When your favorite wireless headphones suddenly stop responding to commands, it always takes you by surprise. Users often experience a case burning, but the Redmi Buds or Mi True Wireless themselves remain dead, which can be a trivial discharge, a software failure, or a more serious hardware problem.
In most cases, it is early to panic, because the device has simply gone into deep sleep or lost contact with the charger. However, you can not ignore the problem, because if the headphones are not turned on, it can lead to complete failure of the battery. In this article, we will discuss in detail all possible scenarios of failure and methods for their elimination.
Before you bring it into service, you need to do a series of simple manipulations that bring it back to life 80 percent of the time, and often the critical factor is the oxidation of the contacts on the headphone itself, which blocks the current flow. Let's go through the diagnostic and recovery steps in a sequential manner.
Diagnosis of nutrition and charging case
The first thing you need to check is the state of the charging case, which is the source of energy for the battery. TWS-If the case is zero, it can't activate the internal electronics of the ears. 30-40 minutes, even if the indicator does not immediately light up.
Often the problem lies in the cable itself or the power supply. Use the original USB-C cable or a quality analogue with support for at least 1A. Weak computer ports or power banks with low recoil current may not start the charging process if the battery of the case has gone into deep discharge.
And you can look at the LED light, and its behavior can tell you a lot about the state of the system.
- 🔴 Burning red - the charging process is underway, the battery of the case is discharged.
- 🟢 Burning green or white – the case is fully charged or the charge is complete.
- ⚪ Flashing white - pairing mode or device search.
- ⚫ Does not burn - possible failure of the battery case or lack of contact.
⚠️ Note: If the case indicator lights up and immediately goes out when installing headphones, this may signal a short circuit inside one of the modules or a strong oxidation of contacts.
Make sure you use a proper outlet. Sometimes users sin on the equipment when the problem is trivial in the extension or network filter. Check the charger on other gadgets to rule out a malfunction of the power supply.
Contact group problems and oxidation
One of the most common reasons why shaomi headphones are not turned on is a disruption of electrical contact, which accumulates earwax, dust and oxides on the golden charge pens, creating an insulating layer that prevents charging.
To clean, use a cotton swab lightly soaked in isopropyl alcohol or a special electronics cleaner. Gently wipe the contacts on the headphones themselves and inside the case. Do not use water or aggressive solvents that can damage plastic or internal electronics.
After cleaning, let the alcohol evaporate completely within 2-3 minutes. Then place the headphones in the case and press them slightly with your fingers to make sure that the contact is tight. If contact is restored, the case LED should react with a change in color or light up.
In some models, such as the Redmi AirDots, the contacts can become inflamed or deformed when falling.Visually inspect the pencils: if they are pressed or skewed, neat mechanical repair or module replacement will be required.
💡
To prevent oxidation, wipe contact groups with dry soft cloth every two weeks, especially if you use headphones while exercising.
Resetting settings and software resuscitation
If the power is all right, there may have been a software firmware failure, where the microcontroller inside the headphones could freeze, which causes them to stop responding to external commands, in which case a forced reset will help.
The reset procedure varies from model to model, but the overall algorithm is often similar, usually requiring the earbuds to be removed from the case and pinching the touch areas or physical buttons on the case. 10-20 In some cases, the procedure must be performed when the headphones are inside the case.
Consider the checklist of actions to reset most models:
☑️ Algorithm reset headphones Xiaomi
Once you reset, remove the device from the Bluetooth list on your smartphone. Find in Bluetooth settings → My devices, select your headphones and click "Forget device" or "Cancel pairing." Then search again.
⚠️ Warning: Do not reset if the headphones are on a table without a case and they have a battery that has run out. This can finally discharge the power controller, and the device will stop turning on completely.
Sometimes it helps to "swing" the battery. Leave the headphones in a closed case for charging for several hours (up to 4-5 hours). Even if the indicator does not burn, low currents can gradually raise the voltage on the battery to a level sufficient to start the system.
Compatibility table and type failures
Different Xiaomi headphone lines have their own design features, understanding the model helps to find a solution faster. Below is a table with common problems for popular series.
| Model | Type of management | Frequent reason for refusal | Method of decision |
|---|---|---|---|
| Redmi AirDots / Mi True Wireless | Mechanical button | Button sticking or oxidation | Repeated pressing, alcohol cleaning |
| Mi True Wireless Earbuds Basic 2 | Sensor + button | A rupture of the plume inside the case | Checking the contacts of the Pyats |
| Xiaomi FlipBuds Pro | Touch + Noise Maker | ANC firmware error | Full reset via app |
| Redmi Buds 3 / 4 | Touch-sensitive | Deep battery discharge | Long-term charging (3+ hours) |
Active noise cancellation (ANC) models are characterized by more complex break-down scenarios, and if the microphones get clogged with dust, the system can block the speakers from working, creating the illusion of a non-working device.
Owners of advanced models are advised to use the Xiaomi Earbuds or Mi Home app, which allows you to check the firmware version and, if the device reacts, update the software, sometimes bugs in the old firmware interfere with the correct start of the system.
Secret Diagnostic Regime
Effects of temperature and operating conditions
Lithium polymer batteries used in TWS-If you leave your phone in your car in the winter or in the cold, the chemical reactions inside the battery slow down and it stops giving off current.
In this case, the device may not turn on, even if the battery is charged, you need to place the case with headphones in room conditions for 30-60 minutes, do not try to heat them with a hairdryer or put them on the battery - this can cause the battery to bloat.
High humidity is also the enemy of electronics. Sweat or rain can short circuit the board. If the headphones get wet, remove them immediately from the case (if it's dry) and put them in a silica gel container.
Condensate generated inside the body at a sharp temperature difference can close the contacts, in this case, the device is strictly prohibited until completely dry, otherwise you can burn the charge controller.
💡
Temperature shock is a temporary phenomenon, so let the device warm up to room temperature naturally without using heaters.
When professional repairs are needed
If all of these methods didn't work, there's probably a hardware breakdown, which could be a battery failure that lost capacity and no longer holds charge, or a control board damage.
Symptoms requiring the intervention of an engineer:
- 🔋 Headphones charge for 5 minutes and immediately turn off.
- 🔥 Case or headphones are very heated when charging.
- 💧 Clear traces of fluid entering the body.
- 🔊 The appearance of cod, wheezing or complete absence of sound when working.
Self-disassembly TWS-The plastic often cracks when you try to open it, and the small components are easily damaged by inexperienced hands.
Keep in mind that the cost of replacing a battery or board in miniature devices is often comparable to the price of a new budget device. therefore, repairing expensive models (FlipBuds Pro, Buds 4 Pro) makes sense, and resuscitating old AirDots 1 may not be economically feasible.