The Xiaomi Mi A2, part of the Android One program, has proven to be a reliable device with a clean interface and quality components. However, many users face a situation where the standard power of the built-in speaker is not enough to comfortably listen to music or watch videos in noisy conditions. The problem may be not only hardware limitations, but also software settings that by default limit the output signal to protect the user’s hearing.
In this article, we will discuss in detail how to increase the volume of the speaker on the Xiaomi Mi A2, using both standard operating system tools and third-party solutions. We will look at the hidden debugging menus that allow you to customize the audio profile of the device more flexibly than the standard menu. It is important to understand that interference with the system parameters of sound requires caution, so as not to damage the acoustic system.
Before we go to radical methods, it’s worth checking out basic settings that are often ignored. Android provides built-in tools to correct frequency balance, which can visually increase the perceived volume. In addition, there are a number of physical factors, such as contamination of the speaker grid, which trivially reduce the sound output, and their elimination can return the device to factory power.
Basic sound tuning and system cleaning
The first step in the struggle for quality sound should be a thorough check of the standard settings and physical condition of the device. Often users forget that the Xiaomi Mi A2 does not have a separate 3.5 mm connector, and the sound is transmitted via USB-C or Bluetooth, which also affects the final perception.
The standard Normal profile often has a flat amplitude, whereas the choice of a Bass Boost profile or manually adjusting sliders can significantly raise the overall sound pressure level, especially for low bitrate tracks where the lack of frequencies makes the sound quiet and flat.
Cleaning the dynamic grid is a procedure that cannot be ignored. Over time, pile, dust and skin fat accumulate in the holes, forming a dense plug. You can use a soft toothbrush or a special sticky tape to clean, but you can categorically not use sharp objects or compressed air under high pressure, as this can damage the speaker membrane.
- 🔊 Check if the “Silence” or “Do Not Disturb” mode is activated in the notification curtain.
- 🧹 Carefully clean the bottom grille speaker with a soft dry brush from the pile.
- ⚙️ In the sound settings, select the equalizer profile "Bright" or "Rock" to increase volume.
- 🔌 Make sure the adapter USB-C 3.5 mm (if used) has a built-in DAC.
Using an engineering menu to customize audio
The most effective way to increase the volume of the speaker on Xiaomi Mi A2 At the system level, it's the use of an engineering menu, which is a hidden part of the operating system that's designed to be used by engineers in the factory to test equipment. USSD-codes that open the debugging interface.
To enter the menu, you need to dial the code ##3646633## in the Phone application. If the standard code does not work, as happens on some versions of Android One firmware, you can use third-party utilities from Google Play, for example, MTK Engineering Mode, since the Snapdragon 660 processor in the Mi A2 has a specific architecture. In the open menu, you should go to the Hardware Testing tab, then select Audio and Audio Debugging.
Inside the Audio Debugging section, you'll find a complex table with parameters, we're interested in Speech (for conversational speaker) or Media (for multimedia sound), and you can change the level (usually from 0 to 6), you can change the Max Vol or Gain. You can increase the values Step-by-step, you can get the power output, but here's the main risk: setting maximum values can lead to wheezing or rupture of the membrane.
⚠️ Warning: Changing the parameters in the engineering menu can lead to irreversible damage to the dynamic system.Do not set Gain values above the manufacturer's recommended values (usually no more than the following: 120-130 dB).
What if the code doesn't work?
Application of third-party sound amplifiers
If you're messing with system code, Google Play's amplifiers come to the rescue, and the way they work is by software amplifying the audio stream before it's sent to a digital-to-analog converter, which bypasses the software constraints set by the manufacturer for the Xiaomi Mi A2.
One of the most popular and reliable solutions is the Volume Booster GOODEV application, which is easy to use: once installed, you just need to move the gain slider. However, it is worth remembering that software amplification always causes distortion. The higher the percentage of the boost, the more noticeable the wheezing and loss of detail of sound, especially at low frequencies.
Another powerful tool is Equalizer FX, or the built-in equalizer in some players, such as Poweramp. These applications allow not only to raise the total volume (Preamp), but also to adjust the frequency balance, making the sound clearer and more penetrating.
- 📲 Install the Volume Booster app GOODEV fast-forward.
- 🎛️ Use the Preamp option in the equalizer to increase the signal level.
- 🎧 Connect external active speakers for maximum power.
- 🔊 Do not exceed the level of gain in 20-30%, squirm.
💡
Software amplifiers are a trade-off between volume and quality. With a strong boost, the sound becomes flat and different (distorted).
Comparison of volume-raising techniques
The choice of method depends on your technical skills and willingness to risk the integrity of the device. Each method has its advantages and disadvantages, which should be considered by owners of Xiaomi Mi A2. Below is a comparison table to help determine the best solution.
| Method | Difficulty | Risk of damage | Efficiency |
|---|---|---|---|
| Cleaning the dynamics | Low. | Minimum | Medium (return to normal) |
| Equalizer (staff) | Low. | Absent. | Low/Mediocre |
| Engineering menu | Tall. | High-pitched | Maximum |
| Booster applications | Medium | Medium (distortion) | Tall. |
It’s worth noting that the engineering menu gives you access to hardware limits, whereas applications only work with software flow. If the speaker is physically healthy but quiet, then changing the Gain parameters in the engineering menu is the only way to really increase the power limit that a smartphone amplifier can give.
Amplifiers are more convenient for temporary use, for example, when you need to urgently make the sound louder in a noisy place, but for constant use, it is better to adjust the equalizer or carefully adjust the system limits so as not to load the processor with additional calculations in real time.
Problems with codec and Bluetooth headsets
Often the question of how to increase the volume of the speaker on the Xiaomi Mi A2, arises when connecting wireless headphones or speakers, in this case, the problem lies not in the smartphone itself, but in the protocols of data transfer or desynchronization of volume levels between devices.
Android has a "Absolute Volume" feature that links the phone's volume slider to the headset, and sometimes it doesn't work properly, limiting the maximum level. You can turn it off from the Developer menu. To get there, you have to click 7 times on the build number in the About section, and then find the "Open Absolute Volume" item and activate it.
Also worth paying attention to the codec used. Xiaomi Mi A2 supports AAC, SBC and aptX codecs. High-bitrate codecs (aptX HD) can transmit more dynamic sound, but when the signal is poor, the system can lower the volume to stabilize the connection. Switching to SBC in Bluetooth settings sometimes solves the problem of quiet sound.
☑️ Bluetooth Sound Checking
Physical limitations and modernization
And you have to realize that the Xiaomi Mi A2 is a device with a monophone speaker at the bottom of the body, and its physical size is limited by the size of the smartphone body, and no program can make a small speaker produce a bass as powerful as a large speaker without the risk of mechanical failure.
If the sound is severely lacking, the smartest solution is to use external accessories: Portable Bluetooth speakers or wired amplifiers (DAC/AMP) connected via USB-C, can unlock the potential of the Mi A2 digital audio stream at a whole new level.
In rare cases, a quiet sound may indicate a malfunction of the speaker module itself. If after all the software settings the sound remains quiet, hoarse or intermittent, it is likely that the acoustic module in the service center will need to be replaced, which is especially true for devices that have been in a wet environment.
⚠️ Attention: Attempts to independently disassemble Xiaomi Mi A2 If you replace a speaker without experience, you can damage the plumes and lose water protection.
💡
If you want to make the sound louder without the technique, put the smartphone down on an empty glass jar or in the corner of the room with the speaker, and it will amplify the sound in a natural acoustic way.