Modern wireless headphones, such as the Xiaomi Earphones 2 Basic, are complex miniature computers that require periodic software intervention. Owners often face situations where the device stops synchronizing correctly with the smartphone or begins to make extraneous noises. In such cases, a standard power outage does not help, and the only right solution is a complete reset configuration.
The factory reset process eliminates software errors that accumulate in the headset’s memory during operation, which returns the headphones to the “out of the box” state by removing all temporary files and old pairing profiles. Forced reset often solves 90% of connection problems without having to go to a service center.
In this article, we will take a detailed look at the Earphones 2 Basic, look at common errors and answer frequently asked questions. It is important to understand that the procedure requires accuracy and consistency, as improper execution of steps can lead to the fact that the headphones will not enter the flashing mode.
Signs of the need to reset headphones Xiaomi
The first and most obvious sign is that you can't connect to your smartphone even if the Bluetooth on your phone is active and you can see other devices. Headphones can show up on the list of available ones, but when you try to connect, you can either make a mistake or just keep quiet.
Another alarming signal is channel desynchronization, where the sound is played in only one earpiece or with a noticeable delay between the left and right channels, especially when watching videos when the movement of the actor’s lips does not match the spoken phrase, and users may notice that the indicators behave strangely: flashing in the wrong color or do not respond to touch.
If you see the following, it is time to reset:
- 🔴 The indicator burns red or flashes in an incomprehensible way, ignoring charging.
- 🔊 The sound became quiet, hoarse or disappeared in one of the speakers.
- 📱 Smartphone “sees” headphones, but refuses to create a pair.
- 🔋 Battery charge is consumed abnormally quickly, although this has not been observed before.
⚠️ Warning: If the headphones are completely discharged, they may not respond to reset commands. Before starting the procedure, make sure that the case and the headphones themselves are charged at least on the headphone. 20-30%.
Ignoring these symptoms can lead to a software failure fixing itself in the device’s memory. A timely reset helps avoid more serious problems with the Bluetooth controller’s firmware. Don’t wait for a complete failure, it’s better to update the configuration prophylactically at the first sign of instability.
Preparation for the configuration reset procedure
Before you get into action, you need to properly prepare the workplace and the devices themselves. Chaotic button presses without understanding the current status of the headset can confuse the system even more. The first step should always be to clean the list of associated devices on your smartphone or tablet.
Go to your mobile device's Bluetooth settings, search the Xiaomi Earphones 2 Basic list, and select "Forget Device" or "Unpair" option, which is a critical step, as it removes the stored encryption key on the phone side, and if you don't, the phone will try to connect to old, no longer relevant options.
Next, check the status of the charging case, make sure that the contacts inside the case are clean and free of dust or pile from clothing, dirty contacts can prevent the correct transmission of control signals, which may not activate the reset mode, wipe the contacts with dry soft cloth or cotton swab if necessary.
☑️ Preparation for discharge
Once you clear the pairing list, turn off Bluetooth on your smartphone, which will prevent automatic reconnection during the reset process, which could interrupt the procedure, and now your headphones and phone are ready for maintenance.
The main method of resetting through touch panels
The most common way to bring Xiaomi Earphones 2 Basic back to factory settings involves using touch zones on the headphones themselves. This method requires no special application and works at the level of a hardware controller. The main condition for success is synchronization of actions and accurate observance of time intervals.
Remove both earbuds from the charge case. Make sure they're on (normally the lights flash). Now you need to touch the touch areas on both earbuds at the same time. Depending on the firmware version, you need to hold your fingers for 5 to 10 seconds until the lights change color or blink frequency.
The Earphones 2 Basic model is characterized by the following sequence:
- 👆 Touch the sensory area of the left earphone.
- 👆 At the same time, touch the sensory area of the right earphone.
- ⏱ Hold the touch for about 5 seconds until the reset indication appears.
- 🔄 Wait until the indicators go out or light up in red/white.
When you successfully reset, the indicators can blink a few times or change the color of the glow. This is a signal that the configuration memory is cleared. After that, put the headphones back in the case, close the lid and wait 10-15 seconds. Then open the case again - the headphones should go to the device search mode (quick flashing of the white indicator).
⚠️ Warning: Don't unclutch your fingers early. If you release the touchpad at 4 seconds, the headphones can just turn off, not reset. Hold until the characteristic display changes.
If you don't get it the first time, don't despair. Sometimes it takes a few tries to catch the right timing moment, and the key is to act confidently and press both earbuds at the same time.
Alternative method of discharge through charging case
In some versions of the Xiaomi Earphones 2 Basic or in certain software errors, the touch panel method may not work, in which case manufacturers have provided an alternative path through the buttons or contacts of the charging case, a method often called “deep reset” because it affects lower levels of power management.
Put both earbuds in the charge case, but don't close the lid right away. Make sure they're on charge (the headphones are on fire). Now find the function button on the case. On the Basic model, it may not be there, then the button is the touch zone or long-term retention in the case.
If there is a button on your case:
- Put the headphones in the case.
- Press and hold the button on the case for 10-15 seconds.
- Watch the indicator on the case: it should flash white or red.
- Release the button only after changing the indication.
If there's no button on the case, try holding the headphone touchpads while they're inside the case. This is a rare but possible scenario for some batches. In any case, the key is the light indicator response. Light indication is the only language in which the device communicates its internal processes.