Using Xiaomi wireless headphones gives you freedom of movement and high-quality sound, but sometimes users face an unpleasant situation: only one headphone is running, or devices can not sync with each other. This is a common problem that often occurs after a smartphone change, battery drain or software failure. Proper synchronization of the left and right channel is the key to stereo sound and full use of all the functions of the gadget.
In this article, we will discuss how to connect both Xiaomi Earbuds headphones to a phone, tablet or laptop. You will learn about standard pairing methods, how to force synchronization between each other and methods of completely resetting the settings. Recovery of the headset usually takes no more than a couple of minutes, if you know the right sequence of actions.
Before you start complex manipulations, you should make sure that the problem is not the banal discharge of the battery or contamination of contacts. Often it happens that one of the headphones just “falls asleep” and does not go out of standby mode. Careful checking of the charging case and the headphones themselves is the first step to solving the problem.
Initial preparation and charging check
Any setup process starts with a steady power supply. If one of the headphones is discharged to zero, it will not be able to pair and sync with the main module. Place both headphones in the charging case and make sure the indicators catch fire. Contacts on the headphones and inside the case should be clean, without oxides and dust.
Leave the devices on charge for at least 15-20 minutes, even if the indicators show full charge. This is necessary to "wake up" the power controller. Sometimes the battery control system blocks the on-set at a critically low charge level. Stable voltage ensures that during the connection procedure the earphone does not turn off.
After charging, remove both headphones at the same time. If they are intended to be worn in the ears, make sure that protective films (if they were on new devices) are removed from the contact areas. Physical contact with the case is a prerequisite for starting the charging process and subsequent activation.
⚠️ Warning: If the indicator on the case does not light up when you install headphones, wipe the metal contacts with a dry soft cloth.
It is also important to check whether the mode of transportation, which is sometimes found in new electronics models, is activated, in which case the devices may not respond to the extraction from the case until the first full charge cycle.
⚠️ Note: Do not use damaged cables USB or adapters with unstable output current for charging the case, this can lead to incorrect operation of the power controller.
For successful synchronization, both earbuds must have a battery charge of at least 20-30%, otherwise the mating process may be interrupted halfway.
Standard procedure for connecting to a smartphone
When you're sure that the devices are charged, you can switch to pairing with your phone. Turn on Bluetooth on your Android or iOS smartphone. Open the charge case lid without removing the headphones yet, or remove them, depending on the model. On some Xiaomi models, the indicator starts flashing white to signal search mode.
A pop-up window should appear on your smartphone screen with a picture of the headphones and a suggestion to connect them. If the automatic window does not appear, go to the Bluetooth settings and find the device in the list of available. The name usually contains a model, for example, Xiaomi Earbuds Basic or Mi True Wireless.
Click on the name of the pairing device, which may require a code confirmation or just waiting for the process to be completed, a successful connection is confirmed by a voice message in the headphones or a characteristic beep, and then both channels must be in stereo mode.
- 🔍 Make sure that Bluetooth on your phone is on and visible to other devices.
- 🎧 Remove both earphones from the case at the same time to activate the mode (pairing).
- 📱 In the list of devices, select your model and click “Connect».
- ✅ Wait for a “Connected” voice confirmation or similar signal.
If two identical names appear on the list of devices (e.g., "Mi True Wireless Earbuds" twice), it means that the headphones are not synchronized with each other. They work as two mono devices, in which case a standard connection will not help, you need to perform the reset and repair procedure.
The solution to the problem: only one headphone works
When the sound is only in one ear, it is most often indicated that the left and right channels have been out of sync, the headphones have lost communication with each other and connected to the phone independently, or only one of them has activated Bluetooth connection, and restoring communication between the modules is a priority.
The first step is to remove the device from your phone's memory. Go to your Bluetooth settings, find your Xiaomi Earbuds, and select "Forget this device" or "Unpair it." Turn off Bluetooth on your smartphone completely. This will clear old configuration files that may interfere with proper operation.
Now, put both earbuds in the case and close the lid. Wait 5-10 seconds. Then reset (instruction below). After reset, reopen the case cover again. Indicators should blink, indicando ready for primary pairing. Now both earbuds should connect to each other, and then to the phone.
☑️ Checklist for elimination of desynchronization
Often the cause of the problem is a software glitch in the phone's operating system. Rebooting a smartphone before re-connecting can eliminate the Bluetooth driver conflict. Restarting the system frees up resources and resets network services.
⚠️ Warning: If after all the manipulations, one earphone is still silent, try connecting the headset to another smartphone. This will help you understand whether the problem lies in the headphones or in the phone.
Instructions for complete reset (Hard Reset)
Resetting is the most effective way to make headphones “forget” old mistakes and start working again. The procedure may vary slightly depending on the model, but the general principle is the same. For most Xiaomi and Redmi Buds models, you need to pinch the touch panels on both headphones.
Place the headphones in the case and leave the lid open. Press and hold the touch zones on both headphones simultaneously for 15-20 seconds. The headphone indicators (or the case, depending on the model) should flash red several times, then go out or light up white. This is a signal that the reset is done.
For some models, such as the Mi True Wireless Earphones 2, reset is done by long-term pressing of the button on the case itself (if it is provided by the design) or through the Mi Wear app.
Sequence of actions for discharge:
1. Put the headphones in the case.
2. Open the lid.
3.Push and hold 15-20s.
4. Wait for the indicator to flash.