Owners of Xiaomi wireless headsets often face a situation where one earbud stops hearing the other or the phone sees them as two independent devices. TWS-Modern models, such as Redmi Buds or Mi True Wireless, require a precise pairing algorithm to work correctly.
The process of reconnecting the ears does not require complex tools or service intervention. In most cases, it is enough to perform a sequence of actions to force the reboot of Bluetooth modules, the main thing is to strictly observe press timings and LED indicators, since the controller firmware is sensitive to input errors.
Before you start manipulating, make sure your devices are at least 50 percent charged. Low charge can cause the Bluetooth antenna to work unstable and interrupt the synchronization process. It is also important to clear the connection history on your smartphone to avoid MAC address conflicts when you re-pair.
Reasons for the desynchronization of headphones
The left-right channel communication can be disrupted for a variety of reasons, and the culprit is often a software failure in the Bluetooth protocol that occurs after a smartphone operating system is updated or a connection break in the area of poor signal reception, in which case the headset memory buffer is overflowing with erroneous connection data.
Physical factors also play a role. Moisture, shocks, or extreme temperature changes can cause a temporary power controller to fail, and if one of the headphones is depleted and has been lying unused for a long time, its communication module may go into deep sleep, which causes it to stop "hearing" the master device command.
Why do headphones look like two different devices?
Another reason is a connection profile conflict: If a headset has previously been paired with multiple devices, it may try to automatically connect to the last active gadget, ignoring the current request. Resetting helps clear this list and forcefully initiate a partner search inside the case.
Preparation for the interface procedure
The success of the operation depends on the correct preparation of the equipment. Before starting work, you need to remove the old device from the Bluetooth list on your phone. To do this, go to the settings, find the name of your Xiaomi Earbuds and select the option “Forget the device” or “Disable”.
It is critical to ensure that the charging contacts are clean. Oxidation or dust on the gold pins inside the case can prevent the timing signal from being transmitted even if the headphones are charging. Wipe the contacts with a dry lilaless napkin and make sure that both headphones sit tightly in the sockets.
- 🔋 Charge the case and headphones to at least 80% for stable operation.
- 📱 Turn off Bluetooth on all nearby devices that were previously connected.
- 🧼 Clean the touch panels and charging contacts with an alcohol napkin.
- 📶 Make sure you are in a safe reception area, away from powerful sources of interference.
💡
If one of the headphones does not light up when you install it in the case, try to press it slightly with your finger. Sometimes spring contacts in cheap models can slightly sag, losing contact with the board.
After the preparatory steps, you can go to the direct reset. Take your time, give the system time to react after each action. Quick steps often result in the controller not having time to go into programming mode.
Universal method of discharge through the case
Most Xiaomi models, including the Redmi AirDots and Mi True Wireless Earbuds Basic, use a similar reset algorithm. Place both headphones in a charging case and leave the lid open. Indicators should light up, signaling the start of charging and ready to go.
Find the pairing button on the case case case, depending on the model, it can be located on the back wall, inside the sockets or on the front panel. If there is no physical button, the touch zones on the headphones themselves play its role. Press the button on the case for 10-15 seconds until the indicator flashes white.
☑️ Reset algorithm through case
When the light flashes, the internal memory is cleared and the Bluetooth modules are rebooted. Then close the case cover and wait 5-10 seconds. Now open the cover again, the lights should flash frequently to signal the search mode.
Reset without a button: touch control
Some budget and compact models don't have a physical button on the case case, and in these cases, the reset procedure is done directly through the headphone touchpads, which requires greater accuracy and synchronization.
Remove both earbuds from the case. At the same time, touch the touch areas on the left and right earbuds and hold your finger for 5-7 seconds until they turn off (the indicators go out). Once turned off, put them back in the case, close the lid for 10 seconds, then pull out.
Now you need to do a double tap. Quickly tap the touchpads of both headphones twice (play/pause mode). If done correctly, the indicators should flash several times, confirming the entry into recalibration mode.
⚠️ Attention: When performing a reset through touch panels, it is critical to press both earphones at the same time.
After successful manipulations, the headphones must automatically find each other, usually one indicator (master device) flashes slowly, and the second (slave) flashes quickly or goes out, waiting to connect to the first one, only after they connect to each other, they can be connected to a smartphone.
Specificity of connecting different models
Xiaomi’s audio lineup is extensive, and each series has its own characteristics. Understanding the differences helps avoid mistakes when trying to combine Redmi Buds 3, Mi True Wireless Earphones 2 or older versions of AirDots.
| Model | Type of discharge | Indication of success | Features |
|---|---|---|---|
| Redmi AirDots / Mi TW Basic | 5 seconds in a case or 20 seconds out | Double blinking. | Often double reset is required. |
| Mi True Wireless 2 / 2S | Case button 15 seconds. | White flashing | Support for wireless charging |
| Redmi Buds 3 Pro | Double touch of the sensor | Sound signal | I need the Mi Buds app. |
| Xiaomi FlipBuds | Through an application or case | LED pulse | ANC noise suppression |
For advanced models such as Redmi Buds 3 Pro or FlipBuds, it is recommended to use the official Mi Buds or Xiaomi Earbuds app. It allows you not only to connect headphones, but also to update their firmware, which often solves compatibility problems at the software level.
If standard methods don't work, try hard reset. Leave the headphones out of the case until the battery is completely drained. Then set them to charge for 30 minutes without opening the lid. Then reset the reset procedure. This method helps to reset static electricity and reset the power controller.
Solution: One earphone is not working
It's common for the master device to connect to the phone, but not to send the audio stream to the slack. Check the balance of the sound in your smartphone's Bluetooth settings. Sometimes the balance slider is shifted completely left or right.
Try connecting your headphones to another device. If the problem persists, it's hardware or headset firmware. If the other phone is working, clear the Bluetooth cache on your main smartphone through the Settings menu → Apps → Show system → Bluetooth → Memory → Clean.
⚠️ Warning: Do not try to connect the headphones if they are in different modes of operation (for example, one in game mode, the other in music mode.
In rare cases, flashing is required. For models with application support, this is done automatically. For simple AirDots, flashing is only possible in the service center through a special programmer, since they do not have a user interface to update.
💡
If after resetting and reconnecting, the sound still comes from only one headphone, the problem may be hardware damage to the speaker or plume, not a software failure.
Prevention and care TWS-headset
To keep the desynchronization problem from returning, it's important to store the device properly. Always put the headphones in the case after use. Left on a desk or in a pocket outside the case, they can discharge to zero or accidentally connect to third-party devices, which confuses the priority settings.
Regularly update your firmware through the app. Xiaomi developers often release patches that improve the stability of Bluetooth connections and fix bugs with channel desynchronization. Ignoring updates can lead to an accumulation of errors in the system.
- 🧼 Clean the speaker mesh with a soft brush once a week.
- 🔋 Do not allow deep discharge (storage with 0% charge kills the battery).
- 📱 Turn off Bluetooth on your phone when you are not using the headset.
- 💧 Keep electronics from condensation (do not carry them in the freezer).
Compliance with these simple rules will prolong the life of your Xiaomi headphones and provide stable stereo sounding. Remember that electronics do not like extreme conditions and careless handling.