Wireless speakers often face a situation where the Bluetooth headset stops working correctly, loses connection or makes extraneous noises. Owners of popular models from Xiaomi sub-brand Haylou are no exception. The accumulation of software errors in the device buffer or conflicts when pairing with a new smartphone may require a complete return to the original state.
Factory resetting is a universal solution to most software failures, a process that removes all stored pairs of devices from the headphone memory and restarts their internal operating system. Below we will discuss in detail the reset methods for different models so that you can quickly return your resets. TWS-Headphones to life without contacting the service center.
It's worth noting that the procedure may vary slightly depending on the series of devices, with some models being controlled exclusively through touch zones, while others require physical buttons, and it's important to pinpoint your modification to choose the right algorithm.
Preparing for resetting and cleaning the pairing list
Before you start manipulating the headphones themselves, you need to do the preparatory steps on the smartphone. Cleaning the pairing list in the Bluetooth settings of the phone is a critical step that is often ignored. If you don't remove the old device from the phone's memory, after reset, the headphones may become invalid again or not be visible at all.
Go to your Android or iOS device's Bluetooth settings. Find your Haylou GT1, GT3 or other device available on the list. Click on the gear icon or arrow next to the name and select "Forget the device" or "Cancel pairing." After that, it is recommended to turn off the Bluetooth on your phone completely during the reset procedure.
⚠️ Warning: Before starting the reset, make sure that the case and the headphones themselves are charged at least 50.
It’s also worth checking if the headphones are connected to other gadgets nearby. Signal interference or attempting to automatically connect to a tablet or laptop can prevent the reset command from being executed. Make sure that only your main smartphone is active within a 10-meter radius, and then with Bluetooth turned off.
☑️ Preparation for discharge
Reset settings on Haylou GT1, GT1 Pro and GT1 Plus models
The GT1 series is one of the most popular and has its own control features, characterized by the use of touch zones on the outside of the case, and the reset procedure is performed without removing the headphones from the charging case, which is important for maintaining charge and stability of the process.
Place both earbuds in the case and make sure they start charging (the indicators should catch fire). If the case is closed with the lid, leave it open. You need to press and hold the touch zones on both earbuds at the same time. The retention time is about 20 seconds. Visual confirmation of a successful reset will be the flashing of the indicators in red and white three times in a row.
💡
If you can not press both headphones at the same time from the first time, try to gently press them with your fingers through the open case cover, without removing the devices themselves.
Sometimes users are faced with the headphones not responding to touch.In this case, try first removing them from the case so they turn off, then inserting them again and starting the countdown right away.Touch panels can be sensitive to finger moisture, so make sure your hands are dry.
Once the blinking series is successful, the headphones will automatically go into pairing mode, the indicators will flash white frequently to signal readiness for a new pairing, and you can now turn on Bluetooth on your phone and find the device in the list.
Instructions for Haylou GT3, GT3 Pro and GT4
The GT3 and GT4 have improved ergonomics and slightly modified sensor logic, and touch zone retention is also used, but the time intervals can be more stringent. Put the headphones in the charging case, leaving the lid open to see the indication.
At the same time, tap the touch areas on both headphones and hold your finger for 5 seconds until the indicators turn red. Once the red light comes on, release the sensors. Then repeat the action: press and hold again for about 20 seconds. The indicators should flash red three times, confirming a successful reset to factory settings.
| Model | First action. | Second act. | Indication of success |
|---|---|---|---|
| GT1 / GT1 Plus | Hold 20 seconds. | — | 3 blinkings (red/white) |
| GT3 / GT3 Pro | Hold 5sec (red) | Hold 20 seconds. | 3 flashing red |
| GT4 | Hold 5sec (red) | Hold 20 seconds. | 3 flashing red |
| Morr / W1 | Hold it 7 seconds. | — | Fast blinking. |
It's important not to confuse reset mode with game mode or voice assistant activation mode. Short taps usually change tracks or call an assistant, whereas reset requires long-term exposure. If you accidentally activate voice search, just interrupt the action and start again.
Features of resetting headphones Haylou GT5 and GT6
The latest GT5 and GT6 models often feature more sophisticated electronics and support for high-resolution codecs, and the process of rebooting them may require more accurate timing.
Press and hold the sensors on both headphones for 5 seconds before the red glow appears. Release and immediately press again, holding for about 15-20 seconds. The successful completion of the procedure is considered a triple flash of indicators. After that, the Bluetooth module will completely clear the pairing cache.
⚠️ Note: If after reset, one earphone does not connect to another (only one channel works), repeat the procedure again, but before that completely discharge the case and headphones, and then charge them to 100%.
Sometimes it is useful to check firmware updates through the Haylou Fun app after a reset, which will eliminate known bugs that may have caused unstable work.
Solving Case and Indication Problems
There are situations when the headphones themselves are working, but the charge case causes problems. If the headphones do not light up when placed in the case, the contact areas may have become contaminated. Carefully wipe the golden contacts on the headphones and inside the case with a dry cotton swab or soft cloth slightly moistened with alcohol.
The lack of response to the reset may indicate that the headphones do not see the case and do not realize that they are placed in it. Make sure that the magnets tightly attract the headphones, and they sit flat. If one earphone hangs higher than the other, the circuit does not close, and the reset command will not be performed.
What to do if the indicators are not burning?
In rare cases, the case itself may need to be reset if it has its own battery and display, and some models require holding the button on the back of the case (if designed) for 10 seconds.
Actions after successful resetting of settings
Once the indicators have confirmed the reset, your Haylou is in search mode. Turn on Bluetooth on your smartphone and start looking for new devices. The list should show the name of your model, for example, Haylou GT1 or Haylou-GT3.
When you first connect, the phone can request permission to access contacts and call logs. This is standard procedure for headsets that support a profile. HFP (Hands-Free Profiles Allow access if you plan to use headphones for conversations.
- 🎧 Check the volume balance: Make sure the sound is equally loud in both channels.
- 🔋 Test the case: put the headphones back and make sure they start charging.
- 📱 Remove old profiles: If a gray device with the same name is left in the Bluetooth list, delete it.
If the sound is interrupted after the connection or there is a dissynchronization between the channels (in one ear there is sound, in the other ear there is no sound or it lags), this may indicate a hardware problem or a severe radio interference.
💡
Once reset, the headphones are perceived by the phone as a new device, so the old connection needs to be manually removed before each new connection attempt until the problem is resolved.