Why the remote does not work with Xiaomi TV and how to fix it
You plugged Rostelecom into a Xiaomi TV, but the remote doesn't control volume, turn on or switch channels? The problem is typical: manufacturers use different infrared control protocols, and universal codes don't always work the first time. 80% of the time, the solution takes no more than 5 minutes - you just need to sync the devices correctly.
In this article, you will find 3 working ways to bind the remote (including hidden codes for Xiaomi Mi TV 4S/4A/5), a table of model compatibility, and instructions for correcting common errors - from flashing the indicator to completely ignoring commands. If your TV is released after 2020, look at the section on HDMI-CEC - this is the most reliable method for new devices.
Before you start setting up, make sure that:
- 🔋 Batteries in the remote are fresh (even if the indicator is on fire - replace them with new Duracell or Energizer).
- 📺 The TV and console are connected to one outlet through a network filter (voltage surges knock down the settings).
- 🔄 There are no physical damages on the remote (cracks on the IR emitter are a common cause of malfunctions).
Method 1: Automatic setting of the remote by Rostelecom
The simplest method, which works for 60% of users, is suitable for Rostelecom’s STB-100/200/300 remotes and Xiaomi’s Android TVs (including Mi TV 4S 2020+).
Algorithm of action:
- Turn on the TV and console, wait for the interface to load.
- On the Rostelecom remote, press the OK + TV buttons simultaneously for 5 seconds until the indicator starts flashing twice.
- Point the remote to the TV (range 20-30 cm) and press 1 (code for Xiaomi).
- Wait 10 seconds – if the indicator is gone, the synchronization was successful.
If the TV doesn't respond:
- 🔄 Repeat the procedure, but in step 3 press the buttons from 0 to 9 in turn (each corresponds to a unique manufacturer code).
- 📱 Check if the IR signal is blocking the glass or the protective film on the remote control.
☑️ Preparation for manual adjustment
Method 2: Manual code entry for Xiaomi TV
If the automatic setup didn't work, try entering the codes manually. For Xiaomi TVs, the following combinations are suitable:
| Model TV set | Code 1 | Code 2 | Code 3 |
|---|---|---|---|
| Mi TV 4S (2018-2022) | 1245 | 0178 | 1004 |
| Mi TV 4A (32-43 inches) | 0021 | 1176 | 0124 |
| Mi TV 5 / 5 Pro | 1009 | 0001 | 1256 |
| Mi TV Q1/Q2 (QLED) | 0004 | 1010 | 1187 |
Instructions for entry:
- Press TV + OK for 5 seconds (the indicator blinks once).
- Enter the first code from the table (e.g. 1245 for Mi TV 4S).
- Click OK – if the indicator is gone, the code is accepted.
- Check the work of the buttons Vol+/Off and On/Off.
⚠️ Warning: If after entering the code, the TV stopped responding to the native Xiaomi remote, reset: pinch Menu + Volt+ That'll bring back the factory settings of the IR receiver.
What if no code fits?
Method 3: Control via HDMI-CEC (for TVs 2020+)
HDMI-CEC technology allows you to control the console Rostelecom through the native Xiaomi remote (and vice versa), which is the most reliable method for new models, as it does not depend on infrared signals.
Adjustment steps:
- Connect the set-top box to the TV via the HDMI 1 (ARC) port (recommended) or any other HDMI.
- On the Xiaomi remote go to Settings → Devices and accessories → HDMI-CEC.
- Enable the Control option HDMI-devices (or AnyNet)+, If the TV is older than 2019).
- On the console Rostelecom in the menu, find Settings → Devices → HDMI-CEC and activate the function.
After synchronization:
- 🎮 Xiaomi remote will switch channels on the console.
- 🔊 Volume buttons on the remote Rostelecom will regulate the sound of the TV.
- ⚡ Simultaneous pressing on/off on any remote will turn both devices on/off.
⚠️ Note: If after connection, the console is not displayed in the list HDMI-Check the TV, check the cable. HDMI — Must support version 2.0 or higher (old cables do not transmit) CEC-The port is on the TV — HDMI 1 (ARC) priority CEC.
💡
If the Xiaomi TV doesn’t see the console through HDMI-CEC, try disconnecting both devices from the network for 1 minute, then turning on the TV first, and then the console.
Problem Solving: The remote is not synchronized
If none of these methods worked, check for common errors:
| Problem. | Possible cause | Decision |
|---|---|---|
| The monitor on the remote is flashing, but the TV is not responding. | Incompatibility of IR protocols | Try out the codes for Sony (0000, 1111) – some Xiaomi models support them. |
| The remote controls only the console, not the TV | TV mode is off on the remote. | Press the TV for 3 seconds, then reset. |
| Volume buttons work, but don't switch channels | Wrong code for the console model | Reset the remote (press TV + OK for 10 seconds) and re-enter the code. |
| The TV is turned on, but immediately turned off. | Conflict of teams with native Xiaomi remote | Turn off the Quick Start feature in the TV settings. |
Critical note: On Xiaomi Mi TV P1 (2021), Rostelecom’s factory codes do not work due to hardware limitations.The only solution is to use HDMI-CEC or buy a universal learning-enabled remote (for example, the BroadLink RM4 Pro).
💡
If your TV is released before 2018, it probably doesn’t support HDMI-CEC, so you can only manually enter codes or buy a new remote.
Alternative management practices
If standard methods don’t help, consider these options:
1. Rostelecom TV application for smartphone
- 📱 Install the application on Android or iOS.
- 🔗 Connect to the same Wi-Fi network as the console.
- 🎯 Use your smartphone as a remote – all features including voice search are supported.
2. Universal remotes with training
- 🛒 Suitable models: Xiaomi Mi Remote (requires firmware), One For All URC 7940.
- 🔄 Learning algorithm: point both remotes at each other and consistently press buttons to copy signals.
Voice control
- 🎤 If you have a Xiaomi Mi TV Google Assistant: OK Google, turn on Rostelecom".
- 🔊 For the Rostelecom consoles 4K voice search is available on the button Microphone on the remote.