How to connect wireless headphones to a Xiaomi TV: a step-by-step guide

Wireless headphones have become an integral part of modern movie and TV viewing – they allow you to enjoy the sound without interference to others, especially at night or in families with young children. TV, Redmi TV, Mi TV A et al.) is a frequent questioner. Unlike smartphones, where the pairing process is intuitive, TVs have their own nuances, from hidden settings to firmware version restrictions.

In this article, we will discuss all possible ways of connecting – from standard Bluetooth connection to alternative methods using adapters and other devices. TV-We'll focus on the typical problems of latency, spontaneous shutdowns, and the lack of Bluetooth on the menu. If your Xiaomi TV doesn't see headphones or the sound is interrupted, here you'll find working solutions with explanations for the 2018-2026 models.

1. Compatibility Check: Does your TV support Xiaomi Bluetooth?

Before you try to plug in your headphones, make sure your Xiaomi is ready. TV It's actually equipped with a Bluetooth module. This is critical, because budget models like Redmi are very low-end. TV A55 or Mi TV 4S 32" is often released without it. Here's how to check:

• 📄 Documentation: Find a box or instruction manual for the TV – it should have Bluetooth protocol (e.g. Bluetooth 4.2 or 5.0).
• 🔍 Settings menu: Go to Settings → Devices → Bluetooth. If there's no partition, there's no module.
• 🌐 Enter the TV model on mi.com and check the specs.

Important: Xiaomi TVs based on Android TV (Like Mi. TV Q1/Q2) Bluetooth is always supported, and PatchWall models are always supported. TV 4X, 4A) — Only in versions with the prefix Pro or Max.

⚠️ Note: If your TV doesn’t support Bluetooth, but has a port USB 3.5 mm, you can use an external Bluetooth adapter (we will talk about it in section 4).

2. Standard Bluetooth connection: step-by-step instructions

If you're Xiaomi. TV It's Bluetooth-enabled, follow this instruction, and it can vary slightly depending on the PatchWall version or Android version. TV, But the general logic holds.

Steps for PatchWall (Mi) TV 4A, 4X, Redmi TV):

1. Turn the headphones on in pairing mode (usually hold the power button for 3-5 seconds until the indicator blinks).
2. On the Xiaomi remote, press the Settings button.
3. Go to Settings → Devices → Bluetooth.
4. Activate the Bluetooth slider and wait for the headphones to appear in the list.
5. Select your headset and confirm the connection.

Steps for Android TV (Mi TV Q1/Q2, Mi TV A):

1. Open the Settings. → Devices → Bluetooth and other devices.
2. Click Add Device and select Audio Device Type.
3. When you find the headphones, press them and wait for the pairing.

The pairing mode on the headphones is enabled

TV and headphones charged (>30%)

Distance between devices < 1 meter

Other Bluetooth devices (smartphone, smart watch) are disabled)-->

If the headphones don’t appear in the list, try:

• 🔄 Restart the TV (Settings) → On TV. → Reboot).
• 📱 Remove headphones from the memory of other devices (they can stick on the old connection).
• 🔋 Check the charge of headphones - some models (AirPods, Sony) WH-1000XM4) Not visible at low battery levels.

💡

If the TV “sees” the headphones but doesn’t connect, try resetting Bluetooth settings: go to Settings → Devices → Bluetooth → Three dots (menu) → Reset the settings.

3. Problem solving: sound delay, communication interruptions, lack of sound

Even after a successful connection, users often face three main problems: audio lag, communication interruptions, and the lack of sound in the headphones. Let's take each one apart.

Sound delay (latency)

The reason for the delay is Bluetooth codecs.Most Xiaomi TVs use SBC — It's universal, but not optimized for video codec:

• 🎧 Use headphones with low-latency aptX support or AAC (Like Sony. WH-1000XM5, Bose QuietComfort 45).
• 📺 Update the TV firmware: Settings → On TV. → Updating the system.
• 🔊 In the audio settings, select Bluetooth audio → Low latency (if there is an option).

Communications interruption

If the sound is interrupted or the headphones are turned off, check:

• 📶 Interference: Remove other Bluetooth devices (smartphone, keyboard) or Wi-Fi routers running at 2.4 GHz.
• 🔋 Headphone Charge: Some Models (JBL Tune 510BT) Disconnected at battery level below 15%.
• 🔄 Reconnect: Remove the headphones from the list of devices and connect again.

No sound in the headphones.

If the headphones are connected, but the sound goes through the TV speakers:

1. On the Xiaomi remote, press the Audio button (speaker icon) and select your headphones.
2. Check the sound settings: Settings → Sound. → Sound output → Bluetooth audio.
3. If used HDMI ARC, Turn it off in Settings → Sound. → HDMI ARC.

4. Alternative ways of connecting: if Bluetooth is not available

If you're Xiaomi. TV Does not support Bluetooth (e.g. Mi). TV 4S "32" or Redmi TV A32), There are three workarounds:

4.1. Bluetooth adapter for USB-port

The most universal solution is to buy an external Bluetooth transmitter with an interface. USB-A. Models will do:

• 🔌 1Mii B06 Pro (supports aptX) LL, minimum delay).
• 🔌 Avantek APT-LD40 (budgetary option AAC).
• 🔌 Creative BT-W5 (for audiophiles, supports 24-bit/96kHz).

How to connect:

1. Insert the adapter in USB-television-port.
2. Put the headphones in pairing mode.
3. On the adapter, press the connection button (usually a blue light flashes).
4. In the settings of the TV, select the sound output → USB.

Connection via 3.5mm audio output

If the TV has a 3.5 mm connector (for example, the Mi). TV 4A 55), you can use a Bluetooth transmitter with audio input:

• 🎵 TaoTronics TT-BA07 (battery, operating time 10 hours).
• 🎵 Mpow BH129 (Supports two devices simultaneously).

Connect the transmitter to the 3.5mm output, then pair with headphones. Minus: the sound will be mono if the TV does not support stereo through 3.5mm.

4.3 Use. TV-prefixes (Android) TV Box)

If you are using an external console (Xiaomi Mi Box S, Nvidia Shield), connect the headphones directly to it:

1. Go to the settings of the consoles (Settings) → Remote & Accessories → Add Accessory).
2. Select the headphones from the list.
3. In the settings of the console sound set Audio Output → Bluetooth.

Standard Bluetooth TV|Bluetooth adapter USB|Transmitter for 3.5 mm|TV-The prefix: Mi Box, Shield)|Other-->

5. Sound optimization: settings for better quality

Even after a successful connection, the sound may not be perfect. Here's how to improve it:

5.1 Selection of Bluetooth codec

Xiaomi TVs on Android TV (Like Mi. TV Q2) allow you to manually select an audio codec:

1. Go to Settings → Devices → Bluetooth.
2. Click on the gear icon next to the connected headphones.
3. Select the Audio Codec and set the priority: aptX LL — Minimum delay (better for movies). AAC — Balanced quality (suitable for music). SBC — universal, but with delay.

Equalizer adjustment

To compensate for the disadvantages of Bluetooth sound:

1. Open the settings → Sound → Equator.
2. Choose a preset movie or speech (for dialogue).
3. Manually increase the sliders 100 Hz (bass) and 3 kHz (voice).

Synchronization of sound and video

If the sound delay remains, calibrate it manually:

1. Turn on a video with a clear sound (for example, clapping in your hands).
2. Go to Settings. → Sound. → Synchronization of sound.
3. Set the latency in the range of 0–200 ms (start with 100 ms).

💡

For Xiaomi models on Android TV 11+ (Mi TV Q2 2023) Dynamic Latency option available in Bluetooth settings – it automatically adjusts the latency in real time.

6. Connecting specific headphone models

Some headphones require a special approach when connecting to Xiaomi TV. Let’s take a look at popular models.

Apple AirPods (all generations)

Because of the proprietary chip. W1/H1 AirPods can connect with errors.Solution:

• Reset AirPods (press the button on the case for 15 seconds until orange blinks).
• On the TV, select Add the device → AirPods (they can be displayed as LE-AirPods).
• If the sound is interrupted, turn off Automatic Switching in AirPods settings on your iPhone.

6.2. Sony WH-1000XM4/XM5

These headphones support LDAC, Xiaomi TV It's not used to improve the sound:

• In the Sony Headphones Connect app, set the codec priority AAC.
• Turn it off. DSEE Extreme – it adds a delay.
• In the settings of the TV, select Bluetooth audio → High quality.

6.3. Xiaomi Mi True Wireless Earbuds

Xiaomi headphones should connect without problems, but sometimes there is an echo.

• Update the headphone firmware through the Mi Home app.
• In the settings of the TV, turn off the Microphone for Bluetooth (Settings) → Devices → Bluetooth → Headphone settings).

7. Frequent mistakes and how to avoid them

User experience shows that most connectivity problems arise from non-obvious errors.-5 among:

• 🚫 Headphones already connected to another device: Disconnect them from your smartphone or laptop before pairing with your TV.
• 🔋 Low headphone charge: Some models (JBL Live 660NC) not visible at battery level < 20%.
• 📱 Xiaomi remote conflict: If the remote uses Bluetooth (like Mi Remote Pro), turn it off before connecting the headphones.
• 🔄 Outdated TV firmware: Update the software through Settings → On TV. → Updating the system.
• 🎮 Occupied audio channel: If the TV is connected to the sound panel through HDMI ARC or optical output, turn it off.

⚠️ Note: If after connecting the headphones sound goes through them and through the TV speakers, check the settings settings → Sound. → Simultaneous sound output and turn it off.

FAQ: Answers to popular questions