Tune-in TV channels TV-Xiaomi: from auto search to manual settings

Xiaomi TV is not only access to streaming services, but also the ability to watch on-air, cable or satellite TV. However, many users face difficulties in the first setup of channels: the console does not find broadcasts, the signal is constantly interrupted, or the list of channels is displayed in a chaotic order. In this article, we will analyze all the ways of setting up, from automatic search to manually adding frequencies, and also tell you how to avoid typical errors.

If you've just connected a Mi TV Box, a Mi Box S, or some other model, don't rush to call the wizard. Most of the problems are solved through the console menu, and the setup process takes no more than 10-15 minutes. The main thing is to choose the right signal source (antenna, cable, satellite) and follow the step-by-step instructions. We'll also focus on hidden settings that the manufacturer does not advertise, but which can significantly improve the quality of reception.

In the article you will find:

• 🔍 Step-by-step algorithm for auto-search channels for different signal sources
• ⚙️ Manual addition and sorting of TV channels (including hidden ones)
• 📡 Solving problems with weak signal or lack of channels
• 🔄 Update the channel list after changes to the provider
• 🛠️ Reset TV tuner settings without losing application data

1. Preparation of Xiaomi console to configure channels

Before you start searching for channels, make sure that Xiaomi is properly connected to the signal source, which depends on whether the system finds at least one channel or produces an error No signal.

Here's what you need to check:

• 📶 Antenna or cable: if you use terrestrial TV, the antenna must be connected to the connector RF IN For cable, cable is the same cable from the provider — LNB IN (if the model supports).
• 🔌 Nutrition and HDMI: The box must be placed in the socket and HDMI-cable connected to the TV (port) HDMI 1/ARC preferably).
• 🌐 Internet: although it is not necessary to set up air channels, some Xiaomi models (for example, Mi) TV Box 4S Pro) require a network connection to download broadcast data.

Pay special attention to the cable from the provider, if it is damaged or poorly fixed in the connector, the signal will be intermittent, and also check if there is a filter or amplifier on the cable, which sometimes block some frequencies.

⚠️ Note: If you connect Xiaomi to an old TV without HDMI, use the adapter HDMI → AV (RCA). However, in this case, the setting of channels through the console menu may not be available – you will need an external TV tuner.

After checking the connections, go to the main console menu.

1. Turn on the TV and select the HDMI signal source (corresponding to the port to which the console is connected).
2. On the Xiaomi remote, press the Home button.
3. Go to the Settings section (cog in the upper right corner).

2. Selection of signal source: on-air, cable or satellite TV

Xiaomi consoles support three types of broadcast, and the right choice depends on the success of the configuration.

To select the source of the signal in the console:

1. In the Settings menu, go to the TV antenna or TV (name depends on the model).
2. Select Signal Type:

Search engine

Important: The Mi Box S and Mi TV Stick do not support satellite TV (DVB-S2), and will require a separate receiver or model Xiaomi Mi TV Box Pro with the appropriate connector.

3. Automatic channel search: step-by-step instructions

Autosearch is the easiest way to set up channels. Xiaomi will scan the available frequencies and save the broadcasts found.

• 📶 The antenna or cable is properly connected;
• 🔋 The console is on the network (do not discharge it while searching);
• 📡 No interference (e.g., a microwave operating near the antenna).

Instructions for search:

1. Go to Settings → TV antenna → Auto search.
2. Select Signal Type (e.g. DVB-T2 for terrestrial TV).
3. Press Start and wait until the scan is completed (may take 5-10 minutes).
4. After you search, the console will show you a list of channels found.

If the search engine did not find any channels:

• Check if the signal amplifier on the antenna is on (if any).
• Try changing Search Mode from Full to Quick (or vice versa).
• Update the firmware of the console: Settings → About the console → Update the system.

⚠️ Note: Some Xiaomi models (e.g. Mi Box 3) may display no-name channels after autosearch (e.g. Service 1, Service 2.

4. Manual addition and sorting of channels

If the search engine fails or you need to add a specific channel (e.g. regional), use manual tuning.

• 📻 The console does not find some channels (for example, TNT or REN TV);
• 🔢 You need to change the order of the channels in the list;
• 🔍 You need to add a hidden channel (for example, test or paid channel).

How to add a channel manually:

1. Go to Settings → TV antenna → Manual search.
2. Select the signal type (e.g. DVB-T2).
3. Enter the parameters: Frequency (e.g. 546 MHz for Channel One in Moscow); Modulation (typically 256 QAM for cable TV or COFDM for on-air); Transmission rate (e.g. 6875 ks/s).

Search

Where to get the parameters for manual search?

• 📡 For terrestrial TV: frequencies can be found on the RTRS website (enter your region).
• 📺 For cable TV: check with the provider (for example, Rostelecom or MTS).
• 🛰️ For satellite TV: parameters depend on the satellite (for example, Yamal 402 or the satellite). ABS-2).

To sort the channels:

1. Go to Settings → TV antenna → Channel management.
2. Select a channel and click Change Order (or drag it to the right place).
3. To remove unnecessary channels, click Remove.

5. Solving Signal and Channel Problems

If the channels are found, but the image is slowing down, the sound is interrupted or the quality is poor, the problem may be in the signal or settings of the console.

If Xiaomi doesn’t find channels after the update, the tuner settings may have gone wrong.

1. Go to Settings → TV antenna → Reset settings.
2. Confirm the reset (this won't remove apps, just TV settings).
3. Run the search again.

The problem with regional channels? Sometimes the console finds channels from another city.

• In manual mode, remove unnecessary channels.
• In the antenna settings, select Region (if you have such an option).
• Update the list of channels via the Internet (if the model supports).

💡

If Xiaomi constantly “forgets” channels after turning off, turn off the Power Saving feature in the power settings. This will help avoid resetting temporary data.

6. Update the channel list after changes to the provider

Cable or satellite providers periodically change frequencies, add or remove channels, and if you notice that some broadcasts are missing or new ones have appeared, you need to update the list.

Refreshment methods:

1. Quick Update: Go to Settings → TV antenna → Update channels. Select Quick Scan (the console will only check current frequencies).
2. Complete search: Run AutoSearch again (as described in Section 3) This will take longer, but will ensure that all available channels are discovered.

Manual appendix:

• If you know that the provider has added a new channel at a specific frequency, enter it manually (section 4).

If some channels are not working after the update, check:

• 🔄 Has the provider changed the subscription package (the channel may have become paid).
• 📡 Has the signal deteriorated (check the antenna/cable connection).
• 🔧 Does the update of the console firmware not need to be updated.