How to increase volume on Xiaomi Redmi 4X

Xiaomi Redmi 4X has earned the status of a popular favorite due to its reliability and autonomy, but many users eventually begin to notice that the level of sound played has become not high enough, this is especially critical in noisy places or when watching videos without headphones, when standard MIUI regulators are no longer enough for comfortable listening. Often the problem lies not in the breakdown of the speakers, but in the software limitations or failures of the audio codec settings.

There are many ways to fix this and make the most of your device’s acoustic system without having to resort to complex hardware repairs. In this article, we’ll look at proven methods for amplifying sound, ranging from simple interface settings to more advanced manipulation of system settings through the engineering menu. Data security and system integrity will remain a priority, so all instructions are tailored to minimize risks.

Before we move on to radical measures, we need to rule out the trivial causes of quiet sound, such as pollution of the speaker grid or activation of energy saving modes, which can limit the performance of the audio chip. A competent approach to tuning will allow you to return to the former volume and even surpass factory performance, providing a richer and more powerful sound.

Basic sound setting in the MIUI interface

The first step should always be to carefully check the standard operating system settings, as users often overlook the hidden features of the equalizer. The MIUI shell installed on the Redmi 4X has a built-in audio module that allows you to adjust the frequency characteristics and the overall output level. Go to the settings menu and find the section responsible for sound and vibration to make sure that all sliders are brought to maximum.

Special attention should be paid to the Dolby Atmos or Mi Sound settings, if available in your firmware version. These technologies can significantly improve audio perception by adding volume and depth, which subjectively increases volume, and the headphone settings should not be ignored, which sometimes affect the overall output profile even when using external speakers.

For detailed adjustment, use the built-in equalizer, where you can manually lift all the frequency sliders, creating a user profile with maximum amplitude. However, be careful: excessive amplification of low frequencies can lead to wheezing and distortion, since the speaker membrane has physical limitations as the movement goes.

• 🎚️ Open the sound settings and select "Sound Quality" or "Equalizer".
• 🔊 Set all frequency sliders in the upper position for maximum signal amplification.
• 🎧 Activate the "No Headphones" mode in the Mi Sound settings, if such a item is present in your version MIUI.
• 📵 Turn off Do Not Disturb mode and make sure system sounds are also max-wiped out.

⚠️ Attention: A sharp increase in all equalizer frequencies can cause distortion and wheezing if the speaker is not designed to handle such a load.

💡

Before changing the settings of the equalizer, write down the initial values or take a screenshot so that in case of deterioration in the sound quality, you can quickly return to factory parameters.

Using an Engineering Menu to Enhance Audio

The most effective software method for increasing volume on Xiaomi smartphones, including the Redmi 4X model, is the use of a hidden engineering menu, which is designed for engineers and allows you to directly control the levels (amplification) of audio paths at the driver level of the device.

To enter the test mode, you need to dial the combination ##6484## or #3646633##, and then the CIT (Customer Integration Test) interface will open. You are interested in the section related to audio tests, usually called Audio or located in the Hardware Testing menu. Here you can find the volume settings for various scenarios: speaker, multimedia, alarm clock and bell.

Inside the Level Selection menu, you need to select the maximum value available for your region (usually General or Headset) and then go to the Type of Sound setting. By choosing Media type (media), you can push the Max Vol slider to the limit. The standard value is often 140-150, but it can be increased to 160 or higher, but exceeding critical values can cause the membrane to rupture.

After making changes, be sure to press the Set or Apply button to save new settings to nonvolatile memory.Rebooting the device is not always necessary, but desirable to properly initialize the audio codec with new parameters. If the sound becomes too loud or distortions appear, go back to the same menu and lower the values.

Third-party applications for sound amplification

If the built-in tools are not enough, specialized applications from the Google Play store come to the rescue, which work as software amplifiers, such as the Volume Booster GOODEV or Precise Volume, create an additional signal amplification cascade by letting the audio stream through its algorithm before sending it to the speaker, which allows you to exceed the system limit of 100% volume.

However, using third-party software has its nuances: applications can consume additional battery power and create a load on the processor. In addition, poor-quality amplification algorithms can make digital noise and crack, especially at maximum boost levels. It is important to choose proven solutions with high ratings and a lot of positive feedback from Xiaomi users.

When you first start an application like this, it's recommended that you don't set the gain immediately to maximum. 20-30% And gradually increase the value until you reach a comfortable level or the first signs of distortion. Remember that digital amplification does not create new energy, but only increases the amplitude of an existing signal, which can reduce the overall sound quality.

• 📲 Download a proven volume booster, such as Volume Booster Plus.
• ⚙️ Give the application the necessary permissions to change the system settings of the sound.
• 🎚️ Set the Boost gain level to the mark 20-40% start-test.
• 🔊 Check the sound on different types of content: music, video, voice messages.

⚠️ Warning: Long-term use of maximum amplification through third-party applications can cause the audio chip to overheat and accelerate wear of the Redmi speaker 4X.

Physical cleaning and speaker maintenance

Often the quiet sound on the Redmi 4X is caused by the banal contamination of the speaker grid with dust, pile and skin fat, which accumulate during operation. Microscopic particles clog the perforation, preventing the free passage of the sound wave, which subjectively reduces the volume by 30-50%. Regular cleaning can return the device to its original acoustic characteristics without any software intervention.

To clean, you'll best use a soft toothbrush with dry bristles or a special cleaning gel Velcro for electronics. Carefully brush the speaker's grid, sweeping the dust out, but don't press too hard to damage the membrane. You can also use compressed air in cans, feeding short jets at an angle to knock out the contaminants from the depths of the case.

There is a popular but controversial method of blowing dirt by turning on a low-frequency (20-50 Hz) audio file at maximum volume. Vibrating the membrane at low frequencies can indeed push some of the dust out, but this method is only effective for mild contaminants. If the speaker is clogged tightly, mechanical cleaning will remain the only effective solution.

If the sound is still quiet or crackling after cleaning, the problem may be oxidation of the contacts of the speaker plume or physical damage, and in such a situation, the software methods are powerless, and you will need to disassemble the device to visually inspect the component, sometimes helping to reconnect the plume, which restores normal contact and signal level.

• 🧹 Use a dry soft brush to remove surface dust from the speaker mesh.
• 💨 Use a compressed air can to blow through the internal channels (short-term).
• 🔊 Use the low-frequency test track for vibrational membrane cleaning.
• 🔍 Inspect the net for severe contaminants that require careful needle removal.

Problems with Bluetooth and external devices

Sometimes users are faced with a situation where the volume of the phone appears low only when connected to a Bluetooth headset or speaker, while the smartphone itself sounds normal. This is due to the desynchronization of volume levels between the source (Redmi 4X) and the receiving device. In the Android system, there is a feature "Absolute Volume" that connects the device regulators and the headset together, but it may not work correctly.

To solve this problem, you can try turning off the absolute volume function through the developer menu, and you need to click on the build number in the About phone section several times, activate the developer mode and find the "Disable absolute volume level." After switching this option and rebooting the Bluetooth connection, the sound levels should unlock and become independent.

It’s also worth checking the settings of the Bluetooth device itself: some speakers and headphones have their own volume controls that can be twisted to a minimum. Make sure the external device also has a maximum level before blaming the smartphone for quiet sound.

⚠️ Warning: Turning off absolute volume can cause the regulator on the phone to stop affecting the volume of the Bluetooth device, and you will have to adjust it with buttons on the headset itself.

💡

Bluetooth volume desynchronization is often solved by switching the "Absolute Volume" option in developer mode or reconnecting the device.

Hardware Limitations and Dynamic Replacement

If neither software tweaks nor cleaning helped, and the sound became quiet and hoarse even at a minimum volume, it is likely a hardware malfunction. The speaker in Redmi 4X is a consumable that loses its properties over time: the magnet demagnetizes, the coil deforms, and the membrane suspension tantalizes, in which case the increase in volume of the software will only aggravate the distortion.

Replacing the speaker is a low-cost procedure that is affordable for beginners, and a new original or high-quality analog speaker can restore the factory volume and add basses that the old one lacked. When choosing a part, pay attention to the power (usually 1 W or 1.5 W) and dimensions to ensure that the component fits exactly into the seat.

It is also important to check the connector status on the motherboard: if the contacts are oxidized or bent, the signal will come in weaker. In rare cases, the problem may lie in a malfunction of the audio codec on the board, which requires more complex component repair in the service center. However, in 90% of cases on older smartphones, it is the speaker himself who is to blame.

Frequently Asked Questions (FAQ)