How to sync Xiaomi Earbuds Basic Headphones 2: The Complete Guide

Modern. TWS-Headphones have become an integral part of everyday life, providing freedom of movement and sound quality. Xiaomi Earbuds Basic 2 has proven to be a reliable and affordable solution, but sometimes users face difficulties in the initial start or restore communication. Proper synchronization of the device is the foundation of stable operation of Bluetooth connection and high-quality sound.

Often, one of the headphones stops working or they don't see each other, which leads to sound playback in only one ear. This does not mean that the gadget breaks, most often you just need to re-mating. In this article, we will discuss all the nuances of how to properly combine channels and connect the accessory to your smartphone.

You don't have to be a technician to do this. All manipulations take a few minutes and only require attention. Let's take a step-by-step algorithm to help you enjoy your favorite music without interruption.

⚠️ Warning: Before any synchronization actions are initiated, make sure that the case and the headphones themselves are charged. A discharged battery can cause indicators to flash incorrectly and pairing mode to malfunction.

Initial preparation and charging check

Before trying to pair the Xiaomi Earbuds Basic 2 with your phone, you need to rule out power issues.Often the device simply doesn't turn on or goes into standby mode if the charge level is critically low.Put both headphones in a charging case and plug it into the power source for 15-20 minutes.

Pay attention to the indicators. When you take your headphones out of your case, they should light up. The red indicator usually signals low charge or charging, and the white indicator indicates readiness to work. If the indicators do not light up, wipe the contacts on the headphones and inside the case with a dry cotton swab, as oxidation can interfere with current transmission.

Make sure your smartphone has Bluetooth enabled. It is also recommended to enable geolocation for proper operation, as some versions of Android require location access to search for Bluetooth devices.

The process of first connecting to a smartphone

When you take your headphones out of your case for the first time, they automatically go into Pairing, at which point the lights start flashing white quickly, which means that the device is visible to other gadgets, you need to open the Bluetooth settings on your mobile device.

In the list of available devices, find the name Xiaomi Earbuds Basic 2 or Redmi Earbuds Basic 2. Click on it to pair. If the system requests a confirmation or code, agree to connect. After successful synchronization, the headphones should flash less often or go out, indicating a stable connection.

Automatic connectivity only works if the Bluetooth on the phone is active.If you want to switch to another gadget, first turn off Bluetooth on the old device or choose the headphones manually in the new one.

What to do if only one headphone is working

One of the most common problems with TWS-Headsets -- desynchronization of channels, where the sound is only on the left or right, and this happens when the headphones have forgotten each other and one of them has connected to the phone as an independent device, and to fix this, you have to reset the settings and force them to reunite.

First, remove the Xiaomi Earbuds Basic 2 from your phone’s Bluetooth settings list. Then turn off the Bluetooth on your smartphone completely. Place both headphones in your case, close the lid and wait 10 seconds. Then pull them out at the same time.

Now reset. To do this, touch the touch zone on both headphones simultaneously and hold your finger for about 5-7 seconds until the indicators flash red three times (or go out, depending on the firmware version). Then put them back in the case, close and pull them out again. They must automatically find each other, and only after that (in a couple of seconds) you can turn on Bluetooth on the phone and search for the device.

⚠️ Warning: Don't try to connect your headphones to your phone until they're in sync with each other. If you see two devices with the same name on the list, they're not paired with each other.

Table of indicators and their values

Understanding the light signals helps to quickly diagnose the state of the headset, and different blinking modes tell the user about the current status of the device without having to look into the screen of the smartphone.

If you see non-standard display behavior, such as chaotic blinking with both colors, it may indicate a deep discharge or software failure, in which case leave the headphones in the case on charge for 1-2 hours, even if the indicators do not light up immediately.

Removing visibility problems of the device

Sometimes, a smartphone simply doesn’t see the Xiaomi Earbuds Basic 2 on the list of available devices, even if the headphones are in pairing mode.This could be due to the phone’s Bluetooth module cache or third-party apps blocking search.

Try rebooting your smartphone. It's a banal but often-working tip that cleans temporary files and restarts communication services. Once you turn on your phone, immediately go to device search. Also check if your headphones are connected to another device nearby, such as a tablet or laptop. Connection priority is often given to the last active gadget.

In rare cases, cleaning the list of conjugate devices helps: remove all old, unnecessary Bluetooth profiles from the phone's memory. An overflowing list can slow the scanning process. If the problem persists, try connecting the headphones to another smartphone to localize the problem: in the headphones or in the phone.

💡

If you can't see the headphones, try to get closer to the Wi-Fi router or, conversely, move away from it. Sometimes the 2.4 GHz Wi-Fi and Bluetooth frequencies conflict, causing interference.

Features of working with different OS

The sync process on Android and iOS is almost identical, but there are nuances in displaying battery power. On Android, to accurately display the percentage of charge of each headphone and case, you may need the Xiaomi Earbuds or Mi Wear app. Without it, you will only see the overall charge level.

iOS users may find that the names of the control buttons do not match reality, since iOS does not support the full proprietary Xiaomi protocol. However, the basic functions - playback, pause, call taking - work correctly. iPhone owners will have to use an Android device to adjust gesture management or accept standard settings.

On MIUI shell devices, pairing is faster thanks to the ecosystem. A case animation pop-up appears automatically when the lid is opened next to the unlocked phone. If the window doesn't appear, check if the Bluetooth service plugin is updated in the system settings.

⚠️ Note: When connecting to Windows PC, you may need to enter PIN-It's usually 0000 or 1234, but most of the time, the system asks for confirmation without a code.

Frequently Asked Questions (FAQ)

💡

The main secret of stable operation is always to remove both headphones from the case at the same time and give them 3-5 seconds for mutual synchronization before turning on Bluetooth on the phone.