power. Fastboot is a low-level access mode used by engineers and advanced users to run through the PC. Entry is done by clamping Volume Down and Power.
What is the danger of Fastboot?
Being in these modes doesn't mean that the iron is broken. Often the phone gets there because of a bug when updating or sticking buttons. If you happen to be on a menu with a picture of a rabbit fixing an android (Fastboot), just press the power button for 10-15 seconds until the device vibrates and turns off.
- 🐰 The logo of the hare means Fastboot mode (low-level firmware).
- ⚙️ A menu with a few items is a recovery).
- 🔄 To exit both modes is usually enough long power retention.
Problems with battery and charging
Deep discharge is the insidious enemy of modern electronics. If Xiaomi has been dead for months, battery voltage has dropped below a critical threshold, in which the power controller blocks charging for safety reasons, and the phone shows no signs of life.
To “swing” the battery, leave the phone on charge in a state of switching off for at least 2-3 hours, preferably overnight. Sometimes you need to use a charger with lower current (for example, from a USB 2.0 computer) to start the chemical reaction slowly and safely.
⚠️ Warning: Do not try to charge a ballooning battery. If the back of the phone is raised or the body is deformed, using the device is dangerous and can lead to fire.
Also check the charging connector. It is often clogged with pile and dust in your pockets, which prevents contact. Clean the port carefully with a toothpick or soft brush. The use of metal objects is strictly prohibited, as you can close contacts.
💡
If the phone lies idle for more than 3 months, once every six months it should be put on charging to save the life of the battery.
When a service center is needed
There are situations where software methods are powerless, and if after all the manipulations, including changing the cable, the socket and the long wait, the charging indicator does not light up, there is a possible hardware malfunction, it could be a failure of the power controller, the plume or the battery itself.
A particularly alarming symptom is the smell of burning or the underside heating when you try to charge, in which case immediately disconnect the device from the network, further attempts to turn on may short circuit and damage the motherboard.
Also, the help of specialists is needed if the phone turns on, but the screen remains black (while you hear the sounds of the system or vibration works), this indicates a malfunction of the display module or screen plume, which requires disassembling and replacing components.